Witam wszystkich. Parę dni temu zacząłem swoją przygodę z Linuxem, od zainstalowania systemu Lubuntu, wybór padł na ten system ponieważ komputer na którym jest zainstalowany został kupiony w 2004 roku ;p i ma służyć do przeglądania internetu i właśnie odkrywania Linuxa ;p System działa bezproblemowo. Czytałem również właśnie o #! i postanowiłem nagrać .iso na pendriva, na razie korzystałem z wersji live bez instalacji, jednak na PC jak i również na nowszym laptopie nie mogę połączyć się z internetem, sam nie potrafię rozwiązać tego problemu, a szkoda bo system przypadł mi bardziej do gustu niż Lubuntu i moim zdaniem OpenBox > LXDE ;p
Wklejam outputy z komend ;p
[HTML]ip link
========================================================================
1: lo: <LOOPBACK,UP,LOWER_UP> mtu 65536 qdisc noqueue state UNKNOWN mode DEFAULT group default
link/loopback 00:00:00:00:00:00 brd 00:00:00:00:00:00
2: eth0: <NO-CARRIER,BROADCAST,MULTICAST,UP> mtu 1500 qdisc pfifo_fast state DOWN mode DEFAULT group default qlen 1000
link/ether 00:0f:ea:ea:94:ae brd ff:ff:ff:ff:ff:ff
3: wlan0: <BROADCAST,MULTICAST,UP,LOWER_UP> mtu 1500 qdisc pfifo_fast state UP mode DORMANT group default qlen 1000
link/ether 00:60:b3:0e:5f:fd brd ff:ff:ff:ff:ff:ff
lsusb -v
=========================================================================
Bus 001 Device 002: ID 079b:0062 Sagem XG-76NA 802.11bg
Device Descriptor:
bLength 18
bDescriptorType 1
bcdUSB 2.00
bDeviceClass 255 Vendor Specific Class
bDeviceSubClass 255 Vendor Specific Subclass
bDeviceProtocol 255 Vendor Specific Protocol
bMaxPacketSize0 64
idVendor 0x079b Sagem
idProduct 0x0062 XG-76NA 802.11bg
bcdDevice 48.10
iManufacturer 16
iProduct 32
iSerial 0
bNumConfigurations 1
Configuration Descriptor:
bLength 9
bDescriptorType 2
wTotalLength 46
bNumInterfaces 1
bConfigurationValue 1
iConfiguration 0
bmAttributes 0x80
(Bus Powered)
MaxPower 500mA
Interface Descriptor:
bLength 9
bDescriptorType 4
bInterfaceNumber 0
bAlternateSetting 0
bNumEndpoints 4
bInterfaceClass 255 Vendor Specific Class
bInterfaceSubClass 0
bInterfaceProtocol 0
iInterface 0
Endpoint Descriptor:
bLength 7
bDescriptorType 5
bEndpointAddress 0x01 EP 1 OUT
bmAttributes 2
Transfer Type Bulk
Synch Type None
Usage Type Data
wMaxPacketSize 0x0200 1x 512 bytes
bInterval 0
Endpoint Descriptor:
bLength 7
bDescriptorType 5
bEndpointAddress 0x82 EP 2 IN
bmAttributes 2
Transfer Type Bulk
Synch Type None
Usage Type Data
wMaxPacketSize 0x0200 1x 512 bytes
bInterval 0
Endpoint Descriptor:
bLength 7
bDescriptorType 5
bEndpointAddress 0x83 EP 3 IN
bmAttributes 3
Transfer Type Interrupt
Synch Type None
Usage Type Data
wMaxPacketSize 0x0040 1x 64 bytes
bInterval 1
Endpoint Descriptor:
bLength 7
bDescriptorType 5
bEndpointAddress 0x04 EP 4 OUT
bmAttributes 3
Transfer Type Interrupt
Synch Type None
Usage Type Data
wMaxPacketSize 0x0040 1x 64 bytes
bInterval 1
Bus 001 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub
Device Descriptor:
bLength 18
bDescriptorType 1
bcdUSB 2.00
bDeviceClass 9 Hub
bDeviceSubClass 0 Unused
bDeviceProtocol 0 Full speed (or root) hub
bMaxPacketSize0 64
idVendor 0x1d6b Linux Foundation
idProduct 0x0002 2.0 root hub
bcdDevice 3.13
iManufacturer 3
iProduct 2
iSerial 1
bNumConfigurations 1
Configuration Descriptor:
bLength 9
bDescriptorType 2
wTotalLength 25
bNumInterfaces 1
bConfigurationValue 1
iConfiguration 0
bmAttributes 0xe0
Self Powered
Remote Wakeup
MaxPower 0mA
Interface Descriptor:
bLength 9
bDescriptorType 4
bInterfaceNumber 0
bAlternateSetting 0
bNumEndpoints 1
bInterfaceClass 9 Hub
bInterfaceSubClass 0 Unused
bInterfaceProtocol 0 Full speed (or root) hub
iInterface 0
Endpoint Descriptor:
bLength 7
bDescriptorType 5
bEndpointAddress 0x81 EP 1 IN
bmAttributes 3
Transfer Type Interrupt
Synch Type None
Usage Type Data
wMaxPacketSize 0x0004 1x 4 bytes
bInterval 12
Bus 004 Device 002: ID 1bcf:0007 Sunplus Innovation Technology Inc. Optical Mouse
Device Descriptor:
bLength 18
bDescriptorType 1
bcdUSB 2.00
bDeviceClass 0 (Defined at Interface level)
bDeviceSubClass 0
bDeviceProtocol 0
bMaxPacketSize0 8
idVendor 0x1bcf Sunplus Innovation Technology Inc.
idProduct 0x0007 Optical Mouse
bcdDevice 0.14
iManufacturer 0
iProduct 2
iSerial 0
bNumConfigurations 1
Configuration Descriptor:
bLength 9
bDescriptorType 2
wTotalLength 34
bNumInterfaces 1
bConfigurationValue 1
iConfiguration 0
bmAttributes 0xa0
(Bus Powered)
Remote Wakeup
MaxPower 98mA
Interface Descriptor:
bLength 9
bDescriptorType 4
bInterfaceNumber 0
bAlternateSetting 0
bNumEndpoints 1
bInterfaceClass 3 Human Interface Device
bInterfaceSubClass 1 Boot Interface Subclass
bInterfaceProtocol 2 Mouse
iInterface 0
HID Device Descriptor:
bLength 9
bDescriptorType 33
bcdHID 1.10
bCountryCode 0 Not supported
bNumDescriptors 1
bDescriptorType 34 Report
wDescriptorLength 99
Report Descriptors:
** UNAVAILABLE **
Endpoint Descriptor:
bLength 7
bDescriptorType 5
bEndpointAddress 0x81 EP 1 IN
bmAttributes 3
Transfer Type Interrupt
Synch Type None
Usage Type Data
wMaxPacketSize 0x0007 1x 7 bytes
bInterval 10
Bus 004 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub
Device Descriptor:
bLength 18
bDescriptorType 1
bcdUSB 1.10
bDeviceClass 9 Hub
bDeviceSubClass 0 Unused
bDeviceProtocol 0 Full speed (or root) hub
bMaxPacketSize0 64
idVendor 0x1d6b Linux Foundation
idProduct 0x0001 1.1 root hub
bcdDevice 3.13
iManufacturer 3
iProduct 2
iSerial 1
bNumConfigurations 1
Configuration Descriptor:
bLength 9
bDescriptorType 2
wTotalLength 25
bNumInterfaces 1
bConfigurationValue 1
iConfiguration 0
bmAttributes 0xe0
Self Powered
Remote Wakeup
MaxPower 0mA
Interface Descriptor:
bLength 9
bDescriptorType 4
bInterfaceNumber 0
bAlternateSetting 0
bNumEndpoints 1
bInterfaceClass 9 Hub
bInterfaceSubClass 0 Unused
bInterfaceProtocol 0 Full speed (or root) hub
iInterface 0
Endpoint Descriptor:
bLength 7
bDescriptorType 5
bEndpointAddress 0x81 EP 1 IN
bmAttributes 3
Transfer Type Interrupt
Synch Type None
Usage Type Data
wMaxPacketSize 0x0002 1x 2 bytes
bInterval 255
Bus 003 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub
Device Descriptor:
bLength 18
bDescriptorType 1
bcdUSB 1.10
bDeviceClass 9 Hub
bDeviceSubClass 0 Unused
bDeviceProtocol 0 Full speed (or root) hub
bMaxPacketSize0 64
idVendor 0x1d6b Linux Foundation
idProduct 0x0001 1.1 root hub
bcdDevice 3.13
iManufacturer 3
iProduct 2
iSerial 1
bNumConfigurations 1
Configuration Descriptor:
bLength 9
bDescriptorType 2
wTotalLength 25
bNumInterfaces 1
bConfigurationValue 1
iConfiguration 0
bmAttributes 0xe0
Self Powered
Remote Wakeup
MaxPower 0mA
Interface Descriptor:
bLength 9
bDescriptorType 4
bInterfaceNumber 0
bAlternateSetting 0
bNumEndpoints 1
bInterfaceClass 9 Hub
bInterfaceSubClass 0 Unused
bInterfaceProtocol 0 Full speed (or root) hub
iInterface 0
Endpoint Descriptor:
bLength 7
bDescriptorType 5
bEndpointAddress 0x81 EP 1 IN
bmAttributes 3
Transfer Type Interrupt
Synch Type None
Usage Type Data
wMaxPacketSize 0x0002 1x 2 bytes
bInterval 255
Bus 002 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub
Device Descriptor:
bLength 18
bDescriptorType 1
bcdUSB 1.10
bDeviceClass 9 Hub
bDeviceSubClass 0 Unused
bDeviceProtocol 0 Full speed (or root) hub
bMaxPacketSize0 64
idVendor 0x1d6b Linux Foundation
idProduct 0x0001 1.1 root hub
bcdDevice 3.13
iManufacturer 3
iProduct 2
iSerial 1
bNumConfigurations 1
Configuration Descriptor:
bLength 9
bDescriptorType 2
wTotalLength 25
bNumInterfaces 1
bConfigurationValue 1
iConfiguration 0
bmAttributes 0xe0
Self Powered
Remote Wakeup
MaxPower 0mA
Interface Descriptor:
bLength 9
bDescriptorType 4
bInterfaceNumber 0
bAlternateSetting 0
bNumEndpoints 1
bInterfaceClass 9 Hub
bInterfaceSubClass 0 Unused
bInterfaceProtocol 0 Full speed (or root) hub
iInterface 0
Endpoint Descriptor:
bLength 7
bDescriptorType 5
bEndpointAddress 0x81 EP 1 IN
bmAttributes 3
Transfer Type Interrupt
Synch Type None
Usage Type Data
wMaxPacketSize 0x0002 1x 2 bytes
bInterval 255[/HTML]
Acha, zwracam się o pomoc na tym forum ponieważ czytałem, że #! jest oparty na Debianie. Jeżeli się pomyliłem lub spowodowałem niepotrzebne zamieszania to z góry przepraszam.
[+] CrunchBang problem z kart
Uzupełnij informacje według wzorca: threads/12771-Zakładając-temat-przeczyt ... #post81406
To powinno pomóc: https://wiki.debian.org/zd1211rw
To powinno pomóc: https://wiki.debian.org/zd1211rw
uname -a
=========================================
[HTML]Linux bartek-desktop 3.13.0-24-generic #46-Ubuntu SMP Thu Apr 10 19:08:14 UTC 2014 i686 athlon i686 GNU/Linux
[/HTML]
Wersja architektury systemu:
=========================================
i386
=========================================
lspci -n
[HTML]00:00.0 0600: 10b9:1689
00:01.0 0604: 10b9:5246
00:02.0 0604: 10b9:5249
00:03.0 0601: 10b9:1563 (rev 70)
00:03.1 0680: 10b9:7101
00:04.0 0401: 10b9:5455 (rev 20)
00:0e.0 0101: 10b9:5229 (rev c7)
00:0e.1 0180: 10b9:5289 (rev 10)
00:0f.0 0c03: 10b9:5237 (rev 03)
00:0f.1 0c03: 10b9:5237 (rev 03)
00:0f.2 0c03: 10b9:5237 (rev 03)
00:0f.3 0c03: 10b9:5239 (rev 01)
00:18.0 0600: 1022:1100
00:18.1 0600: 1022:1101
00:18.2 0600: 1022:1102
00:18.3 0600: 1022:1103
01:00.0 0300: 1002:4153
01:00.1 0380: 1002:4173
02:0a.0 0200: 10ec:8139 (rev 10)[/HTML]
======================================
lspci - k
[HTML]00:00.0 Host bridge: ULi Electronics Inc. M1689 K8 Northbridge [Super K8 Single Chip]
Subsystem: Gigabyte Technology Co., Ltd Device 5000
Kernel driver in use: agpgart-amd64
00:01.0 PCI bridge: ULi Electronics Inc. AGP8X Controller
00:02.0 PCI bridge: ULi Electronics Inc. M5249 HTT to PCI Bridge
00:03.0 ISA bridge: ULi Electronics Inc. M1563 HyperTransport South Bridge (rev 70)
Subsystem: Gigabyte Technology Co., Ltd Device 5001
Kernel driver in use: ali1563_smbus
00:03.1 Bridge: ULi Electronics Inc. M7101 Power Management Controller [PMU]
Subsystem: Gigabyte Technology Co., Ltd Device 5003
00:04.0 Multimedia audio controller: ULi Electronics Inc. M5455 PCI AC-Link Controller Audio Device (rev 20)
Subsystem: Gigabyte Technology Co., Ltd Device ae01
Kernel driver in use: snd_intel8x0
00:0e.0 IDE interface: ULi Electronics Inc. M5229 IDE (rev c7)
Subsystem: Gigabyte Technology Co., Ltd Device 5002
Kernel driver in use: pata_ali
00:0e.1 Mass storage controller: ULi Electronics Inc. ULi 5289 SATA (rev 10)
Subsystem: Gigabyte Technology Co., Ltd Device b003
Kernel driver in use: sata_uli
00:0f.0 USB controller: ULi Electronics Inc. USB 1.1 Controller (rev 03)
Subsystem: Gigabyte Technology Co., Ltd Device 5004
Kernel driver in use: ohci-pci
00:0f.1 USB controller: ULi Electronics Inc. USB 1.1 Controller (rev 03)
Subsystem: Gigabyte Technology Co., Ltd Device 5004
Kernel driver in use: ohci-pci
00:0f.2 USB controller: ULi Electronics Inc. USB 1.1 Controller (rev 03)
Subsystem: Gigabyte Technology Co., Ltd Device 5004
Kernel driver in use: ohci-pci
00:0f.3 USB controller: ULi Electronics Inc. USB 2.0 Controller (rev 01)
Subsystem: Gigabyte Technology Co., Ltd Device 5004
Kernel driver in use: ehci-pci
00:18.0 Host bridge: Advanced Micro Devices, Inc. [AMD] K8 [Athlon64/Opteron] HyperTransport Technology Configuration
00:18.1 Host bridge: Advanced Micro Devices, Inc. [AMD] K8 [Athlon64/Opteron] Address Map
00:18.2 Host bridge: Advanced Micro Devices, Inc. [AMD] K8 [Athlon64/Opteron] DRAM Controller
00:18.3 Host bridge: Advanced Micro Devices, Inc. [AMD] K8 [Athlon64/Opteron] Miscellaneous Control
Kernel driver in use: k8temp
01:00.0 VGA compatible controller: Advanced Micro Devices, Inc. [AMD/ATI] RV350 [Radeon 9550]
Subsystem: Gigabyte Technology Co., Ltd Device 4050
Kernel driver in use: radeon
01:00.1 Display controller: Advanced Micro Devices, Inc. [AMD/ATI] RV350 [Radeon 9550] (Secondary)
Subsystem: Gigabyte Technology Co., Ltd Device 4051
02:0a.0 Ethernet controller: Realtek Semiconductor Co., Ltd. RTL-8100/8101L/8139 PCI Fast Ethernet Adapter (rev 10)
Subsystem: Gigabyte Technology Co., Ltd GA-7VM400M/7VT600 Motherboard
Kernel driver in use: 8139too
bartek@bartek-desktop:~$
bartek@bartek-desktop:~$ lspci -k
00:00.0 Host bridge: ULi Electronics Inc. M1689 K8 Northbridge [Super K8 Single Chip]
Subsystem: Gigabyte Technology Co., Ltd Device 5000
Kernel driver in use: agpgart-amd64
00:01.0 PCI bridge: ULi Electronics Inc. AGP8X Controller
00:02.0 PCI bridge: ULi Electronics Inc. M5249 HTT to PCI Bridge
00:03.0 ISA bridge: ULi Electronics Inc. M1563 HyperTransport South Bridge (rev 70)
Subsystem: Gigabyte Technology Co., Ltd Device 5001
Kernel driver in use: ali1563_smbus
00:03.1 Bridge: ULi Electronics Inc. M7101 Power Management Controller [PMU]
Subsystem: Gigabyte Technology Co., Ltd Device 5003
00:04.0 Multimedia audio controller: ULi Electronics Inc. M5455 PCI AC-Link Controller Audio Device (rev 20)
Subsystem: Gigabyte Technology Co., Ltd Device ae01
Kernel driver in use: snd_intel8x0
00:0e.0 IDE interface: ULi Electronics Inc. M5229 IDE (rev c7)
Subsystem: Gigabyte Technology Co., Ltd Device 5002
Kernel driver in use: pata_ali
00:0e.1 Mass storage controller: ULi Electronics Inc. ULi 5289 SATA (rev 10)
Subsystem: Gigabyte Technology Co., Ltd Device b003
Kernel driver in use: sata_uli
00:0f.0 USB controller: ULi Electronics Inc. USB 1.1 Controller (rev 03)
Subsystem: Gigabyte Technology Co., Ltd Device 5004
Kernel driver in use: ohci-pci
00:0f.1 USB controller: ULi Electronics Inc. USB 1.1 Controller (rev 03)
Subsystem: Gigabyte Technology Co., Ltd Device 5004
Kernel driver in use: ohci-pci
00:0f.2 USB controller: ULi Electronics Inc. USB 1.1 Controller (rev 03)
Subsystem: Gigabyte Technology Co., Ltd Device 5004
Kernel driver in use: ohci-pci
00:0f.3 USB controller: ULi Electronics Inc. USB 2.0 Controller (rev 01)
Subsystem: Gigabyte Technology Co., Ltd Device 5004
Kernel driver in use: ehci-pci
00:18.0 Host bridge: Advanced Micro Devices, Inc. [AMD] K8 [Athlon64/Opteron] HyperTransport Technology Configuration
00:18.1 Host bridge: Advanced Micro Devices, Inc. [AMD] K8 [Athlon64/Opteron] Address Map
00:18.2 Host bridge: Advanced Micro Devices, Inc. [AMD] K8 [Athlon64/Opteron] DRAM Controller
00:18.3 Host bridge: Advanced Micro Devices, Inc. [AMD] K8 [Athlon64/Opteron] Miscellaneous Control
Kernel driver in use: k8temp
01:00.0 VGA compatible controller: Advanced Micro Devices, Inc. [AMD/ATI] RV350 [Radeon 9550]
Subsystem: Gigabyte Technology Co., Ltd Device 4050
Kernel driver in use: radeon
01:00.1 Display controller: Advanced Micro Devices, Inc. [AMD/ATI] RV350 [Radeon 9550] (Secondary)
Subsystem: Gigabyte Technology Co., Ltd Device 4051
02:0a.0 Ethernet controller: Realtek Semiconductor Co., Ltd. RTL-8100/8101L/8139 PCI Fast Ethernet Adapter (rev 10)
Subsystem: Gigabyte Technology Co., Ltd GA-7VM400M/7VT600 Motherboard
Kernel driver in use: 8139too
[/HTML]
===================================================
ifconifg -a
[HTML]eth0 Link encap:Ethernet HWaddr 00:0f:ea:ea:94:ae
UP BROADCAST MULTICAST MTU:1500 Metric:1
RX packets:0 errors:0 dropped:0 overruns:0 frame:0
TX packets:0 errors:0 dropped:0 overruns:0 carrier:0
collisions:0 txqueuelen:1000
RX bytes:0 (0.0 B) TX bytes:0 (0.0 B)
lo Link encap:Local Loopback
inet addr:127.0.0.1 Mask:255.0.0.0
inet6 addr: ::1/128 Scope:Host
UP LOOPBACK RUNNING MTU:65536 Metric:1
RX packets:544 errors:0 dropped:0 overruns:0 frame:0
TX packets:544 errors:0 dropped:0 overruns:0 carrier:0
collisions:0 txqueuelen:0
RX bytes:48874 (48.8 KB) TX bytes:48874 (48.8 KB)
wlan0 Link encap:Ethernet HWaddr 00:60:b3:0e:5f:fd
inet addr:192.168.1.14 Bcast:192.168.1.255 Mask:255.255.255.0
inet6 addr: fe80::260:b3ff:fe0e:5ffd/64 Scope:Link
UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1
RX packets:1915 errors:0 dropped:0 overruns:0 frame:0
TX packets:1963 errors:0 dropped:0 overruns:0 carrier:0
collisions:0 txqueuelen:1000
RX bytes:1379244 (1.3 MB) TX bytes:378917 (378.9 KB)
[/HTML]
==============================================
iwconfig
[HTML]wlan0 IEEE 802.11bg ESSID:"*****************"
Mode:Managed Frequency:2.457 GHz Access Point: ********************
Bit Rate=48 Mb/s Tx-Power=20 dBm
Retry long limit:7 RTS thr
ff Fragment thr ff
Power Management ff
Link Quality=26/100 Signal level=26/100
Rx invalid nwid:0 Rx invalid crypt:0 Rx invalid frag:0
Tx excessive retries:1 Invalid misc:9 Missed beacon:0
lo no wireless extensions.
eth0 no wireless extensions.
[/HTML]
[HTML]cat /etc/network/interfaces
# interfaces(5) file used by ifup(8) and ifdown(8)
auto lo
iface lo inet loopback[/HTML]
[HTML]cat /etc/resolv.conf
# Dynamic resolv.conf(5) file for glibc resolver(3) generated by resolvconf(8)
# DO NOT EDIT THIS FILE BY HAND -- YOUR CHANGES WILL BE OVERWRITTEN
nameserver 127.0.1.1
[/HTML]
Dodatkowo po wpisaniu komendy lsmod | grep zd1211rw, wyskakuje coś takiego
zd1211rw 57580 0
mac80211 545990 1 zd1211rw , co chyba oznacza , że potrzebne sterowniki istniej a w systemie, mimo to nm-applet nie wykrywa żadnej sieci nawet po resecie ;/
=========================================
[HTML]Linux bartek-desktop 3.13.0-24-generic #46-Ubuntu SMP Thu Apr 10 19:08:14 UTC 2014 i686 athlon i686 GNU/Linux
[/HTML]
Wersja architektury systemu:
=========================================
i386
=========================================
lspci -n
[HTML]00:00.0 0600: 10b9:1689
00:01.0 0604: 10b9:5246
00:02.0 0604: 10b9:5249
00:03.0 0601: 10b9:1563 (rev 70)
00:03.1 0680: 10b9:7101
00:04.0 0401: 10b9:5455 (rev 20)
00:0e.0 0101: 10b9:5229 (rev c7)
00:0e.1 0180: 10b9:5289 (rev 10)
00:0f.0 0c03: 10b9:5237 (rev 03)
00:0f.1 0c03: 10b9:5237 (rev 03)
00:0f.2 0c03: 10b9:5237 (rev 03)
00:0f.3 0c03: 10b9:5239 (rev 01)
00:18.0 0600: 1022:1100
00:18.1 0600: 1022:1101
00:18.2 0600: 1022:1102
00:18.3 0600: 1022:1103
01:00.0 0300: 1002:4153
01:00.1 0380: 1002:4173
02:0a.0 0200: 10ec:8139 (rev 10)[/HTML]
======================================
lspci - k
[HTML]00:00.0 Host bridge: ULi Electronics Inc. M1689 K8 Northbridge [Super K8 Single Chip]
Subsystem: Gigabyte Technology Co., Ltd Device 5000
Kernel driver in use: agpgart-amd64
00:01.0 PCI bridge: ULi Electronics Inc. AGP8X Controller
00:02.0 PCI bridge: ULi Electronics Inc. M5249 HTT to PCI Bridge
00:03.0 ISA bridge: ULi Electronics Inc. M1563 HyperTransport South Bridge (rev 70)
Subsystem: Gigabyte Technology Co., Ltd Device 5001
Kernel driver in use: ali1563_smbus
00:03.1 Bridge: ULi Electronics Inc. M7101 Power Management Controller [PMU]
Subsystem: Gigabyte Technology Co., Ltd Device 5003
00:04.0 Multimedia audio controller: ULi Electronics Inc. M5455 PCI AC-Link Controller Audio Device (rev 20)
Subsystem: Gigabyte Technology Co., Ltd Device ae01
Kernel driver in use: snd_intel8x0
00:0e.0 IDE interface: ULi Electronics Inc. M5229 IDE (rev c7)
Subsystem: Gigabyte Technology Co., Ltd Device 5002
Kernel driver in use: pata_ali
00:0e.1 Mass storage controller: ULi Electronics Inc. ULi 5289 SATA (rev 10)
Subsystem: Gigabyte Technology Co., Ltd Device b003
Kernel driver in use: sata_uli
00:0f.0 USB controller: ULi Electronics Inc. USB 1.1 Controller (rev 03)
Subsystem: Gigabyte Technology Co., Ltd Device 5004
Kernel driver in use: ohci-pci
00:0f.1 USB controller: ULi Electronics Inc. USB 1.1 Controller (rev 03)
Subsystem: Gigabyte Technology Co., Ltd Device 5004
Kernel driver in use: ohci-pci
00:0f.2 USB controller: ULi Electronics Inc. USB 1.1 Controller (rev 03)
Subsystem: Gigabyte Technology Co., Ltd Device 5004
Kernel driver in use: ohci-pci
00:0f.3 USB controller: ULi Electronics Inc. USB 2.0 Controller (rev 01)
Subsystem: Gigabyte Technology Co., Ltd Device 5004
Kernel driver in use: ehci-pci
00:18.0 Host bridge: Advanced Micro Devices, Inc. [AMD] K8 [Athlon64/Opteron] HyperTransport Technology Configuration
00:18.1 Host bridge: Advanced Micro Devices, Inc. [AMD] K8 [Athlon64/Opteron] Address Map
00:18.2 Host bridge: Advanced Micro Devices, Inc. [AMD] K8 [Athlon64/Opteron] DRAM Controller
00:18.3 Host bridge: Advanced Micro Devices, Inc. [AMD] K8 [Athlon64/Opteron] Miscellaneous Control
Kernel driver in use: k8temp
01:00.0 VGA compatible controller: Advanced Micro Devices, Inc. [AMD/ATI] RV350 [Radeon 9550]
Subsystem: Gigabyte Technology Co., Ltd Device 4050
Kernel driver in use: radeon
01:00.1 Display controller: Advanced Micro Devices, Inc. [AMD/ATI] RV350 [Radeon 9550] (Secondary)
Subsystem: Gigabyte Technology Co., Ltd Device 4051
02:0a.0 Ethernet controller: Realtek Semiconductor Co., Ltd. RTL-8100/8101L/8139 PCI Fast Ethernet Adapter (rev 10)
Subsystem: Gigabyte Technology Co., Ltd GA-7VM400M/7VT600 Motherboard
Kernel driver in use: 8139too
bartek@bartek-desktop:~$
bartek@bartek-desktop:~$ lspci -k
00:00.0 Host bridge: ULi Electronics Inc. M1689 K8 Northbridge [Super K8 Single Chip]
Subsystem: Gigabyte Technology Co., Ltd Device 5000
Kernel driver in use: agpgart-amd64
00:01.0 PCI bridge: ULi Electronics Inc. AGP8X Controller
00:02.0 PCI bridge: ULi Electronics Inc. M5249 HTT to PCI Bridge
00:03.0 ISA bridge: ULi Electronics Inc. M1563 HyperTransport South Bridge (rev 70)
Subsystem: Gigabyte Technology Co., Ltd Device 5001
Kernel driver in use: ali1563_smbus
00:03.1 Bridge: ULi Electronics Inc. M7101 Power Management Controller [PMU]
Subsystem: Gigabyte Technology Co., Ltd Device 5003
00:04.0 Multimedia audio controller: ULi Electronics Inc. M5455 PCI AC-Link Controller Audio Device (rev 20)
Subsystem: Gigabyte Technology Co., Ltd Device ae01
Kernel driver in use: snd_intel8x0
00:0e.0 IDE interface: ULi Electronics Inc. M5229 IDE (rev c7)
Subsystem: Gigabyte Technology Co., Ltd Device 5002
Kernel driver in use: pata_ali
00:0e.1 Mass storage controller: ULi Electronics Inc. ULi 5289 SATA (rev 10)
Subsystem: Gigabyte Technology Co., Ltd Device b003
Kernel driver in use: sata_uli
00:0f.0 USB controller: ULi Electronics Inc. USB 1.1 Controller (rev 03)
Subsystem: Gigabyte Technology Co., Ltd Device 5004
Kernel driver in use: ohci-pci
00:0f.1 USB controller: ULi Electronics Inc. USB 1.1 Controller (rev 03)
Subsystem: Gigabyte Technology Co., Ltd Device 5004
Kernel driver in use: ohci-pci
00:0f.2 USB controller: ULi Electronics Inc. USB 1.1 Controller (rev 03)
Subsystem: Gigabyte Technology Co., Ltd Device 5004
Kernel driver in use: ohci-pci
00:0f.3 USB controller: ULi Electronics Inc. USB 2.0 Controller (rev 01)
Subsystem: Gigabyte Technology Co., Ltd Device 5004
Kernel driver in use: ehci-pci
00:18.0 Host bridge: Advanced Micro Devices, Inc. [AMD] K8 [Athlon64/Opteron] HyperTransport Technology Configuration
00:18.1 Host bridge: Advanced Micro Devices, Inc. [AMD] K8 [Athlon64/Opteron] Address Map
00:18.2 Host bridge: Advanced Micro Devices, Inc. [AMD] K8 [Athlon64/Opteron] DRAM Controller
00:18.3 Host bridge: Advanced Micro Devices, Inc. [AMD] K8 [Athlon64/Opteron] Miscellaneous Control
Kernel driver in use: k8temp
01:00.0 VGA compatible controller: Advanced Micro Devices, Inc. [AMD/ATI] RV350 [Radeon 9550]
Subsystem: Gigabyte Technology Co., Ltd Device 4050
Kernel driver in use: radeon
01:00.1 Display controller: Advanced Micro Devices, Inc. [AMD/ATI] RV350 [Radeon 9550] (Secondary)
Subsystem: Gigabyte Technology Co., Ltd Device 4051
02:0a.0 Ethernet controller: Realtek Semiconductor Co., Ltd. RTL-8100/8101L/8139 PCI Fast Ethernet Adapter (rev 10)
Subsystem: Gigabyte Technology Co., Ltd GA-7VM400M/7VT600 Motherboard
Kernel driver in use: 8139too
[/HTML]
===================================================
ifconifg -a
[HTML]eth0 Link encap:Ethernet HWaddr 00:0f:ea:ea:94:ae
UP BROADCAST MULTICAST MTU:1500 Metric:1
RX packets:0 errors:0 dropped:0 overruns:0 frame:0
TX packets:0 errors:0 dropped:0 overruns:0 carrier:0
collisions:0 txqueuelen:1000
RX bytes:0 (0.0 B) TX bytes:0 (0.0 B)
lo Link encap:Local Loopback
inet addr:127.0.0.1 Mask:255.0.0.0
inet6 addr: ::1/128 Scope:Host
UP LOOPBACK RUNNING MTU:65536 Metric:1
RX packets:544 errors:0 dropped:0 overruns:0 frame:0
TX packets:544 errors:0 dropped:0 overruns:0 carrier:0
collisions:0 txqueuelen:0
RX bytes:48874 (48.8 KB) TX bytes:48874 (48.8 KB)
wlan0 Link encap:Ethernet HWaddr 00:60:b3:0e:5f:fd
inet addr:192.168.1.14 Bcast:192.168.1.255 Mask:255.255.255.0
inet6 addr: fe80::260:b3ff:fe0e:5ffd/64 Scope:Link
UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1
RX packets:1915 errors:0 dropped:0 overruns:0 frame:0
TX packets:1963 errors:0 dropped:0 overruns:0 carrier:0
collisions:0 txqueuelen:1000
RX bytes:1379244 (1.3 MB) TX bytes:378917 (378.9 KB)
[/HTML]
==============================================
iwconfig
[HTML]wlan0 IEEE 802.11bg ESSID:"*****************"
Mode:Managed Frequency:2.457 GHz Access Point: ********************
Bit Rate=48 Mb/s Tx-Power=20 dBm
Retry long limit:7 RTS thr
ff Fragment thr ffPower Management
ffLink Quality=26/100 Signal level=26/100
Rx invalid nwid:0 Rx invalid crypt:0 Rx invalid frag:0
Tx excessive retries:1 Invalid misc:9 Missed beacon:0
lo no wireless extensions.
eth0 no wireless extensions.
[/HTML]
[HTML]cat /etc/network/interfaces
# interfaces(5) file used by ifup(8) and ifdown(8)
auto lo
iface lo inet loopback[/HTML]
[HTML]cat /etc/resolv.conf
# Dynamic resolv.conf(5) file for glibc resolver(3) generated by resolvconf(8)
# DO NOT EDIT THIS FILE BY HAND -- YOUR CHANGES WILL BE OVERWRITTEN
nameserver 127.0.1.1
[/HTML]
Dodatkowo po wpisaniu komendy lsmod | grep zd1211rw, wyskakuje coś takiego
zd1211rw 57580 0
mac80211 545990 1 zd1211rw , co chyba oznacza , że potrzebne sterowniki istniej a w systemie, mimo to nm-applet nie wykrywa żadnej sieci nawet po resecie ;/
Ten cały CrunchBang jest oparty na wheezy, czy na jessie? Choć w tym przypadku to raczej bez znaczenia. Ściągnij ten pakiet: https://packages.debian.org/wheezy/zd1211-firmware (w tabelce w dziale architektura kliknij w "all").
Instaluje się to w ten sposób (jako root, musisz być w katalogu z pakietem):
Instaluje się to w ten sposób (jako root, musisz być w katalogu z pakietem):
Kod: Zaznacz cały
dpkg -i ./zd1211-firmware_2.21.0.0-1_all.debPokaż wynik:
Kod: Zaznacz cały
dmesgKod: Zaznacz cały
[ 0.000000] Initializing cgroup subsys cpuset
[ 0.000000] Initializing cgroup subsys cpu
[ 0.000000] Linux version 3.2.0-4-486 (debian-kernel@lists.debian.org) (gcc version 4.6.3 (Debian 4.6.3-15) ) #1 Debian 3.2.41-2
[ 0.000000] BIOS-provided physical RAM map:
[ 0.000000] BIOS-e820: 0000000000000000 - 000000000009f800 (usable)
[ 0.000000] BIOS-e820: 000000000009f800 - 00000000000a0000 (reserved)
[ 0.000000] BIOS-e820: 00000000000f0000 - 0000000000100000 (reserved)
[ 0.000000] BIOS-e820: 0000000000100000 - 000000001fff0000 (usable)
[ 0.000000] BIOS-e820: 000000001fff0000 - 000000001fff3000 (ACPI NVS)
[ 0.000000] BIOS-e820: 000000001fff3000 - 0000000020000000 (ACPI data)
[ 0.000000] BIOS-e820: 00000000fec00000 - 00000000fec01000 (reserved)
[ 0.000000] BIOS-e820: 00000000fee00000 - 00000000fee01000 (reserved)
[ 0.000000] BIOS-e820: 00000000ffff0000 - 0000000100000000 (reserved)
[ 0.000000] Notice: NX (Execute Disable) protection cannot be enabled: non-PAE kernel!
[ 0.000000] SMBIOS 2.3 present.
[ 0.000000] DMI: /M1689D, BIOS F3 03/03/2005
[ 0.000000] e820 update range: 0000000000000000 - 0000000000010000 (usable) ==> (reserved)
[ 0.000000] e820 remove range: 00000000000a0000 - 0000000000100000 (usable)
[ 0.000000] last_pfn = 0x1fff0 max_arch_pfn = 0x100000
[ 0.000000] MTRR default type: uncachable
[ 0.000000] MTRR fixed ranges enabled:
[ 0.000000] 00000-9FFFF write-back
[ 0.000000] A0000-BFFFF uncachable
[ 0.000000] C0000-C7FFF write-protect
[ 0.000000] C8000-FFFFF uncachable
[ 0.000000] MTRR variable ranges enabled:
[ 0.000000] 0 base 0000000000 mask FFE0000000 write-back
[ 0.000000] 1 base 00E0000000 mask FFF8000000 write-combining
[ 0.000000] 2 disabled
[ 0.000000] 3 disabled
[ 0.000000] 4 disabled
[ 0.000000] 5 disabled
[ 0.000000] 6 disabled
[ 0.000000] 7 disabled
[ 0.000000] x86 PAT enabled: cpu 0, old 0x7040600070406, new 0x7010600070106
[ 0.000000] found SMP MP-table at [c00f5490] f5490
[ 0.000000] initial memory mapped : 0 - 01800000
[ 0.000000] Base memory trampoline at [c009c000] 9c000 size 12288
[ 0.000000] init_memory_mapping: 0000000000000000-000000001fff0000
[ 0.000000] 0000000000 - 0000400000 page 4k
[ 0.000000] 0000400000 - 001fc00000 page 2M
[ 0.000000] 001fc00000 - 001fff0000 page 4k
[ 0.000000] kernel direct mapping tables up to 1fff0000 @ 17fa000-1800000
[ 0.000000] RAMDISK: 1f429000 - 1ffef000
[ 0.000000] ACPI: RSDP 000f6e80 00014 (v00 AWARD )
[ 0.000000] ACPI: RSDT 1fff3000 0002C (v01 AWARD AWRDACPI 42302E31 AWRD 01010101)
[ 0.000000] ACPI: FACP 1fff3040 00074 (v01 AWARD AWRDACPI 42302E31 AWRD 01010101)
[ 0.000000] ACPI: DSDT 1fff30c0 049E4 (v01 AWARD AWRDACPI 00001003 MSFT 0100000C)
[ 0.000000] ACPI: FACS 1fff0000 00040
[ 0.000000] ACPI: APIC 1fff7ac0 0005A (v01 AWARD AWRDACPI 42302E31 AWRD 01010101)
[ 0.000000] ACPI: Local APIC address 0xfee00000
[ 0.000000] 0MB HIGHMEM available.
[ 0.000000] 511MB LOWMEM available.
[ 0.000000] mapped low ram: 0 - 1fff0000
[ 0.000000] low ram: 0 - 1fff0000
[ 0.000000] Zone PFN ranges:
[ 0.000000] DMA 0x00000010 -> 0x00001000
[ 0.000000] Normal 0x00001000 -> 0x0001fff0
[ 0.000000] HighMem empty
[ 0.000000] Movable zone start PFN for each node
[ 0.000000] early_node_map[2] active PFN ranges
[ 0.000000] 0: 0x00000010 -> 0x0000009f
[ 0.000000] 0: 0x00000100 -> 0x0001fff0
[ 0.000000] On node 0 totalpages: 130943
[ 0.000000] free_area_init_node: node 0, pgdat c13c5938, node_mem_map df029200
[ 0.000000] DMA zone: 32 pages used for memmap
[ 0.000000] DMA zone: 0 pages reserved
[ 0.000000] DMA zone: 3951 pages, LIFO batch:0
[ 0.000000] Normal zone: 992 pages used for memmap
[ 0.000000] Normal zone: 125968 pages, LIFO batch:31
[ 0.000000] Using APIC driver default
[ 0.000000] ACPI: PM-Timer IO Port: 0x1008
[ 0.000000] ACPI: Local APIC address 0xfee00000
[ 0.000000] ACPI: LAPIC (acpi_id[0x00] lapic_id[0x00] enabled)
[ 0.000000] ACPI: LAPIC_NMI (acpi_id[0x00] dfl dfl lint[0x1])
[ 0.000000] ACPI: IOAPIC (id[0x02] address[0xfec00000] gsi_base[0])
[ 0.000000] IOAPIC[0]: apic_id 2, version 17, address 0xfec00000, GSI 0-23
[ 0.000000] ACPI: INT_SRC_OVR (bus 0 bus_irq 0 global_irq 2 dfl dfl)
[ 0.000000] ACPI: INT_SRC_OVR (bus 0 bus_irq 9 global_irq 9 low level)
[ 0.000000] ACPI: IRQ0 used by override.
[ 0.000000] ACPI: IRQ2 used by override.
[ 0.000000] ACPI: IRQ9 used by override.
[ 0.000000] Using ACPI (MADT) for SMP configuration information
[ 0.000000] nr_irqs_gsi: 40
[ 0.000000] PM: Registered nosave memory: 000000000009f000 - 00000000000a0000
[ 0.000000] PM: Registered nosave memory: 00000000000a0000 - 00000000000f0000
[ 0.000000] PM: Registered nosave memory: 00000000000f0000 - 0000000000100000
[ 0.000000] Allocating PCI resources starting at 20000000 (gap: 20000000:dec00000)
[ 0.000000] Booting paravirtualized kernel on bare hardware
[ 0.000000] pcpu-alloc: s0 r0 d32768 u32768 alloc=1*32768
[ 0.000000] pcpu-alloc: [0] 0
[ 0.000000] Built 1 zonelists in Zone order, mobility grouping on. Total pages: 129919
[ 0.000000] Kernel command line: initrd=/live/initrd.img boot=live config quiet BOOT_IMAGE=/live/vmlinuz
[ 0.000000] PID hash table entries: 2048 (order: 1, 8192 bytes)
[ 0.000000] Dentry cache hash table entries: 65536 (order: 6, 262144 bytes)
[ 0.000000] Inode-cache hash table entries: 32768 (order: 5, 131072 bytes)
[ 0.000000] Initializing CPU#0
[ 0.000000] Initializing HighMem for node 0 (00000000:00000000)
[ 0.000000] Memory: 502292k/524224k available (2590k kernel code, 21480k reserved, 1299k data, 452k init, 0k highmem)
[ 0.000000] virtual kernel memory layout:
[ 0.000000] fixmap : 0xfffa1000 - 0xfffff000 ( 376 kB)
[ 0.000000] pkmap : 0xff800000 - 0xffc00000 (4096 kB)
[ 0.000000] vmalloc : 0xe07f0000 - 0xff7fe000 ( 496 MB)
[ 0.000000] lowmem : 0xc0000000 - 0xdfff0000 ( 511 MB)
[ 0.000000] .init : 0xc13cd000 - 0xc143e000 ( 452 kB)
[ 0.000000] .data : 0xc12878ec - 0xc13cc580 (1299 kB)
[ 0.000000] .text : 0xc1000000 - 0xc12878ec (2590 kB)
[ 0.000000] Checking if this processor honours the WP bit even in supervisor mode...Ok.
[ 0.000000] NR_IRQS:2304 nr_irqs:256 16
[ 0.000000] CPU 0 irqstacks, hard=de808000 soft=de80a000
[ 0.000000] Console: colour VGA+ 80x25
[ 0.000000] console [tty0] enabled
[ 0.000000] Fast TSC calibration using PIT
[ 0.000000] Detected 2009.965 MHz processor.
[ 0.008002] Calibrating delay loop (skipped), value calculated using timer frequency.. 4019.93 BogoMIPS (lpj=8039860)
[ 0.008007] pid_max: default: 32768 minimum: 301
[ 0.008042] Security Framework initialized
[ 0.008049] AppArmor: AppArmor disabled by boot time parameter
[ 0.008061] Mount-cache hash table entries: 512
[ 0.008162] Initializing cgroup subsys cpuacct
[ 0.008166] Initializing cgroup subsys memory
[ 0.008174] Initializing cgroup subsys devices
[ 0.008176] Initializing cgroup subsys freezer
[ 0.008179] Initializing cgroup subsys net_cls
[ 0.008182] Initializing cgroup subsys blkio
[ 0.008188] Initializing cgroup subsys perf_event
[ 0.008218] CPU: AMD Athlon(tm) 64 Processor 3000+ stepping 0a
[ 0.008556] ACPI: Core revision 20110623
[ 0.010533] Performance Events: AMD PMU driver.
[ 0.010540] ... version: 0
[ 0.010542] ... bit width: 48
[ 0.010544] ... generic registers: 4
[ 0.010546] ... value mask: 0000ffffffffffff
[ 0.010548] ... max period: 00007fffffffffff
[ 0.010550] ... fixed-purpose events: 0
[ 0.010552] ... event mask: 000000000000000f
[ 0.010708] NMI watchdog enabled, takes one hw-pmu counter.
[ 0.010728] Enabling APIC mode: Flat. Using 1 I/O APICs
[ 0.012391] ..TIMER: vector=0x30 apic1=0 pin1=2 apic2=-1 pin2=-1
[ 0.056003] devtmpfs: initialized
[ 0.056003] PM: Registering ACPI NVS region at 1fff0000 (12288 bytes)
[ 0.056003] print_constraints: dummy:
[ 0.056003] NET: Registered protocol family 16
[ 0.056003] EISA bus registered
[ 0.056003] node 0 link 0: io port [1000, fffff]
[ 0.056003] TOM: 0000000020000000 aka 512M
[ 0.056003] node 0 link 0: mmio [a0000, bffff]
[ 0.056003] node 0 link 0: mmio [20000000, ffb7ffff]
[ 0.056003] bus: [00, ff] on node 0 link 0
[ 0.056003] bus: 00 index 0 [io 0x0000-0xffff]
[ 0.056003] bus: 00 index 1 [mem 0x000a0000-0x000bffff]
[ 0.056003] bus: 00 index 2 [mem 0x20000000-0xffffffff]
[ 0.056003] ACPI: bus type pci registered
[ 0.075882] PCI: PCI BIOS revision 2.10 entry at 0xfb7a0, last bus=2
[ 0.075885] PCI: Using configuration type 1 for base access
[ 0.076675] bio: create slab <bio-0> at 0
[ 0.076743] ACPI: Added _OSI(Module Device)
[ 0.076746] ACPI: Added _OSI(Processor Device)
[ 0.076749] ACPI: Added _OSI(3.0 _SCP Extensions)
[ 0.076751] ACPI: Added _OSI(Processor Aggregator Device)
[ 0.077249] ACPI: EC: Look up EC in DSDT
[ 0.077811] ACPI: Actual Package length (6) is larger than NumElements field (3), truncated
[ 0.077815]
[ 0.079987] ACPI: Interpreter enabled
[ 0.079995] ACPI: (supports S0 S1 S4 S5)
[ 0.080029] ACPI: Using IOAPIC for interrupt routing
[ 0.083314] ACPI: No dock devices found.
[ 0.083316] HEST: Table not found.
[ 0.083321] PCI: Ignoring host bridge windows from ACPI; if necessary, use "pci=use_crs" and report a bug
[ 0.083380] ACPI: PCI Root Bridge [PCI0] (domain 0000 [bus 00-ff])
[ 0.083498] pci_root PNP0A03:00: host bridge window [io 0x0000-0x0cf7] (ignored)
[ 0.083501] pci_root PNP0A03:00: host bridge window [io 0x0d00-0xffff] (ignored)
[ 0.083505] pci_root PNP0A03:00: host bridge window [mem 0x000a0000-0x000bffff] (ignored)
[ 0.083508] pci_root PNP0A03:00: host bridge window [mem 0x000c0000-0x000dffff] (ignored)
[ 0.083511] pci_root PNP0A03:00: host bridge window [mem 0x20000000-0xfebfffff] (ignored)
[ 0.083531] pci 0000:00:00.0: [10b9:1689] type 0 class 0x000600
[ 0.083541] pci 0000:00:00.0: reg 10: [mem 0xe0000000-0xe7ffffff pref]
[ 0.083605] pci 0000:00:01.0: [10b9:5246] type 1 class 0x000604
[ 0.083637] pci 0000:00:02.0: [10b9:5249] type 1 class 0x000604
[ 0.083668] pci 0000:00:03.0: [10b9:1563] type 0 class 0x000601
[ 0.083719] pci 0000:00:03.1: [10b9:7101] type 0 class 0x000680
[ 0.083764] pci 0000:00:03.1: quirk: [io 0x1000-0x103f] claimed by ali7101 ACPI
[ 0.083786] pci 0000:00:04.0: [10b9:5455] type 0 class 0x000401
[ 0.083799] pci 0000:00:04.0: reg 10: [io 0xb000-0xb0ff]
[ 0.083807] pci 0000:00:04.0: reg 14: [mem 0xfa100000-0xfa100fff]
[ 0.083850] pci 0000:00:04.0: supports D1 D2
[ 0.083853] pci 0000:00:04.0: PME# supported from D2 D3hot D3cold
[ 0.083874] pci 0000:00:0e.0: [10b9:5229] type 0 class 0x000101
[ 0.083882] pci 0000:00:0e.0: reg 10: [io 0x01f0-0x01ff]
[ 0.083888] pci 0000:00:0e.0: reg 14: [io 0x03f4-0x03f7]
[ 0.083894] pci 0000:00:0e.0: reg 18: [io 0x0170-0x017f]
[ 0.083899] pci 0000:00:0e.0: reg 1c: [io 0x0374-0x0377]
[ 0.083905] pci 0000:00:0e.0: reg 20: [io 0xf000-0xf00f]
[ 0.083925] pci 0000:00:0e.1: [10b9:5289] type 0 class 0x000180
[ 0.083933] pci 0000:00:0e.1: reg 10: [io 0xb400-0xb407]
[ 0.083938] pci 0000:00:0e.1: reg 14: [io 0xb800-0xb803]
[ 0.083944] pci 0000:00:0e.1: reg 18: [io 0xbc00-0xbc07]
[ 0.083950] pci 0000:00:0e.1: reg 1c: [io 0xc000-0xc003]
[ 0.083955] pci 0000:00:0e.1: reg 20: [io 0xc400-0xc40f]
[ 0.083978] pci 0000:00:0f.0: [10b9:5237] type 0 class 0x000c03
[ 0.083986] pci 0000:00:0f.0: reg 10: [mem 0xfa101000-0xfa101fff]
[ 0.084025] pci 0000:00:0f.1: [10b9:5237] type 0 class 0x000c03
[ 0.084032] pci 0000:00:0f.1: reg 10: [mem 0xfa102000-0xfa102fff]
[ 0.084063] pci 0000:00:0f.2: [10b9:5237] type 0 class 0x000c03
[ 0.084071] pci 0000:00:0f.2: reg 10: [mem 0xfa103000-0xfa103fff]
[ 0.084104] pci 0000:00:0f.3: [10b9:5239] type 0 class 0x000c03
[ 0.084114] pci 0000:00:0f.3: reg 10: [mem 0xfa104000-0xfa1040ff]
[ 0.084148] pci 0000:00:0f.3: PME# supported from D0 D3hot D3cold
[ 0.084170] pci 0000:00:18.0: [1022:1100] type 0 class 0x000600
[ 0.084191] pci 0000:00:18.1: [1022:1101] type 0 class 0x000600
[ 0.084207] pci 0000:00:18.2: [1022:1102] type 0 class 0x000600
[ 0.084224] pci 0000:00:18.3: [1022:1103] type 0 class 0x000600
[ 0.084242] PCI: peer root bus 00 res updated from pci conf
[ 0.084264] pci 0000:01:00.0: [1002:4153] type 0 class 0x000300
[ 0.084277] pci 0000:01:00.0: reg 10: [mem 0xe8000000-0xefffffff pref]
[ 0.084284] pci 0000:01:00.0: reg 14: [io 0x9000-0x90ff]
[ 0.084291] pci 0000:01:00.0: reg 18: [mem 0xf9000000-0xf900ffff]
[ 0.084310] pci 0000:01:00.0: reg 30: [mem 0x00000000-0x0001ffff pref]
[ 0.084332] pci 0000:01:00.0: supports D1 D2
[ 0.084347] pci 0000:01:00.1: [1002:4173] type 0 class 0x000380
[ 0.084357] pci 0000:01:00.1: reg 10: [mem 0xf0000000-0xf7ffffff pref]
[ 0.084364] pci 0000:01:00.1: reg 14: [mem 0xf9010000-0xf901ffff]
[ 0.084401] pci 0000:01:00.1: supports D1 D2
[ 0.084431] pci 0000:00:01.0: PCI bridge to [bus 01-01]
[ 0.084435] pci 0000:00:01.0: bridge window [io 0x9000-0x9fff]
[ 0.084440] pci 0000:00:01.0: bridge window [mem 0xf8000000-0xf9ffffff]
[ 0.084444] pci 0000:00:01.0: bridge window [mem 0xe8000000-0xf7ffffff pref]
[ 0.084473] pci 0000:02:0a.0: [10ec:8139] type 0 class 0x000200
[ 0.084485] pci 0000:02:0a.0: reg 10: [io 0xa000-0xa0ff]
[ 0.084493] pci 0000:02:0a.0: reg 14: [mem 0xfa000000-0xfa0000ff]
[ 0.084538] pci 0000:02:0a.0: supports D1 D2
[ 0.084540] pci 0000:02:0a.0: PME# supported from D1 D2 D3hot D3cold
[ 0.084565] pci 0000:00:02.0: PCI bridge to [bus 02-02] (subtractive decode)
[ 0.084569] pci 0000:00:02.0: bridge window [io 0xa000-0xafff]
[ 0.084574] pci 0000:00:02.0: bridge window [mem 0xfa000000-0xfa0fffff]
[ 0.084578] pci 0000:00:02.0: bridge window [io 0x0000-0xffff] (subtractive decode)
[ 0.084581] pci 0000:00:02.0: bridge window [mem 0x000a0000-0x000bffff] (subtractive decode)
[ 0.084585] pci 0000:00:02.0: bridge window [mem 0x20000000-0xffffffff] (subtractive decode)
[ 0.084595] pci_bus 0000:00: on NUMA node 0
[ 0.084599] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0._PRT]
[ 0.084687] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.P2PB._PRT]
[ 0.084818] pci0000:00: Unable to request _OSC control (_OSC support mask: 0x1e)
[ 0.098944] ACPI: PCI Interrupt Link [LNK1] (IRQs 1 3 4 5 6 7 10 11 *12 14 15)
[ 0.099077] ACPI: PCI Interrupt Link [LNK2] (IRQs 1 3 4 5 6 7 10 11 12 14 15) *0, disabled.
[ 0.099210] ACPI: PCI Interrupt Link [LNK3] (IRQs 1 3 4 5 6 7 *10 11 12 14 15)
[ 0.099394] ACPI: PCI Interrupt Link [LNK4] (IRQs 1 3 4 5 6 7 10 *11 12 14 15)
[ 0.099579] ACPI: PCI Interrupt Link [LNK5] (IRQs 1 3 4 5 6 7 10 11 *12 14 15)
[ 0.099763] ACPI: PCI Interrupt Link [LNK6] (IRQs 1 3 4 5 6 7 *10 11 12 14 15)
[ 0.099948] ACPI: PCI Interrupt Link [LNK7] (IRQs 1 3 4 5 6 7 10 *11 12 14 15)
[ 0.100136] ACPI: PCI Interrupt Link [LNK8] (IRQs 1 3 4 *5 6 7 10 11 12 14 15)
[ 0.100265] ACPI: PCI Interrupt Link [LNK9] (IRQs 1 3 4 5 6 7 10 11 12 14 15) *0, disabled.
[ 0.100390] vgaarb: device added: PCI:0000:01:00.0,decodes=io+mem,owns=io+mem,locks=none
[ 0.100394] vgaarb: loaded
[ 0.100396] vgaarb: bridge control possible 0000:01:00.0
[ 0.100457] PCI: Using ACPI for IRQ routing
[ 0.100461] PCI: pci_cache_line_size set to 64 bytes
[ 0.100509] reserve RAM buffer: 000000000009f800 - 000000000009ffff
[ 0.100513] reserve RAM buffer: 000000001fff0000 - 000000001fffffff
[ 0.102045] pnp: PnP ACPI init
[ 0.102066] ACPI: bus type pnp registered
[ 0.102250] pnp 00:00: [mem 0x000f0000-0x000f3fff]
[ 0.102253] pnp 00:00: [mem 0x000f4000-0x000f7fff]
[ 0.102256] pnp 00:00: [mem 0x000f8000-0x000fbfff]
[ 0.102259] pnp 00:00: [mem 0x000fc000-0x000fffff]
[ 0.102261] pnp 00:00: [mem 0x1fff0000-0x1fffffff]
[ 0.102264] pnp 00:00: [mem 0xffff0000-0xffffffff]
[ 0.102267] pnp 00:00: [mem 0x00000000-0x0009ffff]
[ 0.102270] pnp 00:00: [mem 0x00100000-0x1ffeffff]
[ 0.102273] pnp 00:00: [mem 0xfec00000-0xfec00fff]
[ 0.102275] pnp 00:00: [mem 0xfee00000-0xfee00fff]
[ 0.102348] system 00:00: [mem 0x000f0000-0x000f3fff] could not be reserved
[ 0.102352] system 00:00: [mem 0x000f4000-0x000f7fff] could not be reserved
[ 0.102356] system 00:00: [mem 0x000f8000-0x000fbfff] could not be reserved
[ 0.102359] system 00:00: [mem 0x000fc000-0x000fffff] could not be reserved
[ 0.102363] system 00:00: [mem 0x1fff0000-0x1fffffff] could not be reserved
[ 0.102367] system 00:00: [mem 0xffff0000-0xffffffff] has been reserved
[ 0.102371] system 00:00: [mem 0x00000000-0x0009ffff] could not be reserved
[ 0.102374] system 00:00: [mem 0x00100000-0x1ffeffff] could not be reserved
[ 0.102378] system 00:00: [mem 0xfec00000-0xfec00fff] could not be reserved
[ 0.102382] system 00:00: [mem 0xfee00000-0xfee00fff] has been reserved
[ 0.102386] system 00:00: Plug and Play ACPI device, IDs PNP0c01 (active)
[ 0.102444] pnp 00:01: [bus 00-ff]
[ 0.102448] pnp 00:01: [io 0x0cf8-0x0cff]
[ 0.102450] pnp 00:01: [io 0x0000-0x0cf7 window]
[ 0.102453] pnp 00:01: [io 0x0d00-0xffff window]
[ 0.102456] pnp 00:01: [io 0x1400-0x141f]
[ 0.102459] pnp 00:01: [io 0x1000-0x107f]
[ 0.102461] pnp 00:01: [io 0x04d6]
[ 0.102464] pnp 00:01: [mem 0x000a0000-0x000bffff window]
[ 0.102467] pnp 00:01: [mem 0x000c0000-0x000dffff window]
[ 0.102470] pnp 00:01: [mem 0x20000000-0xfebfffff window]
[ 0.102520] pnp 00:01: Plug and Play ACPI device, IDs PNP0a03 (active)
[ 0.102734] pnp 00:02: [io 0x0010-0x001f]
[ 0.102737] pnp 00:02: [io 0x0022-0x003f]
[ 0.102739] pnp 00:02: [io 0x0044-0x005f]
[ 0.102742] pnp 00:02: [io 0x0062-0x0063]
[ 0.102744] pnp 00:02: [io 0x0065-0x006f]
[ 0.102747] pnp 00:02: [io 0x0074-0x007f]
[ 0.102750] pnp 00:02: [io 0x0091-0x0093]
[ 0.102752] pnp 00:02: [io 0x00a2-0x00bf]
[ 0.102755] pnp 00:02: [io 0x00e0-0x00ef]
[ 0.102757] pnp 00:02: [io 0x04d0-0x04d1]
[ 0.102760] pnp 00:02: [io 0x0800-0x087f]
[ 0.102812] system 00:02: [io 0x04d0-0x04d1] has been reserved
[ 0.102816] system 00:02: [io 0x0800-0x087f] has been reserved
[ 0.102820] system 00:02: Plug and Play ACPI device, IDs PNP0c02 (active)
[ 0.102833] pnp 00:03: [dma 4]
[ 0.102835] pnp 00:03: [io 0x0000-0x000f]
[ 0.102838] pnp 00:03: [io 0x0080-0x0090]
[ 0.102840] pnp 00:03: [io 0x0094-0x009f]
[ 0.102843] pnp 00:03: [io 0x00c0-0x00df]
[ 0.102876] pnp 00:03: Plug and Play ACPI device, IDs PNP0200 (active)
[ 0.102888] pnp 00:04: [io 0x0070-0x0073]
[ 0.102904] pnp 00:04: [irq 8]
[ 0.102936] pnp 00:04: Plug and Play ACPI device, IDs PNP0b00 (active)
[ 0.102945] pnp 00:05: [io 0x0061]
[ 0.102977] pnp 00:05: Plug and Play ACPI device, IDs PNP0800 (active)
[ 0.102987] pnp 00:06: [io 0x00f0-0x00ff]
[ 0.102992] pnp 00:06: [irq 13]
[ 0.103027] pnp 00:06: Plug and Play ACPI device, IDs PNP0c04 (active)
[ 0.103099] pnp 00:07: [io 0x03f0-0x03f5]
[ 0.103101] pnp 00:07: [io 0x03f7]
[ 0.103106] pnp 00:07: [irq 6]
[ 0.103109] pnp 00:07: [dma 2]
[ 0.103159] pnp 00:07: Plug and Play ACPI device, IDs PNP0700 (active)
[ 0.103290] pnp 00:08: [io 0x03f8-0x03ff]
[ 0.103295] pnp 00:08: [irq 4]
[ 0.103349] pnp 00:08: Plug and Play ACPI device, IDs PNP0501 (active)
[ 0.103493] pnp 00:09: [io 0x02f8-0x02ff]
[ 0.103498] pnp 00:09: [irq 3]
[ 0.103549] pnp 00:09: Plug and Play ACPI device, IDs PNP0501 (active)
[ 0.103734] pnp 00:0a: [io 0x0378-0x037f]
[ 0.103739] pnp 00:0a: [irq 7]
[ 0.103787] pnp 00:0a: Plug and Play ACPI device, IDs PNP0400 (active)
[ 0.103860] pnp 00:0b: [io 0x0060]
[ 0.103862] pnp 00:0b: [io 0x0064]
[ 0.103867] pnp 00:0b: [irq 1]
[ 0.103903] pnp 00:0b: Plug and Play ACPI device, IDs PNP0303 (active)
[ 0.104042] pnp 00:0c: [io 0x0201]
[ 0.104087] pnp 00:0c: Plug and Play ACPI device, IDs PNPb02f (active)
[ 0.104139] pnp: PnP ACPI: found 13 devices
[ 0.104141] ACPI: ACPI bus type pnp unregistered
[ 0.104146] PnPBIOS: Disabled by ACPI PNP
[ 0.140747] Switching to clocksource acpi_pm
[ 0.140762] PCI: max bus depth: 1 pci_try_num: 2
[ 0.140782] pci 0000:01:00.0: BAR 6: assigned [mem 0xf8000000-0xf801ffff pref]
[ 0.140787] pci 0000:00:01.0: PCI bridge to [bus 01-01]
[ 0.140790] pci 0000:00:01.0: bridge window [io 0x9000-0x9fff]
[ 0.140796] pci 0000:00:01.0: bridge window [mem 0xf8000000-0xf9ffffff]
[ 0.140800] pci 0000:00:01.0: bridge window [mem 0xe8000000-0xf7ffffff pref]
[ 0.140806] pci 0000:00:02.0: PCI bridge to [bus 02-02]
[ 0.140810] pci 0000:00:02.0: bridge window [io 0xa000-0xafff]
[ 0.140815] pci 0000:00:02.0: bridge window [mem 0xfa000000-0xfa0fffff]
[ 0.140827] pci 0000:00:01.0: setting latency timer to 64
[ 0.140833] pci 0000:00:02.0: setting latency timer to 64
[ 0.140838] pci_bus 0000:00: resource 4 [io 0x0000-0xffff]
[ 0.140841] pci_bus 0000:00: resource 5 [mem 0x000a0000-0x000bffff]
[ 0.140844] pci_bus 0000:00: resource 6 [mem 0x20000000-0xffffffff]
[ 0.140847] pci_bus 0000:01: resource 0 [io 0x9000-0x9fff]
[ 0.140850] pci_bus 0000:01: resource 1 [mem 0xf8000000-0xf9ffffff]
[ 0.140853] pci_bus 0000:01: resource 2 [mem 0xe8000000-0xf7ffffff pref]
[ 0.140857] pci_bus 0000:02: resource 0 [io 0xa000-0xafff]
[ 0.140860] pci_bus 0000:02: resource 1 [mem 0xfa000000-0xfa0fffff]
[ 0.140863] pci_bus 0000:02: resource 4 [io 0x0000-0xffff]
[ 0.140866] pci_bus 0000:02: resource 5 [mem 0x000a0000-0x000bffff]
[ 0.140869] pci_bus 0000:02: resource 6 [mem 0x20000000-0xffffffff]
[ 0.140916] NET: Registered protocol family 2
[ 0.140981] IP route cache hash table entries: 4096 (order: 2, 16384 bytes)
[ 0.141179] TCP established hash table entries: 16384 (order: 5, 131072 bytes)
[ 0.141307] TCP bind hash table entries: 16384 (order: 4, 65536 bytes)
[ 0.141379] TCP: Hash tables configured (established 16384 bind 16384)
[ 0.141382] TCP reno registered
[ 0.141385] UDP hash table entries: 256 (order: 0, 4096 bytes)
[ 0.141392] UDP-Lite hash table entries: 256 (order: 0, 4096 bytes)
[ 0.141447] NET: Registered protocol family 1
[ 0.141484] PCI: CLS mismatch (32 != 512), using 64 bytes
[ 0.356035] pci 0000:01:00.0: Boot video device
[ 0.356103] Unpacking initramfs...
[ 0.731921] Freeing initrd memory: 12056k freed
[ 0.745082] audit: initializing netlink socket (disabled)
[ 0.745099] type=2000 audit(1407159863.744:1): initialized
[ 0.761765] HugeTLB registered 4 MB page size, pre-allocated 0 pages
[ 0.761862] VFS: Disk quotas dquot_6.5.2
[ 0.761880] Dquot-cache hash table entries: 1024 (order 0, 4096 bytes)
[ 0.761934] msgmni has been set to 1004
[ 0.762090] alg: No test for stdrng (krng)
[ 0.762112] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 253)
[ 0.762116] io scheduler noop registered
[ 0.762118] io scheduler deadline registered
[ 0.762126] io scheduler cfq registered (default)
[ 0.762251] pci_hotplug: PCI Hot Plug PCI Core version: 0.5
[ 0.762278] pciehp: PCI Express Hot Plug Controller Driver version: 0.4
[ 0.762281] acpiphp: ACPI Hot Plug PCI Controller Driver version: 0.5
[ 0.762610] ERST: Table is not found!
[ 0.762612] GHES: HEST is not enabled!
[ 0.762625] isapnp: Scanning for PnP cards...
[ 1.115978] isapnp: No Plug & Play device found
[ 1.116048] Serial: 8250/16550 driver, 4 ports, IRQ sharing enabled
[ 1.136346] serial8250: ttyS0 at I/O 0x3f8 (irq = 4) is a 16550A
[ 1.156655] serial8250: ttyS1 at I/O 0x2f8 (irq = 3) is a 16550A
[ 1.177166] 00:08: ttyS0 at I/O 0x3f8 (irq = 4) is a 16550A
[ 1.197505] 00:09: ttyS1 at I/O 0x2f8 (irq = 3) is a 16550A
[ 1.197696] Linux agpgart interface v0.103
[ 1.197713] agpgart-ali 0000:00:00.0: unsupported ALi chipset [10b9/1689])
[ 1.197800] agpgart-amd64 0000:00:00.0: AGP bridge [10b9/1689]
[ 1.197807] agpgart-amd64 0000:00:00.0: aperture size 4096 MB is not right, using settings from NB
[ 1.197812] agpgart-amd64 0000:00:00.0: setting up ULi AGP
[ 1.203697] agpgart-amd64 0000:00:00.0: AGP aperture is 128M @ 0xe0000000
[ 1.203897] i8042: PNP: PS/2 Controller [PNP0303:PS2K] at 0x60,0x64 irq 1
[ 1.203900] i8042: PNP: PS/2 appears to have AUX port disabled, if this is incorrect please boot with i8042.nopnp
[ 1.204775] serio: i8042 KBD port at 0x60,0x64 irq 1
[ 1.204884] mousedev: PS/2 mouse device common for all mice
[ 1.204930] rtc_cmos 00:04: RTC can wake from S4
[ 1.205019] rtc_cmos 00:04: rtc core: registered rtc_cmos as rtc0
[ 1.205036] rtc0: alarms up to one month, 242 bytes nvram
[ 1.205094] EISA: Probing bus 0 at eisa.0
[ 1.205098] EISA: Cannot allocate resource for mainboard
[ 1.205101] Cannot allocate resource for EISA slot 1
[ 1.205104] Cannot allocate resource for EISA slot 2
[ 1.205106] Cannot allocate resource for EISA slot 3
[ 1.205109] Cannot allocate resource for EISA slot 4
[ 1.205111] Cannot allocate resource for EISA slot 5
[ 1.205114] Cannot allocate resource for EISA slot 6
[ 1.205117] Cannot allocate resource for EISA slot 7
[ 1.205119] Cannot allocate resource for EISA slot 8
[ 1.205121] EISA: Detected 0 cards.
[ 1.205124] cpuidle: using governor ladder
[ 1.205126] cpuidle: using governor menu
[ 1.205343] TCP cubic registered
[ 1.205366] NET: Registered protocol family 10
[ 1.205836] Mobile IPv6
[ 1.205838] NET: Registered protocol family 17
[ 1.205843] Registering the dns_resolver key type
[ 1.205857] Using IPI Shortcut mode
[ 1.205951] PM: Hibernation image not present or could not be loaded.
[ 1.205962] registered taskstats version 1
[ 1.206156] rtc_cmos 00:04: setting system clock to 2014-08-04 13:44:24 UTC (1407159864)
[ 1.206199] Initializing network drop monitor service
[ 1.206315] Freeing unused kernel memory: 452k freed
[ 1.206702] Write protecting the kernel text: 2592k
[ 1.206721] Write protecting the kernel read-only data: 1040k
[ 1.222754] udevd[42]: starting version 175
[ 1.235680] input: AT Translated Set 2 keyboard as /devices/platform/i8042/serio0/input/input0
[ 1.341544] 8139cp: 8139cp: 10/100 PCI Ethernet driver v1.3 (Mar 22, 2004)
[ 1.341574] 8139cp 0000:02:0a.0: This (id 10ec:8139 rev 10) is not an 8139C+ compatible chip, use 8139too
[ 1.342031] 8139too: 8139too Fast Ethernet driver 0.9.28
[ 1.342861] 8139too 0000:02:0a.0: eth0: RealTek RTL8139 at 0xa000, 00:0f:ea:ea:94:ae, IRQ 18
[ 1.357698] Floppy drive(s): fd0 is 1.44M
[ 1.372559] SCSI subsystem initialized
[ 1.389374] usbcore: registered new interface driver usbfs
[ 1.389405] usbcore: registered new interface driver hub
[ 1.411044] usbcore: registered new device driver usb
[ 1.411637] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
[ 1.411689] ehci_hcd 0000:00:0f.3: EHCI Host Controller
[ 1.411711] ehci_hcd 0000:00:0f.3: new USB bus registered, assigned bus number 1
[ 1.411739] ehci_hcd 0000:00:0f.3: debug port 1
[ 1.415831] FDC 0 is a post-1991 82077
[ 1.432049] ehci_hcd 0000:00:0f.3: irq 23, io mem 0xfa104000
[ 1.433395] ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver
[ 1.442731] libata version 3.00 loaded.
[ 1.444033] ehci_hcd 0000:00:0f.3: USB 2.0 started, EHCI 1.00
[ 1.444067] usb usb1: New USB device found, idVendor=1d6b, idProduct=0002
[ 1.444071] usb usb1: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[ 1.444074] usb usb1: Product: EHCI Host Controller
[ 1.444076] usb usb1: Manufacturer: Linux 3.2.0-4-486 ehci_hcd
[ 1.444079] usb usb1: SerialNumber: 0000:00:0f.3
[ 1.444226] hub 1-0:1.0: USB hub found
[ 1.444233] hub 1-0:1.0: 8 ports detected
[ 1.445016] ohci_hcd 0000:00:0f.0: OHCI Host Controller
[ 1.445029] ohci_hcd 0000:00:0f.0: new USB bus registered, assigned bus number 2
[ 1.445060] ohci_hcd 0000:00:0f.0: irq 20, io mem 0xfa101000
[ 1.502039] usb usb2: New USB device found, idVendor=1d6b, idProduct=0001
[ 1.502044] usb usb2: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[ 1.502047] usb usb2: Product: OHCI Host Controller
[ 1.502050] usb usb2: Manufacturer: Linux 3.2.0-4-486 ohci_hcd
[ 1.502052] usb usb2: SerialNumber: 0000:00:0f.0
[ 1.502305] hub 2-0:1.0: USB hub found
[ 1.502312] hub 2-0:1.0: 3 ports detected
[ 1.502967] scsi0 : pata_ali
[ 1.503104] scsi1 : pata_ali
[ 1.503585] ata1: PATA max UDMA/133 cmd 0x1f0 ctl 0x3f6 bmdma 0xf000 irq 14
[ 1.503589] ata2: PATA max UDMA/133 cmd 0x170 ctl 0x376 bmdma 0xf008 irq 15
[ 1.503734] sata_uli 0000:00:0e.1: version 1.3
[ 1.504321] scsi2 : sata_uli
[ 1.504542] scsi3 : sata_uli
[ 1.504599] ata3: SATA max UDMA/133 cmd 0xb400 ctl 0xb800 bmdma 0xc400 irq 19
[ 1.504602] ata4: SATA max UDMA/133 cmd 0xbc00 ctl 0xc000 bmdma 0xc408 irq 19
[ 1.504729] ohci_hcd 0000:00:0f.1: OHCI Host Controller
[ 1.504744] ohci_hcd 0000:00:0f.1: new USB bus registered, assigned bus number 3
[ 1.504767] ohci_hcd 0000:00:0f.1: irq 21, io mem 0xfa102000
[ 1.562019] usb usb3: New USB device found, idVendor=1d6b, idProduct=0001
[ 1.562023] usb usb3: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[ 1.562026] usb usb3: Product: OHCI Host Controller
[ 1.562028] usb usb3: Manufacturer: Linux 3.2.0-4-486 ohci_hcd
[ 1.562031] usb usb3: SerialNumber: 0000:00:0f.1
[ 1.562923] hub 3-0:1.0: USB hub found
[ 1.562932] hub 3-0:1.0: 3 ports detected
[ 1.563039] ohci_hcd 0000:00:0f.2: OHCI Host Controller
[ 1.563049] ohci_hcd 0000:00:0f.2: new USB bus registered, assigned bus number 4
[ 1.563075] ohci_hcd 0000:00:0f.2: irq 22, io mem 0xfa103000
[ 1.618025] usb usb4: New USB device found, idVendor=1d6b, idProduct=0001
[ 1.618030] usb usb4: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[ 1.618033] usb usb4: Product: OHCI Host Controller
[ 1.618036] usb usb4: Manufacturer: Linux 3.2.0-4-486 ohci_hcd
[ 1.618038] usb usb4: SerialNumber: 0000:00:0f.2
[ 1.618943] hub 4-0:1.0: USB hub found
[ 1.618952] hub 4-0:1.0: 3 ports detected
[ 1.668432] ata1.00: HPA detected: current 240119615, native 240121728
[ 1.668439] ata1.00: ATA-7: Maxtor 6Y120L0, YAR41KW0, max UDMA/133
[ 1.668443] ata1.00: 240119615 sectors, multi 16: LBA
[ 1.684294] ata1.00: configured for UDMA/133
[ 1.684423] scsi 0:0:0:0: Direct-Access ATA Maxtor 6Y120L0 YAR4 PQ: 0 ANSI: 5
[ 1.756016] usb 1-1: new high-speed USB device number 2 using ehci_hcd
[ 1.760012] Refined TSC clocksource calibration: 2009.934 MHz.
[ 1.760018] Switching to clocksource tsc
[ 1.848238] ata2.00: ATAPI: LITE-ON DVDRW SOHW-1693S, KS05, max UDMA/66
[ 1.848242] ata2.00: WARNING: ATAPI DMA disabled for reliability issues. It can be enabled
[ 1.848245] ata2.00: WARNING: via pata_ali.atapi_dma modparam or corresponding sysfs node.
[ 1.864129] ata2.00: configured for UDMA/66
[ 1.865311] scsi 1:0:0:0: CD-ROM LITE-ON DVDRW SOHW-1693S KS05 PQ: 0 ANSI: 5
[ 1.893346] usb 1-1: New USB device found, idVendor=0951, idProduct=1607
[ 1.893349] usb 1-1: New USB device strings: Mfr=1, Product=2, SerialNumber=3
[ 1.893352] usb 1-1: Product: DataTraveler 2.0
[ 1.893354] usb 1-1: Manufacturer: Kingston
[ 1.893356] usb 1-1: SerialNumber: 001D0F0C73C3EA41A55400D5
[ 1.897124] Initializing USB Mass Storage driver...
[ 1.897240] scsi4 : usb-storage 1-1:1.0
[ 1.897328] usbcore: registered new interface driver usb-storage
[ 1.897331] USB Mass Storage support registered.
[ 2.004011] usb 1-5: new high-speed USB device number 3 using ehci_hcd
[ 2.136727] usb 1-5: New USB device found, idVendor=079b, idProduct=0062
[ 2.136731] usb 1-5: New USB device strings: Mfr=16, Product=32, SerialNumber=0
[ 2.136734] usb 1-5: Product: 802.11b/g USB WLAN
[ 2.136736] usb 1-5: Manufacturer: ZyDAS
[ 2.189527] sd 0:0:0:0: [sda] 240119615 512-byte logical blocks: (122 GB/114 GiB)
[ 2.189578] sd 0:0:0:0: [sda] Write Protect is off
[ 2.189582] sd 0:0:0:0: [sda] Mode Sense: 00 3a 00 00
[ 2.189604] sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
[ 2.192474] sr0: scsi3-mmc drive: 48x/48x writer cd/rw xa/form2 cdda tray
[ 2.192479] cdrom: Uniform CD-ROM driver Revision: 3.20
[ 2.192811] sr 1:0:0:0: Attached scsi CD-ROM sr0
[ 2.223183] sda: sda1 sda2 < sda5 >
[ 2.223583] sd 0:0:0:0: [sda] Attached SCSI disk
[ 2.229051] sd 0:0:0:0: Attached scsi generic sg0 type 0
[ 2.229478] sr 1:0:0:0: Attached scsi generic sg1 type 5
[ 2.496017] usb 4-1: new low-speed USB device number 2 using ohci_hcd
[ 2.645116] microcode: CPU0: family 15 not supported
[ 2.645472] microcode: Microcode Update Driver: v2.00 <tigran@aivazian.fsnet.co.uk>, Peter Oruba
[ 2.707066] usb 4-1: New USB device found, idVendor=1bcf, idProduct=0007
[ 2.707071] usb 4-1: New USB device strings: Mfr=0, Product=2, SerialNumber=0
[ 2.707075] usb 4-1: Product: USB Optical Mouse
[ 2.724525] input: USB Optical Mouse as /devices/pci0000:00/0000:00:0f.2/usb4/4-1/4-1:1.0/input/input1
[ 2.724993] generic-usb 0003:1BCF:0007.0001: input,hiddev0,hidraw0: USB HID v1.10 Mouse [USB Optical Mouse] on usb-0000:00:0f.2-1/input0
[ 2.725017] usbcore: registered new interface driver usbhid
[ 2.725020] usbhid: USB HID core driver
[ 2.897851] scsi 4:0:0:0: Direct-Access Kingston DataTraveler 2.0 PMAP PQ: 0 ANSI: 0 CCS
[ 2.899037] sd 4:0:0:0: Attached scsi generic sg2 type 0
[ 2.899914] sd 4:0:0:0: [sdb] 7835648 512-byte logical blocks: (4.01 GB/3.73 GiB)
[ 2.902412] sd 4:0:0:0: [sdb] Write Protect is off
[ 2.902418] sd 4:0:0:0: [sdb] Mode Sense: 03 41 00 00
[ 2.904915] sd 4:0:0:0: [sdb] No Caching mode page present
[ 2.904973] sd 4:0:0:0: [sdb] Assuming drive cache: write through
[ 2.912762] sd 4:0:0:0: [sdb] No Caching mode page present
[ 2.912819] sd 4:0:0:0: [sdb] Assuming drive cache: write through
[ 2.914159] sdb: sdb1
[ 2.922017] sd 4:0:0:0: [sdb] No Caching mode page present
[ 2.922076] sd 4:0:0:0: [sdb] Assuming drive cache: write through
[ 2.922129] sd 4:0:0:0: [sdb] Attached SCSI removable disk
[ 3.086822] EXT4-fs (sda1): mounted filesystem with ordered data mode. Opts: (null)
[ 4.525340] FAT-fs (sdb1): utf8 is not a recommended IO charset for FAT filesystems, filesystem will be case sensitive!
[ 4.542147] aufs: module is from the staging directory, the quality is unknown, you have been warned.
[ 4.545724] aufs 3.2-20130204
[ 4.562470] loop: module loaded
[ 5.310737] squashfs: version 4.0 (2009/01/31) Phillip Lougher
[ 12.862575] udevd[879]: starting version 175
[ 13.108554] input: Power Button as /devices/LNXSYSTM:00/LNXSYBUS:00/PNP0C0C:00/input/input2
[ 13.108564] ACPI: Power Button [PWRB]
[ 13.108656] input: Power Button as /devices/LNXSYSTM:00/LNXPWRBN:00/input/input3
[ 13.108659] ACPI: Power Button [PWRF]
[ 13.188752] shpchp: Standard Hot Plug PCI Controller Driver version: 0.4
[ 13.229142] ali1563_smbus 0000:00:03.0: Found ALi1563 SMBus at 0x1400
[ 13.338117] ali1535_smbus 0000:00:03.1: ALI1535_smb region uninitialized - upgrade BIOS?
[ 13.338123] ali1535_smbus 0000:00:03.1: ALI1535 not detected, module not inserted.
[ 13.386985] ali15x3_smbus 0000:00:03.1: ALI15X3_smb region uninitialized - upgrade BIOS or use force_addr=0xaddr
[ 13.387071] ali15x3_smbus 0000:00:03.1: ALI15X3 not detected, module not inserted.
[ 13.396499] input: PC Speaker as /devices/platform/pcspkr/input/input4
[ 13.437191] alim7101_wdt: Steve Hill <steve@navaho.co.uk>.
[ 13.437206] alim7101_wdt: ALi 1543 South-Bridge not present - WDT not set
[ 13.508086] parport_pc 00:0a: reported by Plug and Play ACPI
[ 13.508113] parport0: PC-style at 0x378, irq 7 [PCSPP,EPP]
[ 13.723352] [drm] Initialized drm 1.1.0 20060810
[ 13.736363] powernow-k8: Found 1 AMD Athlon(tm) 64 Processor 3000+ (1 cpu cores) (version 2.20.00)
[ 13.736446] powernow-k8: fid 0xc (2000 MHz), vid 0x2
[ 13.736449] powernow-k8: fid 0xa (1800 MHz), vid 0x6
[ 13.736452] powernow-k8: fid 0x2 (1000 MHz), vid 0x12
[ 13.746012] gameport gameport0: NS558 PnP Gameport is pnp00:0c/gameport0, io 0x201, speed 917kHz
[ 14.032041] intel8x0_measure_ac97_clock: measured 54736 usecs (2640 samples)
[ 14.032046] intel8x0: clocking to 48000
[ 14.348155] [drm] radeon kernel modesetting enabled.
[ 14.348601] [drm] initializing kernel modesetting (RV350 0x1002:0x4153 0x1458:0x4050).
[ 14.348630] [drm] register mmio base: 0xF9000000
[ 14.348632] [drm] register mmio size: 65536
[ 14.350499] agpgart-amd64 0000:00:00.0: AGP 3.0 bridge
[ 14.350520] agpgart-amd64 0000:00:00.0: putting AGP V3 device into 8x mode
[ 14.350548] radeon 0000:01:00.0: putting AGP V3 device into 8x mode
[ 14.350559] radeon 0000:01:00.0: GTT: 128M 0xE0000000 - 0xE7FFFFFF
[ 14.350563] [drm] Generation 2 PCI interface, using max accessible memory
[ 14.350569] radeon 0000:01:00.0: VRAM: 128M 0x00000000E8000000 - 0x00000000EFFFFFFF (128M used)
[ 14.350578] [drm] Supports vblank timestamp caching Rev 1 (10.10.2010).
[ 14.350581] [drm] Driver supports precise vblank timestamp query.
[ 14.350601] [drm] radeon: irq initialized.
[ 14.350824] [drm] Detected VRAM RAM=128M, BAR=128M
[ 14.350829] [drm] RAM width 128bits DDR
[ 14.360950] [TTM] Zone kernel: Available graphics memory: 257400 kiB
[ 14.360954] [TTM] Initializing pool allocator
[ 14.360989] [drm] radeon: 128M of VRAM memory ready
[ 14.360992] [drm] radeon: 128M of GTT memory ready.
[ 14.361013] [drm] radeon: ib pool ready.
[ 14.361088] [drm] radeon: 1 quad pipes, 1 Z pipes initialized.
[ 14.362073] radeon 0000:01:00.0: WB disabled
[ 14.362082] [drm] fence driver on ring 0 use gpu addr 0xe0000000 and cpu addr 0xe0808000
[ 14.362753] [drm] Loading R300 Microcode
[ 14.390068] cfg80211: Calling CRDA to update world regulatory domain
[ 14.417066] platform radeon_cp.0: firmware: agent loaded radeon/R300_cp.bin into memory
[ 14.417446] [drm] radeon: ring at 0x00000000E0001000
[ 14.417466] [drm] ring test succeeded in 1 usecs
[ 14.417679] [drm] ib test succeeded in 0 usecs
[ 14.417929] [drm] Radeon Display Connectors
[ 14.417931] [drm] Connector 0:
[ 14.417933] [drm] VGA
[ 14.417936] [drm] DDC: 0x60 0x60 0x60 0x60 0x60 0x60 0x60 0x60
[ 14.417938] [drm] Encoders:
[ 14.417939] [drm] CRT1: INTERNAL_DAC1
[ 14.417942] [drm] Connector 1:
[ 14.417943] [drm] DVI-I
[ 14.417945] [drm] HPD1
[ 14.417947] [drm] DDC: 0x64 0x64 0x64 0x64 0x64 0x64 0x64 0x64
[ 14.417949] [drm] Encoders:
[ 14.417951] [drm] CRT2: INTERNAL_DAC2
[ 14.417953] [drm] DFP1: INTERNAL_TMDS1
[ 14.417954] [drm] Connector 2:
[ 14.417956] [drm] S-video
[ 14.417957] [drm] Encoders:
[ 14.417959] [drm] TV1: INTERNAL_DAC2
[ 14.573457] [drm] fb mappable at 0xE8040000
[ 14.573461] [drm] vram apper at 0xE8000000
[ 14.573463] [drm] size 5242880
[ 14.573465] [drm] fb depth is 24
[ 14.573467] [drm] pitch is 5120
[ 14.573910] fbcon: radeondrmfb (fb0) is primary device
[ 14.664284] Console: switching to colour frame buffer device 160x64
[ 14.698852] fb0: radeondrmfb frame buffer device
[ 14.698854] drm: registered panic notifier
[ 14.705441] [drm] Initialized radeon 2.16.0 20080528 for 0000:01:00.0 on minor 0
[ 14.844059] usb 1-5: reset high-speed USB device number 3 using ehci_hcd
[ 15.034689] ieee80211 phy0: Selected rate control algorithm 'minstrel_ht'
[ 15.035265] zd1211rw 1-5:1.0: phy0
[ 15.035298] usbcore: registered new interface driver zd1211rw
[ 15.038185] cfg80211: World regulatory domain updated:
[ 15.038190] cfg80211: (start_freq - end_freq @ bandwidth), (max_antenna_gain, max_eirp)
[ 15.038194] cfg80211: (2402000 KHz - 2472000 KHz @ 40000 KHz), (300 mBi, 2000 mBm)
[ 15.038197] cfg80211: (2457000 KHz - 2482000 KHz @ 20000 KHz), (300 mBi, 2000 mBm)
[ 15.038201] cfg80211: (2474000 KHz - 2494000 KHz @ 20000 KHz), (300 mBi, 2000 mBm)
[ 15.038204] cfg80211: (5170000 KHz - 5250000 KHz @ 40000 KHz), (300 mBi, 2000 mBm)
[ 15.038207] cfg80211: (5735000 KHz - 5835000 KHz @ 40000 KHz), (300 mBi, 2000 mBm)
[ 18.889223] Bluetooth: Core ver 2.16
[ 18.889268] NET: Registered protocol family 31
[ 18.889271] Bluetooth: HCI device and connection manager initialized
[ 18.889275] Bluetooth: HCI socket layer initialized
[ 18.889278] Bluetooth: L2CAP socket layer initialized
[ 18.892192] Bluetooth: SCO socket layer initialized
[ 19.025263] Bluetooth: BNEP (Ethernet Emulation) ver 1.3
[ 19.025268] Bluetooth: BNEP filters: protocol multicast
[ 20.492867] 8139too 0000:02:0a.0: eth0: link down
[ 20.493054] ADDRCONF(NETDEV_UP): eth0: link is not ready
[ 20.521408] usb 1-5: firmware: agent aborted loading zd1211/zd1211b_ub (not found?)
[ 20.521477] zd1211rw 1-5:1.0: couldn't load firmware. Error number -2
[ 24.348394] Marking TSC unstable due to cpufreq changes
[ 24.352401] Switching to clocksource acpi_pm
[ 32.234521] fuse init (API version 7.17)
[ 61.119561] EXT4-fs (sda1): mounted filesystem with ordered data mode. Opts: (null)Na pewno wszystko się dobrze zainstalowało? W logu jest coś takiego:
Pokaż wynik (być może będziesz to musiał wykonać jako root):
Kod: Zaznacz cały
[ 20.521408] usb 1-5: firmware: agent aborted loading zd1211/zd1211b_ub (not found?)
[ 20.521477] zd1211rw 1-5:1.0: couldn't load firmware. Error number -2Kod: Zaznacz cały
ls -l /lib/firmware/zd1211/