Uruchomienie madwifi na laptopie Asus - Squeeze
: 17 sierpnia 2009, 23:29
Witam, po dniu spędzonym przed laptopem postanowiłem w końcu poprosić was drodzy forumowicze o pomoc. Chodzi o problem z uruchomieniem wifi na laptopie Asus, na którym zainstalowanego mam Debiana Squeeze.
lspci:
ifconfig:
iwconfig:
polecenie m-a a-i madwifi wywala mi blad:
lspci:
Kod: Zaznacz cały
00:00.0 RAM memory: nVidia Corporation MCP67 Memory Controller (rev a2)
00:01.0 ISA bridge: nVidia Corporation MCP67 ISA Bridge (rev a2)
00:01.1 SMBus: nVidia Corporation MCP67 SMBus (rev a2)
00:01.2 RAM memory: nVidia Corporation MCP67 Memory Controller (rev a2)
00:01.3 Co-processor: nVidia Corporation MCP67 Co-processor (rev a2)
00:02.0 USB Controller: nVidia Corporation MCP67 OHCI USB 1.1 Controller (rev a2)
00:02.1 USB Controller: nVidia Corporation MCP67 EHCI USB 2.0 Controller (rev a2)
00:04.0 USB Controller: nVidia Corporation MCP67 OHCI USB 1.1 Controller (rev a2)
00:04.1 USB Controller: nVidia Corporation MCP67 EHCI USB 2.0 Controller (rev a2)
00:06.0 IDE interface: nVidia Corporation MCP67 IDE Controller (rev a1)
00:07.0 Audio device: nVidia Corporation MCP67 High Definition Audio (rev a1)
00:08.0 PCI bridge: nVidia Corporation MCP67 PCI Bridge (rev a2)
00:09.0 IDE interface: nVidia Corporation MCP67 AHCI Controller (rev a2)
00:0a.0 Ethernet controller: nVidia Corporation MCP67 Ethernet (rev a2)
00:0c.0 PCI bridge: nVidia Corporation MCP67 PCI Express Bridge (rev a2)
00:0d.0 PCI bridge: nVidia Corporation MCP67 PCI Express Bridge (rev a2)
00:12.0 VGA compatible controller: nVidia Corporation C67 [GeForce 7000M / nForce 610M] (rev a2)
00:18.0 Host bridge: Advanced Micro Devices [AMD] K8 [Athlon64/Opteron] HyperTransport Technology Configuration
00:18.1 Host bridge: Advanced Micro Devices [AMD] K8 [Athlon64/Opteron] Address Map
00:18.2 Host bridge: Advanced Micro Devices [AMD] K8 [Athlon64/Opteron] DRAM Controller
00:18.3 Host bridge: Advanced Micro Devices [AMD] K8 [Athlon64/Opteron] Miscellaneous Control
05:00.0 Ethernet controller: Atheros Communications Inc. AR5001 Wireless Network Adapter (rev 01)
Kod: Zaznacz cały
eth0 Link encap:Ethernet HWaddr 00:1d:60:bb:3c:a8
inet6 addr: fe80::21d:60ff:febb:3ca8/64 Scope:Link
UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1
RX packets:0 errors:0 dropped:0 overruns:0 frame:0
TX packets:40 errors:0 dropped:0 overruns:0 carrier:0
collisions:0 txqueuelen:1000
RX bytes:0 (0.0 B) TX bytes:6672 (6.5 KiB)
Interrupt:26 Base address:0x6000
eth0:avahi Link encap:Ethernet HWaddr 00:1d:60:bb:3c:a8
inet addr:169.254.8.71 Bcast:169.254.255.255 Mask:255.255.0.0
UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1
Interrupt:26 Base address:0x6000
lo Link encap:Local Loopback
inet addr:127.0.0.1 Mask:255.0.0.0
inet6 addr: ::1/128 Scope:Host
UP LOOPBACK RUNNING MTU:16436 Metric:1
RX packets:135 errors:0 dropped:0 overruns:0 frame:0
TX packets:135 errors:0 dropped:0 overruns:0 carrier:0
collisions:0 txqueuelen:0
RX bytes:9006 (8.7 KiB) TX bytes:9006 (8.7 KiB)iwconfig:
Kod: Zaznacz cały
lo no wireless extensions
eth0 no wireless extensions
pan0 no wireless extensions
Kod: Zaznacz cały
make[7]: *** [/usr/src/modules/madwifi/ath/if_ath.o] Error 1
make[6]: *** [/usr/src/modules/madwifi/ath] Error 2
make[5]: *** [_module_/usr/src/modules/madwifi] Error 2
make[4]: *** [sub-make] Error 2
make[3]: *** [all] Error 2
make[3]: Leaving directory `/usr/src/linux-headers-2.6.30-1-686'
make[2]: *** [modules] Błąd 2
make[2]: Opuszczenie katalogu `/usr/src/modules/madwifi'
make[1]: *** [binary-modules] Błąd 2
make[1]: Opuszczenie katalogu `/usr/src/modules/madwifi'
make: *** [kdist_build] Błąd 2