Uruchomienie madwifi na laptopie Asus - Squeeze

[b4rteq]

Witam, po dniu spędzonym przed laptopem postanowiłem w końcu poprosić was drodzy forumowicze o pomoc. Chodzi o problem z uruchomieniem wifi na laptopie Asus, na którym zainstalowanego mam Debiana Squeeze.


lspci:

Kod: Zaznacz cały

00:00.0 RAM memory: nVidia Corporation MCP67 Memory Controller (rev a2)
00:01.0 ISA bridge: nVidia Corporation MCP67 ISA Bridge (rev a2)
00:01.1 SMBus: nVidia Corporation MCP67 SMBus (rev a2)
00:01.2 RAM memory: nVidia Corporation MCP67 Memory Controller (rev a2)
00:01.3 Co-processor: nVidia Corporation MCP67 Co-processor (rev a2)
00:02.0 USB Controller: nVidia Corporation MCP67 OHCI USB 1.1 Controller (rev a2)
00:02.1 USB Controller: nVidia Corporation MCP67 EHCI USB 2.0 Controller (rev a2)
00:04.0 USB Controller: nVidia Corporation MCP67 OHCI USB 1.1 Controller (rev a2)
00:04.1 USB Controller: nVidia Corporation MCP67 EHCI USB 2.0 Controller (rev a2)
00:06.0 IDE interface: nVidia Corporation MCP67 IDE Controller (rev a1)
00:07.0 Audio device: nVidia Corporation MCP67 High Definition Audio (rev a1)
00:08.0 PCI bridge: nVidia Corporation MCP67 PCI Bridge (rev a2)
00:09.0 IDE interface: nVidia Corporation MCP67 AHCI Controller (rev a2)
00:0a.0 Ethernet controller: nVidia Corporation MCP67 Ethernet (rev a2)
00:0c.0 PCI bridge: nVidia Corporation MCP67 PCI Express Bridge (rev a2)
00:0d.0 PCI bridge: nVidia Corporation MCP67 PCI Express Bridge (rev a2)
00:12.0 VGA compatible controller: nVidia Corporation C67 [GeForce 7000M / nForce 610M] (rev a2)
00:18.0 Host bridge: Advanced Micro Devices [AMD] K8 [Athlon64/Opteron] HyperTransport Technology Configuration
00:18.1 Host bridge: Advanced Micro Devices [AMD] K8 [Athlon64/Opteron] Address Map
00:18.2 Host bridge: Advanced Micro Devices [AMD] K8 [Athlon64/Opteron] DRAM Controller
00:18.3 Host bridge: Advanced Micro Devices [AMD] K8 [Athlon64/Opteron] Miscellaneous Control
05:00.0 Ethernet controller: Atheros Communications Inc. AR5001 Wireless Network Adapter (rev 01)

ifconfig:

Kod: Zaznacz cały

eth0      Link encap:Ethernet  HWaddr 00:1d:60:bb:3c:a8  
          inet6 addr: fe80::21d:60ff:febb:3ca8/64 Scope:Link
          UP BROADCAST RUNNING MULTICAST  MTU:1500  Metric:1
          RX packets:0 errors:0 dropped:0 overruns:0 frame:0
          TX packets:40 errors:0 dropped:0 overruns:0 carrier:0
          collisions:0 txqueuelen:1000 
          RX bytes:0 (0.0 B)  TX bytes:6672 (6.5 KiB)
          Interrupt:26 Base address:0x6000 

eth0:avahi Link encap:Ethernet  HWaddr 00:1d:60:bb:3c:a8  
          inet addr:169.254.8.71  Bcast:169.254.255.255  Mask:255.255.0.0
          UP BROADCAST RUNNING MULTICAST  MTU:1500  Metric:1
          Interrupt:26 Base address:0x6000 

lo        Link encap:Local Loopback  
          inet addr:127.0.0.1  Mask:255.0.0.0
          inet6 addr: ::1/128 Scope:Host
          UP LOOPBACK RUNNING  MTU:16436  Metric:1
          RX packets:135 errors:0 dropped:0 overruns:0 frame:0
          TX packets:135 errors:0 dropped:0 overruns:0 carrier:0
          collisions:0 txqueuelen:0 
          RX bytes:9006 (8.7 KiB)  TX bytes:9006 (8.7 KiB)

iwconfig:

Kod: Zaznacz cały

lo       no wireless extensions
eth0   no wireless extensions
pan0  no wireless extensions

polecenie m-a a-i madwifi wywala mi blad:

Kod: Zaznacz cały

make[7]: *** [/usr/src/modules/madwifi/ath/if_ath.o] Error 1
make[6]: *** [/usr/src/modules/madwifi/ath] Error 2
make[5]: *** [_module_/usr/src/modules/madwifi] Error 2
make[4]: *** [sub-make] Error 2
make[3]: *** [all] Error 2
make[3]: Leaving directory `/usr/src/linux-headers-2.6.30-1-686'
make[2]: *** [modules] Błąd 2
make[2]: Opuszczenie katalogu `/usr/src/modules/madwifi'
make[1]: *** [binary-modules] Błąd 2
make[1]: Opuszczenie katalogu `/usr/src/modules/madwifi'
make: *** [kdist_build] Błąd 2

[ryba84]

Masz jądro 2.6.30, więc karta AR5001 jest obsługiwana przez moduł ath9k. Nie musisz kompilować madwifi. Poza tym nie bawił bym się w madwifi, które chyba nie kompiluje się z nowymi jądrami, tylko jeśli już to w madwifi-ng bo to jego następca.