Kod: Zaznacz cały
Linux version 2.6.25.6 (root@hall2000) (gcc version 4.1.2 20061115 (prerelease) (Debian 4.1.1-21)) #1 SMP Mon Jun 16 15:57:24 CEST 2008
BIOS-provided physical RAM map:
BIOS-e820: 0000000000000000 - 000000000009fc00 (usable)
BIOS-e820: 000000000009fc00 - 00000000000a0000 (reserved)
BIOS-e820: 00000000000f0000 - 0000000000100000 (reserved)
BIOS-e820: 0000000000100000 - 000000003fff0000 (usable)
BIOS-e820: 000000003fff0000 - 000000003fff3000 (ACPI NVS)
BIOS-e820: 000000003fff3000 - 0000000040000000 (ACPI data)
BIOS-e820: 00000000fec00000 - 00000000fec01000 (reserved)
BIOS-e820: 00000000fee00000 - 00000000fee01000 (reserved)
BIOS-e820: 00000000ffff0000 - 0000000100000000 (reserved)
127MB HIGHMEM available.
896MB LOWMEM available.
Scan SMP from c0000000 for 1024 bytes.
Scan SMP from c009fc00 for 1024 bytes.
Scan SMP from c00f0000 for 65536 bytes.
found SMP MP-table at [c00f5120] 000f5120
Entering add_active_range(0, 0, 262128) 0 entries of 256 used
Zone PFN ranges:
DMA 0 -> 4096
Normal 4096 -> 229376
HighMem 229376 -> 262128
Movable zone start PFN for each node
early_node_map[1] active PFN ranges
0: 0 -> 262128
On node 0 totalpages: 262128
DMA zone: 32 pages used for memmap
DMA zone: 0 pages reserved
DMA zone: 4064 pages, LIFO batch:0
Normal zone: 1760 pages used for memmap
Normal zone: 223520 pages, LIFO batch:31
HighMem zone: 255 pages used for memmap
HighMem zone: 32497 pages, LIFO batch:7
Movable zone: 0 pages used for memmap
DMI 2.3 present.
Using APIC driver default
ACPI: RSDP 000F6A70, 0014 (r0 Nvidia)
ACPI: RSDT 3FFF3000, 002C (r1 Nvidia AWRDACPI 42302E31 AWRD 1010101)
ACPI: FACP 3FFF3040, 0074 (r1 Nvidia AWRDACPI 42302E31 AWRD 1010101)
ACPI: DSDT 3FFF30C0, 43C2 (r1 NVIDIA AWRDACPI 1000 MSFT 100000C)
ACPI: FACS 3FFF0000, 0040
ACPI: APIC 3FFF74C0, 005A (r1 Nvidia AWRDACPI 42302E31 AWRD 1010101)
Nvidia board detected. Ignoring ACPI timer override.
If you got timer trouble try acpi_use_timer_override
ACPI: PM-Timer IO Port: 0x1008
ACPI: Local APIC address 0xfee00000
ACPI: LAPIC (acpi_id[0x00] lapic_id[0x00] enabled)
Processor #0 6:10 APIC version 16
ACPI: LAPIC_NMI (acpi_id[0x00] dfl dfl lint[0x1])
ACPI: IOAPIC (id[0x02] address[0xfec00000] gsi_base[0])
IOAPIC[0]: apic_id 2, version 17, address 0xfec00000, GSI 0-23
ACPI: INT_SRC_OVR (bus 0 bus_irq 0 global_irq 2 dfl dfl)
ACPI: BIOS IRQ0 pin2 override ignored.
ACPI: INT_SRC_OVR (bus 0 bus_irq 9 global_irq 9 high level)
ACPI: IRQ9 used by override.
Enabling APIC mode: Flat. Using 1 I/O APICs
Using ACPI (MADT) for SMP configuration information
Allocating PCI resources starting at 50000000 (gap: 40000000:bec00000)
Built 1 zonelists in Zone order, mobility grouping on. Total pages: 260081
Kernel command line: root=/dev/hdb1 ro
mapped APIC to ffffb000 (fee00000)
mapped IOAPIC to ffffa000 (fec00000)
Enabling fast FPU save and restore... done.
Enabling unmasked SIMD FPU exception support... done.
Initializing CPU#0
PID hash table entries: 4096 (order: 12, 16384 bytes)
Detected 1921.024 MHz processor.
Console: colour VGA+ 80x25
console [tty0] enabled
Dentry cache hash table entries: 131072 (order: 7, 524288 bytes)
Inode-cache hash table entries: 65536 (order: 6, 262144 bytes)
Memory: 1032128k/1048512k available (3918k kernel code, 15780k reserved, 1694k data, 320k init, 131008k highmem)
virtual kernel memory layout:
fixmap : 0xffe14000 - 0xfffff000 (1964 kB)
pkmap : 0xff800000 - 0xffc00000 (4096 kB)
vmalloc : 0xf8800000 - 0xff7fe000 ( 111 MB)
lowmem : 0xc0000000 - 0xf8000000 ( 896 MB)
.init : 0xc0683000 - 0xc06d3000 ( 320 kB)
.data : 0xc04d3815 - 0xc067b0fc (1694 kB)
.text : 0xc0100000 - 0xc04d3815 (3918 kB)
Checking if this processor honours the WP bit even in supervisor mode...Ok.
CPA: page pool initialized 1 of 1 pages preallocated
SLUB: Genslabs=12, HWalign=32, Order=0-1, MinObjects=4, CPUs=1, Nodes=1
Calibrating delay using timer specific routine.. 3845.24 BogoMIPS (lpj=7690491)
Mount-cache hash table entries: 512
CPU: L1 I Cache: 64K (64 bytes/line), D cache 64K (64 bytes/line)
CPU: L2 Cache: 512K (64 bytes/line)
Intel machine check architecture supported.
Intel machine check reporting enabled on CPU#0.
Compat vDSO mapped to ffffe000.
Checking 'hlt' instruction... OK.
SMP alternatives: switching to UP code
Freeing SMP alternatives: 18k freed
ACPI: Core revision 20070126
Parsing all Control Methods:
Table [DSDT](id 0001) - 693 Objects with 76 Devices 262 Methods 23 Regions
tbxface-0598 [00] tb_load_namespace : ACPI Tables successfully acquired
evxfevnt-0091 [00] enable : Transition to ACPI mode successful
CPU0: AMD Athlon(tm) XP 2600+ stepping 00
Total of 1 processors activated (3845.24 BogoMIPS).
ENABLING IO-APIC IRQs
..TIMER: vector=0x31 apic1=0 pin1=0 apic2=-1 pin2=-1
Brought up 1 CPUs
net_namespace: 244 bytes
NET: Registered protocol family 16
No dock devices found.
ACPI: bus type pci registered
PCI: PCI BIOS revision 2.10 entry at 0xfaab0, last bus=2
PCI: Using configuration type 1
Setting up standard PCI resources
evgpeblk-0956 [00] ev_create_gpe_block : GPE 00 to 1F [_GPE] 4 regs on int 0x9evgpeblk-0956 [00] ev_create_gpe_block : GPE 20 to 5F [_GPE] 8 regs on int 0x9evgpeblk-1052 [00] ev_initialize_gpe_bloc: Found 9 Wake, Enabled 0 Runtime GPEs in this block
evgpeblk-1052 [00] ev_initialize_gpe_bloc: Found 0 Wake, Enabled 0 Runtime GPEs in this block
ACPI: EC: Look up EC in DSDT
Completing Region/Field/Buffer/Package initialization:.................................................................
Initialized 20/23 Regions 1/1 Fields 29/29 Buffers 15/23 Packages (702 nodes)
Initializing Device/Processor/Thermal objects by executing _INI methods:.
Executed 1 _INI methods requiring 1 _STA executions (examined 79 objects)
ACPI: Interpreter enabled
ACPI: (supports S0 S1 S5)
ACPI: Using IOAPIC for interrupt routing
ACPI: PCI Root Bridge [PCI0] (0000:00)
pci 0000:00:00.0: nForce2 C1 Halt Disconnect fixup
ACPI: PCI Interrupt Routing Table [\_SB_.PCI0._PRT]
ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.HUB0._PRT]
ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.AGPB._PRT]
ACPI: PCI Interrupt Link [LNK1] (IRQs 3 4 5 6 7 9 10 *11 12 14 15)
ACPI: PCI Interrupt Link [LNK2] (IRQs 3 4 5 6 7 9 10 11 12 14 15) *0, disabled.
ACPI: PCI Interrupt Link [LNK3] (IRQs 3 4 5 6 7 9 10 11 12 14 15) *0, disabled.
ACPI: PCI Interrupt Link [LNK4] (IRQs 3 4 5 6 7 9 *10 11 12 14 15)
ACPI: PCI Interrupt Link [LNK5] (IRQs 3 4 5 6 7 9 10 11 12 14 15) *0, disabled.
ACPI: PCI Interrupt Link [LUBA] (IRQs 3 4 5 6 7 9 *10 11 12 14 15)
ACPI: PCI Interrupt Link [LUBB] (IRQs 3 4 5 6 7 9 10 *11 12 14 15)
ACPI: PCI Interrupt Link [LMAC] (IRQs 3 4 5 6 7 9 10 11 12 14 15) *0, disabled.
ACPI: PCI Interrupt Link [LAPU] (IRQs 3 4 5 6 7 9 10 11 12 14 15) *0, disabled.
ACPI: PCI Interrupt Link [LACI] (IRQs 3 4 *5 6 7 9 10 11 12 14 15)
ACPI: PCI Interrupt Link [LMCI] (IRQs 3 4 5 6 7 9 10 11 12 14 15) *0, disabled.
ACPI: PCI Interrupt Link [LSMB] (IRQs 3 4 *5 6 7 9 10 11 12 14 15)
ACPI: PCI Interrupt Link [LUB2] (IRQs 3 4 5 6 7 *9 10 11 12 14 15)
ACPI: PCI Interrupt Link [LFIR] (IRQs 3 4 5 6 7 9 10 11 12 14 15) *0, disabled.
ACPI: PCI Interrupt Link [L3CM] (IRQs 3 4 5 6 7 9 10 11 12 14 15) *0, disabled.
ACPI: PCI Interrupt Link [LIDE] (IRQs 3 4 5 6 7 9 10 11 12 14 15) *0, disabled.
ACPI: PCI Interrupt Link [APC1] (IRQs *16)
ACPI: PCI Interrupt Link [APC2] (IRQs *17), disabled.
ACPI: PCI Interrupt Link [APC3] (IRQs *18), disabled.
ACPI: PCI Interrupt Link [APC4] (IRQs *19)
ACPI: PCI Interrupt Link [APC5] (IRQs *16), disabled.
ACPI: PCI Interrupt Link [APCF] (IRQs 20 21 22) *0
ACPI: PCI Interrupt Link [APCG] (IRQs 20 21 22) *0
ACPI: PCI Interrupt Link [APCH] (IRQs 20 21 22) *0, disabled.
ACPI: PCI Interrupt Link [APCI] (IRQs 20 21 22) *0, disabled.
ACPI: PCI Interrupt Link [APCJ] (IRQs 20 21 22) *0
ACPI: PCI Interrupt Link [APCK] (IRQs 20 21 22) *0, disabled.
ACPI: PCI Interrupt Link [APCS] (IRQs *23)
ACPI: PCI Interrupt Link [APCL] (IRQs 20 21 22) *0
ACPI: PCI Interrupt Link [APCM] (IRQs 20 21 22) *0, disabled.
ACPI: PCI Interrupt Link [AP3C] (IRQs 20 21 22) *0, disabled.
ACPI: PCI Interrupt Link [APCZ] (IRQs 20 21 22) *0, disabled.
Linux Plug and Play Support v0.97 (c) Adam Belay
pnp: PnP ACPI init
ACPI: bus type pnp registered
pnp: PnP ACPI: found 14 devices
ACPI: ACPI bus type pnp unregistered
SCSI subsystem initialized
libata version 3.00 loaded.
usbcore: registered new interface driver usbfs
usbcore: registered new interface driver hub
usbcore: registered new device driver usb
PCI: Using ACPI for IRQ routing
PCI: If a device doesn't work, try "pci=routeirq". If it helps, post a report
system 00:00: ioport range 0x1000-0x107f has been reserved
system 00:00: ioport range 0x1080-0x10ff has been reserved
system 00:00: ioport range 0x1400-0x147f has been reserved
system 00:00: ioport range 0x1480-0x14ff has been reserved
system 00:00: ioport range 0x1800-0x187f has been reserved
system 00:00: ioport range 0x1880-0x18ff has been reserved
system 00:01: ioport range 0x1c00-0x1c3f has been reserved
system 00:01: ioport range 0x2000-0x203f has been reserved
system 00:02: iomem range 0xf0000-0xf3fff could not be reserved
system 00:02: iomem range 0xf4000-0xf7fff could not be reserved
system 00:02: iomem range 0xf8000-0xfbfff could not be reserved
system 00:02: iomem range 0xfc000-0xfffff could not be reserved
system 00:02: iomem range 0x3fff0000-0x3fffffff could not be reserved
system 00:02: iomem range 0xffff0000-0xffffffff could not be reserved
system 00:02: iomem range 0x0-0x9ffff could not be reserved
system 00:02: iomem range 0x100000-0x3ffeffff could not be reserved
system 00:02: iomem range 0xfec00000-0xfec00fff could not be reserved
system 00:02: iomem range 0xfee00000-0xfee00fff could not be reserved
system 00:04: ioport range 0x4d0-0x4d1 has been reserved
system 00:04: ioport range 0x800-0x805 has been reserved
system 00:04: ioport range 0x290-0x29f has been reserved
PCI: Bridge: 0000:00:08.0
IO window: c000-cfff
MEM window: 0xe7000000-0xe7ffffff
PREFETCH window: disabled.
PCI: Bridge: 0000:00:1e.0
IO window: disabled.
MEM window: 0xe4000000-0xe6ffffff
PREFETCH window: 0x00000000d0000000-0x00000000dfffffff
PCI: Setting latency timer of device 0000:00:08.0 to 64
NET: Registered protocol family 2
IP route cache hash table entries: 32768 (order: 5, 131072 bytes)
TCP established hash table entries: 131072 (order: 8, 1048576 bytes)
TCP bind hash table entries: 65536 (order: 7, 524288 bytes)
TCP: Hash tables configured (established 131072 bind 65536)
TCP reno registered
Machine check exception polling timer started.
microcode: CPU0 not a capable Intel processor
IA-32 Microcode Update Driver: v1.14a <tigran@aivazian.fsnet.co.uk>
highmem bounce pool size: 64 pages
Total HugeTLB memory allocated, 0
Installing knfsd (copyright (C) 1996 [email]okir@monad.swb.de[/email]).
io scheduler noop registered
io scheduler anticipatory registered
io scheduler deadline registered
io scheduler cfq registered (default)
pci 0000:02:00.0: Boot video device
input: Power Button (FF) as /class/input/input0
ACPI: Power Button (FF) [PWRF]
input: Power Button (CM) as /class/input/input1
ACPI: Power Button (CM) [PWRB]
ACPI: ACPI0007:00 is registered as cooling_device0
Real Time Clock Driver v1.12ac
Linux agpgart interface v0.103
Serial: 8250/16550 driver $Revision: 1.90 $ 4 ports, IRQ sharing disabled
serial8250: ttyS0 at I/O 0x3f8 (irq = 4) is a 16550A
serial8250: ttyS1 at I/O 0x2f8 (irq = 3) is a 16550A
00:0a: ttyS0 at I/O 0x3f8 (irq = 4) is a 16550A
00:0b: ttyS1 at I/O 0x2f8 (irq = 3) is a 16550A
Floppy drive(s): fd0 is 1.44M
FDC 0 is a post-1991 82077
brd: module loaded
loop: module loaded
Intel(R) PRO/1000 Network Driver - version 7.3.20-k2
Copyright (c) 1999-2006 Intel Corporation.
e100: Intel(R) PRO/100 Network Driver, 3.5.23-k4-NAPI
e100: Copyright(c) 1999-2006 Intel Corporation
8139too Fast Ethernet driver 0.9.28
ACPI: PCI Interrupt Link [APC1] enabled at IRQ 16
ACPI: PCI Interrupt 0000:01:0b.0[A] -> Link [APC1] -> GSI 16 (level, high) -> IRQ 16
eth0: RealTek RTL8139 at 0xf880c000, 00:0d:61:c4:b7:cb, IRQ 16
eth0: Identified 8139 chip type 'RTL-8100B/8139D'
Uniform Multi-Platform E-IDE driver
ide: Assuming 33MHz system bus speed for PIO modes; override with idebus=xx
NFORCE2: 0000:00:09.0 (rev a2) UDMA133 controller
NFORCE2: IDE controller (0x10de:0x0065 rev 0xa2) at PCI slot 0000:00:09.0
NFORCE2: not 100% native mode: will probe irqs later
NFORCE2: BIOS didn't set cable bits correctly. Enabling workaround.
ide0: BM-DMA at 0xf000-0xf007, BIOS settings: hda :D MA, hdb :D MA
ide1: BM-DMA at 0xf008-0xf00f, BIOS settings: hdc :D MA, hdd :D MA
Probing IDE interface ide0...
hda: ST3250820A, ATA DISK drive
Switched to high resolution mode on CPU 0
hdb: SAMSUNG SP0812N, ATA DISK drive
hda: host max PIO5 wanted PIO255(auto-tune) selected PIO4
hda: UDMA/100 mode selected
hdb: host max PIO5 wanted PIO255(auto-tune) selected PIO4
hdb: UDMA/100 mode selected
Probing IDE interface ide1...
hdc: DVD DC DW1670, ATAPI CD/DVD-ROM drive
hdc: host max PIO5 wanted PIO255(auto-tune) selected PIO4
hdc: host side 80-wire cable detection failed, limiting max speed to UDMA33
hdc: UDMA/33 mode selected
ide0 at 0x1f0-0x1f7,0x3f6 on irq 14
ide1 at 0x170-0x177,0x376 on irq 15
hda: max request size: 512KiB
hda: Host Protected Area detected.
current capacity is 488395055 sectors (250058 MB)
native capacity is 488397168 sectors (250059 MB)
hda: Host Protected Area disabled.
hda: 488397168 sectors (250059 MB) w/8192KiB Cache, CHS=30401/255/63
hda: cache flushes supported
hda: hda1 hda2 < hda5 hda6 >
hdb: max request size: 512KiB
hdb: Host Protected Area detected.
current capacity is 156365903 sectors (80059 MB)
native capacity is 156368016 sectors (80060 MB)
hdb: Host Protected Area disabled.
hdb: 156368016 sectors (80060 MB) w/8192KiB Cache, CHS=16383/255/63
hdb: cache flushes supported
hdb: hdb1 hdb2 < hdb5 hdb6 hdb7 hdb8 hdb9 >
hdc: ATAPI 126X DVD-ROM DVD-R-RAM CD-R/RW drive, 2048kB Cache
Uniform CD-ROM driver Revision: 3.20
3ware Storage Controller device driver for Linux v1.26.02.002.
Driver 'sd' needs updating - please use bus_type methods
Driver 'sr' needs updating - please use bus_type methods
Fusion MPT base driver 3.04.06
Copyright (c) 1999-2007 LSI Corporation
Fusion MPT SPI Host driver 3.04.06
ieee1394: raw1394: /dev/raw1394 device initialized
usbmon: debugfs is not available
ACPI: PCI Interrupt Link [APCL] enabled at IRQ 22
ACPI: PCI Interrupt 0000:00:02.2[C] -> Link [APCL] -> GSI 22 (level, high) -> IRQ 22
PCI: Setting latency timer of device 0000:00:02.2 to 64
ehci_hcd 0000:00:02.2: EHCI Host Controller
ehci_hcd 0000:00:02.2: new USB bus registered, assigned bus number 1
ehci_hcd 0000:00:02.2: debug port 1
PCI: cache line size of 64 is not supported by device 0000:00:02.2
ehci_hcd 0000:00:02.2: irq 22, io mem 0xe8005000
ehci_hcd 0000:00:02.2: USB 2.0 started, EHCI 1.00, driver 10 Dec 2004
usb usb1: configuration #1 chosen from 1 choice
hub 1-0:1.0: USB hub found
hub 1-0:1.0: 6 ports detected
ohci_hcd: 2006 August 04 USB 1.1 'Open' Host Controller (OHCI) Driver
ACPI: PCI Interrupt Link [APCF] enabled at IRQ 21
ACPI: PCI Interrupt 0000:00:02.0[A] -> Link [APCF] -> GSI 21 (level, high) -> IRQ 21
PCI: Setting latency timer of device 0000:00:02.0 to 64
ohci_hcd 0000:00:02.0: OHCI Host Controller
ohci_hcd 0000:00:02.0: new USB bus registered, assigned bus number 2
ohci_hcd 0000:00:02.0: irq 21, io mem 0xe8003000
usb usb2: configuration #1 chosen from 1 choice
hub 2-0:1.0: USB hub found
hub 2-0:1.0: 3 ports detected
ACPI: PCI Interrupt Link [APCG] enabled at IRQ 20
ACPI: PCI Interrupt 0000:00:02.1[B] -> Link [APCG] -> GSI 20 (level, high) -> IRQ 20
PCI: Setting latency timer of device 0000:00:02.1 to 64
ohci_hcd 0000:00:02.1: OHCI Host Controller
ohci_hcd 0000:00:02.1: new USB bus registered, assigned bus number 3
ohci_hcd 0000:00:02.1: irq 20, io mem 0xe8004000
hub 1-0:1.0: unable to enumerate USB device on port 1
usb usb3: configuration #1 chosen from 1 choice
hub 3-0:1.0: USB hub found
hub 3-0:1.0: 3 ports detected
USB Universal Host Controller Interface driver v3.0
hub 1-0:1.0: unable to enumerate USB device on port 5
usb 2-1: new low speed USB device using ohci_hcd and address 2
usb 2-1: configuration #1 chosen from 1 choice
usb 2-3: new full speed USB device using ohci_hcd and address 3
usb 2-3: configuration #1 chosen from 1 choice
usbcore: registered new interface driver usblp
Initializing USB Mass Storage driver...
usbcore: registered new interface driver usb-storage
USB Mass Storage support registered.
PNP: No PS/2 controller found. Probing ports directly.
serio: i8042 KBD port at 0x60,0x64 irq 1
serio: i8042 AUX port at 0x60,0x64 irq 12
mice: PS/2 mouse device common for all mice
device-mapper: ioctl: 4.13.0-ioctl (2007-10-18) initialised: [email]dm-devel@redhat.comc[/email]puidle: using governor ladder
cpuidle: using governor menu
input: Logitech HID compliant keyboard as /class/input/input2
input: USB HID v1.10 Keyboard [Logitech HID compliant keyboard] on usb-0000:00:02.0-1
input: Logitech HID compliant keyboard as /class/input/input3
input: USB HID v1.10 Device [Logitech HID compliant keyboard] on usb-0000:00:02.0-1
input: Razer Razer Copperhead Laser Mouse as /class/input/input4
input: USB HID v1.00 Mouse [Razer Razer Copperhead Laser Mouse] on usb-0000:00:02.0-3
input: Razer Razer Copperhead Laser Mouse as /class/input/input5
input: USB HID v0.01 Keyboard [Razer Razer Copperhead Laser Mouse] on usb-0000:00:02.0-3
usbcore: registered new interface driver usbhid
drivers/hid/usbhid/hid-core.c: v2.6:USB HID core driver
Advanced Linux Sound Architecture Driver Version 1.0.16rc2 (Thu Jan 31 16:40:16 2008 UTC).
ALSA device list:
No soundcards found.
oprofile: using NMI interrupt.
TCP cubic registered
NET: Registered protocol family 1
NET: Registered protocol family 10
IPv6 over IPv4 tunneling driver
NET: Registered protocol family 17
RPC: Registered udp transport module.
RPC: Registered tcp transport module.
powernow-k8: Processor cpuid 6a0 not supported
Using IPI No-Shortcut mode
kjournald starting. Commit interval 5 seconds
EXT3-fs: mounted filesystem with ordered data mode.
VFS: Mounted root (ext3 filesystem) readonly.
Freeing unused kernel memory: 320k freed
agpgart: Detected NVIDIA nForce2 chipset
agpgart: AGP aperture is 64M @ 0xe0000000
ACPI: PCI Interrupt Link [APCJ] enabled at IRQ 22
ACPI: PCI Interrupt 0000:00:06.0[A] -> Link [APCJ] -> GSI 22 (level, high) -> IRQ 22
PCI: Setting latency timer of device 0000:00:06.0 to 64
Linux video capture interface: v2.00
saa7130/34: v4l2 driver version 0.2.14 loaded
parport_pc 00:0c: reported by Plug and Play ACPI
parport0: PC-style at 0x378 (0x778), irq 7 [PCSPP(,...)]
intel8x0_measure_ac97_clock: measured 54750 usecs
intel8x0: clocking to 47494
ACPI: PCI Interrupt 0000:01:08.0[A] -> Link [APC1] -> GSI 16 (level, high) -> IRQ 16
saa7130[0]: found at 0000:01:08.0, rev: 1, irq: 16, latency: 32, mmio: 0xe7000000
saa7130[0]: subsystem: 0919:2003, board: Proteus Pro 2309 [card=98,autodetected]saa7130[0]: board init: gpio is ff
input: saa7134 IR (Proteus Pro 2309) as /class/input/input6
saa7130[0]: i2c eeprom 00: 19 09 03 20 08 20 1c 55 43 43 a9 1c 55 43 43 a9
saa7130[0]: i2c eeprom 10: ff ff 00 00 ff ff ff ff ff ff ff ff ff ff ff ff
saa7130[0]: i2c eeprom 20: ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff
saa7130[0]: i2c eeprom 30: ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff
saa7130[0]: i2c eeprom 40: ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff
saa7130[0]: i2c eeprom 50: ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff
saa7130[0]: i2c eeprom 60: ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff
saa7130[0]: i2c eeprom 70: ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff
saa7130[0]: i2c eeprom 80: ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff
saa7130[0]: i2c eeprom 90: ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff
saa7130[0]: i2c eeprom a0: ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff
saa7130[0]: i2c eeprom b0: ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff
saa7130[0]: i2c eeprom c0: ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff
saa7130[0]: i2c eeprom d0: ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff
saa7130[0]: i2c eeprom e0: ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff
saa7130[0]: i2c eeprom f0: ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff
saa7130[0]: registered device video0 [v4l2]
saa7130[0]: registered device vbi0
Adding 2345448k swap on /dev/hdb7. Priority:-1 extents:1 across:2345448k
EXT3 FS on hdb1, internal journal
kjournald starting. Commit interval 5 seconds
EXT3 FS on hdb9, internal journal
EXT3-fs: mounted filesystem with ordered data mode.
kjournald starting. Commit interval 5 seconds
EXT3 FS on hdb8, internal journal
EXT3-fs: mounted filesystem with ordered data mode.
kjournald starting. Commit interval 5 seconds
EXT3 FS on hdb5, internal journal
EXT3-fs: mounted filesystem with ordered data mode.
kjournald starting. Commit interval 5 seconds
EXT3 FS on hdb6, internal journal
EXT3-fs: mounted filesystem with ordered data mode.
eth0: link up, 100Mbps, full-duplex, lpa 0x45E1
warning: `avahi-daemon' uses 32-bit capabilities (legacy support in use)
eth0: no IPv6 routers present
nvidia: module license 'NVIDIA' taints kernel.
ACPI: PCI Interrupt Link [APC4] enabled at IRQ 19
ACPI: PCI Interrupt 0000:02:00.0[A] -> Link [APC4] -> GSI 19 (level, high) -> IRQ 19
NVRM: loading NVIDIA UNIX x86 Kernel Module 173.14.05 Mon May 19 00:06:12 PDT 2008
agpgart: Found an AGP 3.0 compliant device at 0000:00:00.0.
agpgart: Putting AGP V3 device at 0000:00:00.0 into 8x mode
agpgart: Putting AGP V3 device at 0000:02:00.0 into 8x mode
cdrom: hdc: mrw address space DMA selected
ISO 9660 Extensions: RRIP_1991A
usb 2-3: USB disconnect, address 3
hub 1-0:1.0: unable to enumerate USB device on port 5
usb 2-3: new full speed USB device using ohci_hcd and address 4
usb 2-3: configuration #1 chosen from 1 choice
input: Razer Razer Copperhead Laser Mouse as /class/input/input7
input: USB HID v1.00 Mouse [Razer Razer Copperhead Laser Mouse] on usb-0000:00:02.0-3
input: Razer Razer Copperhead Laser Mouse as /class/input/input8
input: USB HID v0.01 Keyboard [Razer Razer Copperhead Laser Mouse] on usb-0000:00:02.0-3
process `skype' is using obsolete setsockopt SO_BSDCOMPAT
A tak wygląda zrzut z ekranu włączonego tvtime na wejście composite2. Podłączona jest mała kamera. Widać jednocześnie, że obraz jest u góry obcięty i przeniesiony kawałek klatki z dołu jak w starym magnetowidzie wujka Zdziśka
.