Polski portal użytkowników dystrybucji Debian GNU/Linux, dyskusje, artykuły, nowości, blog, porady, pomoc.
https://www.debian.pl/
na kabelku jest ok, lecz chce połączyć się WiFi, jak to zrobić? Proszę o pomoc na chłopski rozum, nowym członkiem Linux'a jestem.Kod: Zaznacz cały
lspci -kKod: Zaznacz cały
cat /etc/debian_version
Kod: Zaznacz cały
rfkill list allKod: Zaznacz cały
lspci -nnk | grep -iA2 netKod: Zaznacz cały
ip link showKod: Zaznacz cały
julcia@192:~$ [b]lspci -nnk | grep -iA2 net[/b]
02:08.0 Ethernet controller [0200]: Intel Corporation 82562ET/EZ/GT/GZ - PRO/100 VE (LOM) Ethernet Controller Mobile [8086:1068] (rev 01)
Subsystem: Hewlett-Packard Company 530 Laptop [103c:30d5]
Kernel driver in use: e100
--
10:00.0 Network controller [0280]: Broadcom Limited BCM4311 802.11b/g WLAN [14e4:4311] (rev 01)
Subsystem: Hewlett-Packard Company BCM4311 802.11b/g Wireless LAN Controller [103c:1364]
Kernel driver in use: b43-pci-bridge
Kod: Zaznacz cały
dmesg | grep -i firmwareKod: Zaznacz cały
cat /etc/apt/sources.listKod: Zaznacz cały
root@192:/home/julcia# dmesg | grep -i firmware
[ 0.138848] [Firmware Bug]: ACPI: No _BQC method, cannot determine initial brightness
[ 0.154203] acpi PNP0A08:00: [Firmware Info]: MMCONFIG for domain 0000 [bus 00-3f] only partially covers this bridge
[ 0.228555] pci 0000:02:08.0: Firmware left e100 interrupts enabled; disabling
[ 9.335940] [Firmware Bug]: _BCQ is used instead of _BQC
[ 9.336412] [Firmware Bug]: ACPI: No _BQC method, cannot determine initial brightness
[ 13.148207] b43 ssb0:0: firmware: failed to load b43/ucode5.fw (-2)
[ 13.148285] b43 ssb0:0: Direct firmware load for b43/ucode5.fw failed with error -2
[ 13.148309] b43 ssb0:0: firmware: failed to load b43/ucode5.fw (-2)
[ 13.148369] b43 ssb0:0: Direct firmware load for b43/ucode5.fw failed with error -2
[ 13.148461] b43 ssb0:0: firmware: failed to load b43-open/ucode5.fw (-2)
[ 13.148527] b43 ssb0:0: Direct firmware load for b43-open/ucode5.fw failed with error -2
[ 13.148542] b43 ssb0:0: firmware: failed to load b43-open/ucode5.fw (-2)
[ 13.148606] b43 ssb0:0: Direct firmware load for b43-open/ucode5.fw failed with error -2
[ 13.148610] b43-phy0 ERROR: You must go to http://wireless.kernel.org/en/users/Drivers/b43#devicefirmware and download the correct firmware for this driver version. Please carefully read all instructions on this website.
root@192:/home/julcia#
Kod: Zaznacz cały
root@192:/home/julcia# ip link show
1: lo: <LOOPBACK,UP,LOWER_UP> mtu 65536 qdisc noqueue state UNKNOWN mode DEFAULT group default qlen 1
link/loopback 00:00:00:00:00:00 brd 00:00:00:00:00:00
2: enp2s8: <BROADCAST,MULTICAST,UP,LOWER_UP> mtu 1500 qdisc pfifo_fast state UP mode DEFAULT group default qlen 1000
link/ether 00:1b:38:8c:b4:e3 brd ff:ff:ff:ff:ff:ff
root@192:/home/julcia#
Kod: Zaznacz cały
root@192:/home/julcia# cat /etc/apt/sources.list
#
# deb cdrom:[Debian GNU/Linux 9.4.0 _Stretch_ - Official i386 xfce-CD Binary-1 20180310-11:55]/ stretch main
deb cdrom:[Debian GNU/Linux 9.4.0 _Stretch_ - Official i386 xfce-CD Binary-1 20180310-11:55]/ stretch main
deb http://ftp.pl.debian.org/debian/ stretch main
deb-src http://ftp.pl.debian.org/debian/ stretch main
deb http://security.debian.org/debian-security stretch/updates main
deb-src http://security.debian.org/debian-security stretch/updates main
# stretch-updates, previously known as 'volatile'
deb http://ftp.pl.debian.org/debian/ stretch-updates main
deb-src http://ftp.pl.debian.org/debian/ stretch-updates main
root@192:/home/julcia#
Kod: Zaznacz cały
deb http://ftp.pl.debian.org/debian/ stretch mainKod: Zaznacz cały
deb http://ftp.pl.debian.org/debian/ stretch main contrib non-freeKod: Zaznacz cały
bash: deb: nie znaleziono poleceniaKod: Zaznacz cały
apt-get install firmware-b43-installerKod: Zaznacz cały
Czytanie list pakietów... Gotowe
Budowanie drzewa zależności
Odczyt informacji o stanie... Gotowe
E: Nie udało się odnaleźć pakietu firmware-b43-installer