Witam!
Posiadam kilkanaście urządzeń USB, które zajmują porty od ttyUSB0 do ttyUSB15. Niemniej jednak mam też modem 3G, który chciałbym by zawsze był wykrywany na tym samym porcie – np. na ttyUSB20.
Czy można tego dokonać? Oczywiście modem będzie zawsze podpięty do tego samego gnieźda USB. Niemniej jednak urządzenia od ttyUSB0 do 15, uruchamiają się losowo, i chcę by ten modem 3G zawsze był pod tym samym portem (nie może być z przedziału 0 do 15, bo z tymi urządzeniami się komunikuje pewną aplikacją).
Jakaś podpowiedź?
Pozdrawiam.
Przypisanie konkretnego urz
To powinno pomóc: http://hintshop.ludvig.co.nz/show/persi ... l-devices/
Pokaż wyniki:
po podłączeniu modemu.
Kod: Zaznacz cały
lsusb
dmesglsusb:
dmesg:
Kod: Zaznacz cały
root@debian:~# lsusb
Bus 001 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub
Bus 002 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub
Bus 003 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub
Bus 001 Device 002: ID 0403:6011 Future Technology Devices International, Ltd FT4232H Quad HS USB-UART/FIFO IC
Bus 001 Device 003: ID 13fe:3800 Kingston Technology Company Inc. Rage XT Flash DriveKod: Zaznacz cały
[ 0.000000] Initializing cgroup subsys cpuset
[ 0.000000] Initializing cgroup subsys cpu
[ 0.000000] Linux version 3.2.0-4-686-pae (debian-kernel@lists.debian.org) (gcc version 4.6.3 (Debian 4.6.3-14) ) #1 SMP Debian 3.2.41-2+deb7u2
[ 0.000000] BIOS-provided physical RAM map:
[ 0.000000] BIOS-e820: 0000000000000000 - 000000000009fc00 (usable)
[ 0.000000] BIOS-e820: 000000000009fc00 - 00000000000a0000 (reserved)
[ 0.000000] BIOS-e820: 00000000000f0000 - 0000000000100000 (reserved)
[ 0.000000] BIOS-e820: 0000000000100000 - 000000003e7f0000 (usable)
[ 0.000000] BIOS-e820: 000000003e7f0000 - 000000003e7f3000 (ACPI NVS)
[ 0.000000] BIOS-e820: 000000003e7f3000 - 000000003e800000 (ACPI data)
[ 0.000000] BIOS-e820: 00000000ffff0000 - 0000000100000000 (reserved)
[ 0.000000] NX (Execute Disable) protection: active
[ 0.000000] SMBIOS 2.3 present.
[ 0.000000] DMI: Hewlett-Packard hp t5000 series/098Ch, BIOS 786R2 v1.02 12/20/2004
[ 0.000000] e820 update range: 0000000000000000 - 0000000000010000 (usable) ==> (reserved)
[ 0.000000] e820 remove range: 00000000000a0000 - 0000000000100000 (usable)
[ 0.000000] last_pfn = 0x3e7f0 max_arch_pfn = 0x1000000
[ 0.000000] MTRR default type: uncachable
[ 0.000000] MTRR fixed ranges enabled:
[ 0.000000] 00000-9FFFF write-back
[ 0.000000] A0000-BFFFF uncachable
[ 0.000000] C0000-C8FFF write-back
[ 0.000000] C9000-FFFFF uncachable
[ 0.000000] MTRR variable ranges enabled:
[ 0.000000] 0 base 000000000 mask FC0000000 write-back
[ 0.000000] 1 base 03E800000 mask FFF800000 uncachable
[ 0.000000] 2 base 03F000000 mask FFF000000 uncachable
[ 0.000000] 3 disabled
[ 0.000000] 4 disabled
[ 0.000000] 5 disabled
[ 0.000000] 6 disabled
[ 0.000000] 7 disabled
[ 0.000000] x86 PAT enabled: cpu 0, old 0x7040600070406, new 0x7010600070106
[ 0.000000] initial memory mapped : 0 - 01a00000
[ 0.000000] Base memory trampoline at [c009b000] 9b000 size 16384
[ 0.000000] init_memory_mapping: 0000000000000000-00000000379fe000
[ 0.000000] 0000000000 - 0000200000 page 4k
[ 0.000000] 0000200000 - 0037800000 page 2M
[ 0.000000] 0037800000 - 00379fe000 page 4k
[ 0.000000] kernel direct mapping tables up to 379fe000 @ 19f9000-1a00000
[ 0.000000] RAMDISK: 36d1c000 - 37686000
[ 0.000000] ACPI: RSDP 000f64a0 00014 (v00 TM8000)
[ 0.000000] ACPI: RSDT 3e7f3000 00028 (v01 TM8000 AWRDACPI 42302E31 AWRD 00000000)
[ 0.000000] ACPI: FACP 3e7f3040 00074 (v01 TM8000 AWRDACPI 42302E31 AWRD 00000000)
[ 0.000000] ACPI: DSDT 3e7f30c0 03A5C (v01 TM8000 AWRDACPI 00001003 MSFT 0100000E)
[ 0.000000] ACPI: FACS 3e7f0000 00040
[ 0.000000] 109MB HIGHMEM available.
[ 0.000000] 889MB LOWMEM available.
[ 0.000000] mapped low ram: 0 - 379fe000
[ 0.000000] low ram: 0 - 379fe000
[ 0.000000] Zone PFN ranges:
[ 0.000000] DMA 0x00000010 -> 0x00001000
[ 0.000000] Normal 0x00001000 -> 0x000379fe
[ 0.000000] HighMem 0x000379fe -> 0x0003e7f0
[ 0.000000] Movable zone start PFN for each node
[ 0.000000] early_node_map[2] active PFN ranges
[ 0.000000] 0: 0x00000010 -> 0x0000009f
[ 0.000000] 0: 0x00000100 -> 0x0003e7f0
[ 0.000000] On node 0 totalpages: 255871
[ 0.000000] free_area_init_node: node 0, pgdat c1412600, node_mem_map f654c200
[ 0.000000] DMA zone: 32 pages used for memmap
[ 0.000000] DMA zone: 0 pages reserved
[ 0.000000] DMA zone: 3951 pages, LIFO batch:0
[ 0.000000] Normal zone: 1748 pages used for memmap
[ 0.000000] Normal zone: 221994 pages, LIFO batch:31
[ 0.000000] HighMem zone: 220 pages used for memmap
[ 0.000000] HighMem zone: 27926 pages, LIFO batch:7
[ 0.000000] Using APIC driver default
[ 0.000000] ACPI: PM-Timer IO Port: 0x4008
[ 0.000000] SMP: Allowing 1 CPUs, 0 hotplug CPUs
[ 0.000000] No local APIC present or hardware disabled
[ 0.000000] APIC: disable apic facility
[ 0.000000] APIC: switched to apic NOOP
[ 0.000000] nr_irqs_gsi: 16
[ 0.000000] PM: Registered nosave memory: 000000000009f000 - 00000000000a0000
[ 0.000000] PM: Registered nosave memory: 00000000000a0000 - 00000000000f0000
[ 0.000000] PM: Registered nosave memory: 00000000000f0000 - 0000000000100000
[ 0.000000] Allocating PCI resources starting at 3e800000 (gap: 3e800000:c17f0000)
[ 0.000000] Booting paravirtualized kernel on bare hardware
[ 0.000000] setup_percpu: NR_CPUS:32 nr_cpumask_bits:32 nr_cpu_ids:1 nr_node_ids:1
[ 0.000000] PERCPU: Embedded 14 pages/cpu @f79e9000 s33280 r0 d24064 u57344
[ 0.000000] pcpu-alloc: s33280 r0 d24064 u57344 alloc=14*4096
[ 0.000000] pcpu-alloc: [0] 0
[ 0.000000] Built 1 zonelists in Zone order, mobility grouping on. Total pages: 253871
[ 0.000000] Kernel command line: BOOT_IMAGE=/boot/vmlinuz-3.2.0-4-686-pae root=UUID=85d1f3c8-1197-4228-9cab-fc963e70cae2 ro quiet
[ 0.000000] PID hash table entries: 4096 (order: 2, 16384 bytes)
[ 0.000000] Dentry cache hash table entries: 131072 (order: 7, 524288 bytes)
[ 0.000000] Inode-cache hash table entries: 65536 (order: 6, 262144 bytes)
[ 0.000000] Initializing CPU#0
[ 0.000000] Initializing HighMem for node 0 (000379fe:0003e7f0)
[ 0.000000] Memory: 999736k/1023936k available (2847k kernel code, 23748k reserved, 1352k data, 416k init, 112584k highmem)
[ 0.000000] virtual kernel memory layout:
[ 0.000000] fixmap : 0xffd36000 - 0xfffff000 (2852 kB)
[ 0.000000] pkmap : 0xffa00000 - 0xffc00000 (2048 kB)
[ 0.000000] vmalloc : 0xf81fe000 - 0xff9fe000 ( 120 MB)
[ 0.000000] lowmem : 0xc0000000 - 0xf79fe000 ( 889 MB)
[ 0.000000] .init : 0xc141a000 - 0xc1482000 ( 416 kB)
[ 0.000000] .data : 0xc12c7e80 - 0xc1419f40 (1352 kB)
[ 0.000000] .text : 0xc1000000 - 0xc12c7e80 (2847 kB)
[ 0.000000] Checking if this processor honours the WP bit even in supervisor mode...Ok.
[ 0.000000] Hierarchical RCU implementation.
[ 0.000000] RCU dyntick-idle grace-period acceleration is enabled.
[ 0.000000] NR_IRQS:2304 nr_irqs:256 16
[ 0.000000] CPU 0 irqstacks, hard=f6008000 soft=f600a000
[ 0.000000] spurious 8259A interrupt: IRQ7.
[ 0.000000] Console: colour VGA+ 80x25
[ 0.000000] console [tty0] enabled
[ 0.000000] Fast TSC calibration failed
[ 0.000000] TSC: PIT calibration matches PMTIMER. 2 loops
[ 0.000000] Detected 1197.190 MHz processor.
[ 0.012024] Calibrating delay loop (skipped), value calculated using timer frequency.. 2394.38 BogoMIPS (lpj=4788760)
[ 0.012057] pid_max: default: 32768 minimum: 301
[ 0.013199] Security Framework initialized
[ 0.013249] AppArmor: AppArmor disabled by boot time parameter
[ 0.013623] Mount-cache hash table entries: 512
[ 0.020737] Initializing cgroup subsys cpuacct
[ 0.021003] Initializing cgroup subsys memory
[ 0.021069] Initializing cgroup subsys devices
[ 0.021089] Initializing cgroup subsys freezer
[ 0.021106] Initializing cgroup subsys net_cls
[ 0.021123] Initializing cgroup subsys blkio
[ 0.021312] Initializing cgroup subsys perf_event
[ 0.022899] CPU: Processor revision 43449201, 1200 MHz
[ 0.022922] CPU: Code Morphing Software revision 6.0.4-1-62
[ 0.022940] CPU: 20040723 20:41 official release 6.0.4#6
[ 0.022962] CPU serial number disabled.
[ 0.023025] mce: CPU supports 4 MCE banks
[ 0.024228] SMP alternatives: switching to UP code
[ 0.035191] Freeing SMP alternatives: 8k freed
[ 0.035408] ACPI: Core revision 20110623
[ 0.066710] ACPI: setting ELCR to 0200 (from 0c28)
[ 0.070977] weird, boot CPU (#0) not listed by the BIOS.
[ 0.071000] SMP motherboard not detected.
[ 0.071059] Local APIC not detected. Using dummy APIC emulation.
[ 0.071072] SMP disabled
[ 0.071094] Performance Events:
[ 0.077265] NMI watchdog disabled (cpu0): hardware events not enabled
[ 0.079754] Brought up 1 CPUs
[ 0.080068] Total of 1 processors activated (2394.38 BogoMIPS).
[ 0.089887] devtmpfs: initialized
[ 0.097450] PM: Registering ACPI NVS region at 3e7f0000 (12288 bytes)
[ 0.107172] print_constraints: dummy:
[ 0.109717] NET: Registered protocol family 16
[ 0.113635] ACPI: bus type pci registered
[ 0.137905] PCI : PCI BIOS aera is rw and x. Use pci=nobios if you want it NX.
[ 0.137972] PCI: PCI BIOS revision 2.10 entry at 0xfa560, last bus=2
[ 0.137985] PCI: Using configuration type 1 for base access
[ 0.150191] bio: create slab <bio-0> at 0
[ 0.151693] ACPI: Added _OSI(Module Device)
[ 0.151771] ACPI: Added _OSI(Processor Device)
[ 0.151788] ACPI: Added _OSI(3.0 _SCP Extensions)
[ 0.151805] ACPI: Added _OSI(Processor Aggregator Device)
[ 0.155034] ACPI: EC: Look up EC in DSDT
[ 0.190107] ACPI: Interpreter enabled
[ 0.190142] ACPI: (supports S0 S5)
[ 0.190429] ACPI: Using PIC for interrupt routing
[ 0.225195] ACPI: No dock devices found.
[ 0.225219] HEST: Table not found.
[ 0.225461] PCI: Ignoring host bridge windows from ACPI; if necessary, use "pci=use_crs" and report a bug
[ 0.226717] ACPI: PCI Root Bridge [PCI0] (domain 0000 [bus 00-ff])
[ 0.230207] pci_root PNP0A03:00: host bridge window [io 0x0000-0x0cf7] (ignored)
[ 0.230309] pci_root PNP0A03:00: host bridge window [io 0x0d00-0xffff] (ignored)
[ 0.230353] pci_root PNP0A03:00: host bridge window [mem 0x000a0000-0x000bffff] (ignored)
[ 0.230390] pci_root PNP0A03:00: host bridge window [mem 0x000c0000-0x000dffff] (ignored)
[ 0.230432] pci_root PNP0A03:00: host bridge window [mem 0x3e800000-0xffefffff] (ignored)
[ 0.230897] pci 0000:00:00.0: [1279:0060] type 0 class 0x000600
[ 0.231743] pci 0000:00:00.0: reg 10: [mem 0xe8000000-0xebffffff pref]
[ 0.232612] pci 0000:00:01.0: [1279:0061] type 1 class 0x000604
[ 0.233379] pci 0000:00:02.0: [10b9:5249] type 1 class 0x000604
[ 0.234388] pci 0000:00:03.0: [10b9:1563] type 0 class 0x000601
[ 0.234827] pci 0000:00:03.1: [10b9:7101] type 0 class 0x000680
[ 0.235502] pci 0000:00:03.1: quirk: [io 0x4000-0x403f] claimed by ali7101 ACPI
[ 0.235733] pci 0000:00:04.0: [10b9:5455] type 0 class 0x000401
[ 0.235798] pci 0000:00:04.0: reg 10: [io 0xe000-0xe0ff]
[ 0.236014] pci 0000:00:04.0: reg 14: [mem 0xec200000-0xec200fff]
[ 0.236338] pci 0000:00:04.0: supports D1 D2
[ 0.236352] pci 0000:00:04.0: PME# supported from D2 D3hot D3cold
[ 0.236952] pci 0000:00:0e.0: [10b9:5229] type 0 class 0x000101
[ 0.237384] pci 0000:00:0e.0: reg 20: [io 0xf000-0xf00f]
[ 0.237709] pci 0000:00:0f.0: [10b9:5237] type 0 class 0x000c03
[ 0.237765] pci 0000:00:0f.0: reg 10: [mem 0xec201000-0xec201fff]
[ 0.237946] pci 0000:00:0f.0: supports D1 D2
[ 0.237957] pci 0000:00:0f.0: PME# supported from D0 D1 D2 D3hot D3cold
[ 0.238141] pci 0000:00:0f.1: [10b9:5237] type 0 class 0x000c03
[ 0.238357] pci 0000:00:0f.1: reg 10: [mem 0xec202000-0xec202fff]
[ 0.238538] pci 0000:00:0f.1: supports D1 D2
[ 0.238548] pci 0000:00:0f.1: PME# supported from D0 D1 D2 D3hot D3cold
[ 0.238646] pci 0000:00:0f.3: [10b9:5239] type 0 class 0x000c03
[ 0.238749] pci 0000:00:0f.3: reg 10: [mem 0xec204000-0xec2040ff]
[ 0.238923] pci 0000:00:0f.3: PME# supported from D0 D3hot D3cold
[ 0.239337] pci 0000:01:00.0: [1002:5159] type 0 class 0x000300
[ 0.239379] pci 0000:01:00.0: reg 10: [mem 0xe0000000-0xe7ffffff pref]
[ 0.239404] pci 0000:01:00.0: reg 14: [io 0xc000-0xc0ff]
[ 0.239428] pci 0000:01:00.0: reg 18: [mem 0xec020000-0xec02ffff]
[ 0.239471] pci 0000:01:00.0: reg 30: [mem 0x00000000-0x0001ffff pref]
[ 0.239530] pci 0000:01:00.0: supports D1 D2
[ 0.239634] pci 0000:00:01.0: PCI bridge to [bus 01-01]
[ 0.239655] pci 0000:00:01.0: bridge window [io 0xc000-0xcfff]
[ 0.239675] pci 0000:00:01.0: bridge window [mem 0xec000000-0xec0fffff]
[ 0.239732] pci 0000:00:01.0: bridge window [mem 0xe0000000-0xe7ffffff pref]
[ 0.239857] pci 0000:02:05.0: [1106:3065] type 0 class 0x000200
[ 0.239904] pci 0000:02:05.0: reg 10: [io 0xd000-0xd0ff]
[ 0.240034] pci 0000:02:05.0: reg 14: [mem 0xec100000-0xec1000ff]
[ 0.240175] pci 0000:02:05.0: supports D1 D2
[ 0.240184] pci 0000:02:05.0: PME# supported from D0 D1 D2 D3hot D3cold
[ 0.240271] pci 0000:00:02.0: PCI bridge to [bus 02-02]
[ 0.240291] pci 0000:00:02.0: bridge window [io 0xd000-0xdfff]
[ 0.240678] pci 0000:00:02.0: bridge window [mem 0xec100000-0xec1fffff]
[ 0.240732] pci_bus 0000:00: on NUMA node 0
[ 0.240756] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0._PRT]
[ 0.241925] ACPI: firmware reports 0000:00:01 PCI INT A connected to \_SB_.PCI0.LNK1; changing to \_SB_.PCI0.LNK3
[ 0.242385] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.P2PB._PRT]
[ 0.243992] pci0000:00: Unable to request _OSC control (_OSC support mask: 0x1e)
[ 0.276130] ACPI: PCI Interrupt Link [LNK1] (IRQs 1 3 4 5 6 7 10 *11 12 14 15)
[ 0.277847] ACPI: PCI Interrupt Link [LNK2] (IRQs 1 3 4 5 6 7 10 11 12 14 15) *0, disabled.
[ 0.279279] ACPI: PCI Interrupt Link [LNK3] (IRQs 1 *3 4 5 6 7 10 11 12 14 15)
[ 0.280539] ACPI: PCI Interrupt Link [LNK4] (IRQs 1 3 4 5 6 7 10 11 12 14 15) *0, disabled.
[ 0.280927] ACPI: PCI Interrupt Link [LNK5] (IRQs 1 3 4 5 6 7 10 11 12 14 15) *0, disabled.
[ 0.281502] ACPI: PCI Interrupt Link [LNK6] (IRQs 1 3 4 5 6 7 *10 11 12 14 15)
[ 0.282065] ACPI: PCI Interrupt Link [LNK7] (IRQs 1 3 4 5 6 7 10 11 12 14 15) *0, disabled.
[ 0.282512] ACPI: PCI Interrupt Link [LNK9] (IRQs 1 3 4 *5 6 7 10 11 12 14 15)
[ 0.283924] vgaarb: device added: PCI:0000:01:00.0,decodes=io+mem,owns=io+mem,locks=none
[ 0.284271] vgaarb: loaded
[ 0.284279] vgaarb: bridge control possible 0000:01:00.0
[ 0.285246] PCI: Using ACPI for IRQ routing
[ 0.285344] PCI: pci_cache_line_size set to 128 bytes
[ 0.287021] reserve RAM buffer: 000000000009fc00 - 000000000009ffff
[ 0.287044] reserve RAM buffer: 000000003e7f0000 - 000000003fffffff
[ 0.289369] Switching to clocksource pit
[ 0.303484] pnp: PnP ACPI init
[ 0.303565] ACPI: bus type pnp registered
[ 0.304631] pnp 00:00: [mem 0x000da000-0x000dbfff]
[ 0.304733] pnp 00:00: [mem 0x000f0000-0x000f7fff]
[ 0.304754] pnp 00:00: [mem 0x000f8000-0x000fbfff]
[ 0.304840] pnp 00:00: [mem 0x000fc000-0x000fffff]
[ 0.304855] pnp 00:00: [mem 0x3e7f0000-0x3e7fffff]
[ 0.304868] pnp 00:00: [mem 0xffff0000-0xffffffff]
[ 0.304880] pnp 00:00: [mem 0x00000000-0x0009ffff]
[ 0.304892] pnp 00:00: [mem 0x00100000-0x3e7effff]
[ 0.304904] pnp 00:00: [mem 0xfee00000-0xfee00fff]
[ 0.306043] system 00:00: [mem 0x000da000-0x000dbfff] has been reserved
[ 0.306066] system 00:00: [mem 0x000f0000-0x000f7fff] could not be reserved
[ 0.306085] system 00:00: [mem 0x000f8000-0x000fbfff] could not be reserved
[ 0.306104] system 00:00: [mem 0x000fc000-0x000fffff] could not be reserved
[ 0.306181] system 00:00: [mem 0x3e7f0000-0x3e7fffff] could not be reserved
[ 0.306202] system 00:00: [mem 0xffff0000-0xffffffff] has been reserved
[ 0.306220] system 00:00: [mem 0x00000000-0x0009ffff] could not be reserved
[ 0.306264] system 00:00: [mem 0x00100000-0x3e7effff] could not be reserved
[ 0.306281] system 00:00: [mem 0xfee00000-0xfee00fff] has been reserved
[ 0.306322] system 00:00: Plug and Play ACPI device, IDs PNP0c01 (active)
[ 0.306804] pnp 00:01: [bus 00-ff]
[ 0.306823] pnp 00:01: [io 0x0cf8-0x0cff]
[ 0.306841] pnp 00:01: [io 0x0000-0x0cf7 window]
[ 0.306858] pnp 00:01: [io 0x0d00-0xffff window]
[ 0.306870] pnp 00:01: [io 0x5000-0x501f]
[ 0.306882] pnp 00:01: [io 0x4000-0x403f]
[ 0.306894] pnp 00:01: [io 0x04d6]
[ 0.306910] pnp 00:01: [mem 0x000a0000-0x000bffff window]
[ 0.306926] pnp 00:01: [mem 0x000c0000-0x000dffff window]
[ 0.307121] pnp 00:01: [mem 0x3e800000-0xffefffff window]
[ 0.307838] pnp 00:01: Plug and Play ACPI device, IDs PNP0a03 (active)
[ 0.308745] pnp 00:02: [io 0x0010-0x001f]
[ 0.308760] pnp 00:02: [io 0x0022-0x003f]
[ 0.308772] pnp 00:02: [io 0x0044-0x005f]
[ 0.308854] pnp 00:02: [io 0x0062-0x0063]
[ 0.308868] pnp 00:02: [io 0x0065-0x006f]
[ 0.308953] pnp 00:02: [io 0x0074-0x007f]
[ 0.308965] pnp 00:02: [io 0x0091-0x0093]
[ 0.308976] pnp 00:02: [io 0x00a2-0x00bf]
[ 0.308987] pnp 00:02: [io 0x00e0-0x00ef]
[ 0.308999] pnp 00:02: [io 0x04d0-0x04d1]
[ 0.309010] pnp 00:02: [io 0x0800-0x087f]
[ 0.309365] system 00:02: [io 0x04d0-0x04d1] has been reserved
[ 0.309384] system 00:02: [io 0x0800-0x087f] has been reserved
[ 0.309403] system 00:02: Plug and Play ACPI device, IDs PNP0c02 (active)
[ 0.309482] pnp 00:03: [dma 4]
[ 0.309494] pnp 00:03: [io 0x0000-0x000f]
[ 0.309506] pnp 00:03: [io 0x0080-0x0090]
[ 0.309517] pnp 00:03: [io 0x0094-0x009f]
[ 0.309529] pnp 00:03: [io 0x00c0-0x00df]
[ 0.309727] pnp 00:03: Plug and Play ACPI device, IDs PNP0200 (active)
[ 0.309967] pnp 00:04: [io 0x0070-0x0073]
[ 0.309991] pnp 00:04: [irq 8]
[ 0.310145] pnp 00:04: Plug and Play ACPI device, IDs PNP0b00 (active)
[ 0.310633] pnp 00:05: [io 0x0061]
[ 0.310874] pnp 00:05: Plug and Play ACPI device, IDs PNP0800 (active)
[ 0.311018] pnp 00:06: [io 0x00f0-0x00ff]
[ 0.311309] pnp 00:06: [irq 13]
[ 0.311490] pnp 00:06: Plug and Play ACPI device, IDs PNP0c04 (active)
[ 0.312218] pnp 00:07: [io 0x03f8-0x03ff]
[ 0.312287] pnp 00:07: [irq 4]
[ 0.313200] pnp 00:07: Plug and Play ACPI device, IDs PNP0501 (active)
[ 0.314215] pnp 00:08: [io 0x0378-0x037f]
[ 0.314280] pnp 00:08: [io 0x0778-0x077b]
[ 0.314300] pnp 00:08: [irq 7]
[ 0.314312] pnp 00:08: [dma 3]
[ 0.314883] pnp 00:08: Plug and Play ACPI device, IDs PNP0401 (active)
[ 0.315233] pnp: PnP ACPI: found 9 devices
[ 0.315245] ACPI: ACPI bus type pnp unregistered
[ 0.315259] PnPBIOS: Disabled by ACPI PNP
[ 0.372984] Switching to clocksource acpi_pm
[ 0.373123] PCI: max bus depth: 1 pci_try_num: 2
[ 0.373863] pci 0000:01:00.0: BAR 6: assigned [mem 0xec000000-0xec01ffff pref]
[ 0.373885] pci 0000:00:01.0: PCI bridge to [bus 01-01]
[ 0.373899] pci 0000:00:01.0: bridge window [io 0xc000-0xcfff]
[ 0.373993] pci 0000:00:01.0: bridge window [mem 0xec000000-0xec0fffff]
[ 0.374009] pci 0000:00:01.0: bridge window [mem 0xe0000000-0xe7ffffff pref]
[ 0.374036] pci 0000:00:02.0: PCI bridge to [bus 02-02]
[ 0.374048] pci 0000:00:02.0: bridge window [io 0xd000-0xdfff]
[ 0.374066] pci 0000:00:02.0: bridge window [mem 0xec100000-0xec1fffff]
[ 0.374219] pci 0000:00:01.0: setting latency timer to 64
[ 0.374659] pci 0000:00:02.0: setting latency timer to 64
[ 0.374681] pci_bus 0000:00: resource 0 [io 0x0000-0xffff]
[ 0.374691] pci_bus 0000:00: resource 1 [mem 0x00000000-0xffffffff]
[ 0.374703] pci_bus 0000:01: resource 0 [io 0xc000-0xcfff]
[ 0.374712] pci_bus 0000:01: resource 1 [mem 0xec000000-0xec0fffff]
[ 0.374724] pci_bus 0000:01: resource 2 [mem 0xe0000000-0xe7ffffff pref]
[ 0.374735] pci_bus 0000:02: resource 0 [io 0xd000-0xdfff]
[ 0.374745] pci_bus 0000:02: resource 1 [mem 0xec100000-0xec1fffff]
[ 0.375425] NET: Registered protocol family 2
[ 0.376940] IP route cache hash table entries: 32768 (order: 5, 131072 bytes)
[ 0.382620] TCP established hash table entries: 131072 (order: 8, 1048576 bytes)
[ 0.385003] TCP bind hash table entries: 65536 (order: 7, 524288 bytes)
[ 0.386086] TCP: Hash tables configured (established 131072 bind 65536)
[ 0.386101] TCP reno registered
[ 0.386134] UDP hash table entries: 512 (order: 2, 16384 bytes)
[ 0.386983] UDP-Lite hash table entries: 512 (order: 2, 16384 bytes)
[ 0.388583] NET: Registered protocol family 1
[ 0.389734] ACPI: PCI Interrupt Link [LNK3] enabled at IRQ 3
[ 0.389751] PCI: setting IRQ 3 as level-triggered
[ 0.515245] ACPI: PCI Interrupt Link [LNK9] enabled at IRQ 5
[ 0.515270] PCI: setting IRQ 5 as level-triggered
[ 0.515636] PCI: CLS mismatch (32 != 64), using 128 bytes
[ 0.515678] pci 0000:01:00.0: Boot video device
[ 0.519055] Unpacking initramfs...
[ 1.164605] Freeing initrd memory: 9640k freed
[ 1.184908] audit: initializing netlink socket (disabled)
[ 1.185062] type=2000 audit(1370595308.181:1): initialized
[ 1.222929] highmem bounce pool size: 64 pages
[ 1.222974] HugeTLB registered 2 MB page size, pre-allocated 0 pages
[ 1.225746] VFS: Disk quotas dquot_6.5.2
[ 1.226219] Dquot-cache hash table entries: 1024 (order 0, 4096 bytes)
[ 1.226917] msgmni has been set to 1751
[ 1.230695] alg: No test for stdrng (krng)
[ 1.230870] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 253)
[ 1.230888] io scheduler noop registered
[ 1.230897] io scheduler deadline registered
[ 1.230932] io scheduler cfq registered (default)
[ 1.231878] pci_hotplug: PCI Hot Plug PCI Core version: 0.5
[ 1.231999] pciehp: PCI Express Hot Plug Controller Driver version: 0.4
[ 1.232079] acpiphp: ACPI Hot Plug PCI Controller Driver version: 0.5
[ 1.235678] ERST: Table is not found!
[ 1.235689] GHES: HEST is not enabled!
[ 1.235745] isapnp: Scanning for PnP cards...
[ 1.591905] isapnp: No Plug & Play device found
[ 1.592272] Serial: 8250/16550 driver, 4 ports, IRQ sharing enabled
[ 1.613647] serial8250: ttyS0 at I/O 0x3f8 (irq = 4) is a 16550A
[ 1.636490] 00:07: ttyS0 at I/O 0x3f8 (irq = 4) is a 16550A
[ 1.637192] Linux agpgart interface v0.103
[ 1.637636] agpgart: Detected Transmeta Efficeon TM8000 series chipset
[ 1.637672] agpgart-efficeon 0000:00:00.0: enabling device (0100 -> 0102)
[ 1.637711] agpgart: efficeon_create_gatt_table(16384)
[ 1.638395] agpgart: efficeon_configure()
[ 1.638586] agpgart-efficeon 0000:00:00.0: AGP aperture is 64M @ 0xe8000000
[ 1.639783] i8042: PNP: No PS/2 controller found. Probing ports directly.
[ 1.892589] serio: i8042 KBD port at 0x60,0x64 irq 1
[ 1.893450] mousedev: PS/2 mouse device common for all mice
[ 1.893892] rtc_cmos 00:04: RTC can wake from S4
[ 1.894639] rtc_cmos 00:04: rtc core: registered rtc_cmos as rtc0
[ 1.895048] rtc0: alarms up to one month, 242 bytes nvram
[ 1.895137] cpuidle: using governor ladder
[ 1.895160] cpuidle: using governor menu
[ 1.898711] TCP cubic registered
[ 1.898866] NET: Registered protocol family 10
[ 1.902515] Mobile IPv6
[ 1.902543] NET: Registered protocol family 17
[ 1.902574] Registering the dns_resolver key type
[ 1.902832] Using IPI No-Shortcut mode
[ 1.903315] PM: Hibernation image not present or could not be loaded.
[ 1.903399] registered taskstats version 1
[ 1.905643] rtc_cmos 00:04: setting system clock to 2013-06-07 08:55:09 UTC (1370595309)
[ 1.905802] Initializing network drop monitor service
[ 1.906827] Freeing unused kernel memory: 416k freed
[ 1.908690] Write protecting the kernel text: 2848k
[ 1.908815] Write protecting the kernel read-only data: 1096k
[ 1.908822] NX-protecting the kernel data: 3296k
[ 2.146067] udevd[44]: starting version 175
[ 2.220161] Refined TSC clocksource calibration: 1197.184 MHz.
[ 2.220224] Switching to clocksource tsc
[ 2.871847] SCSI subsystem initialized
[ 2.880961] usbcore: registered new interface driver usbfs
[ 2.881386] usbcore: registered new interface driver hub
[ 2.888240] usbcore: registered new device driver usb
[ 2.889685] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
[ 2.890246] ehci_hcd 0000:00:0f.3: EHCI Host Controller
[ 2.890451] ehci_hcd 0000:00:0f.3: new USB bus registered, assigned bus number 1
[ 2.891804] ehci_hcd 0000:00:0f.3: debug port 1
[ 2.895365] ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver
[ 2.918027] ehci_hcd 0000:00:0f.3: cache line size of 128 is not supported
[ 2.918110] ehci_hcd 0000:00:0f.3: irq 5, io mem 0xec204000
[ 2.952771] ehci_hcd 0000:00:0f.3: USB 2.0 started, EHCI 1.00
[ 2.953476] usb usb1: New USB device found, idVendor=1d6b, idProduct=0002
[ 2.953488] usb usb1: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[ 2.953497] usb usb1: Product: EHCI Host Controller
[ 2.953504] usb usb1: Manufacturer: Linux 3.2.0-4-686-pae ehci_hcd
[ 2.953512] usb usb1: SerialNumber: 0000:00:0f.3
[ 2.954631] hub 1-0:1.0: USB hub found
[ 2.954691] hub 1-0:1.0: 6 ports detected
[ 2.955887] ohci_hcd 0000:00:0f.0: OHCI Host Controller
[ 2.955968] ohci_hcd 0000:00:0f.0: new USB bus registered, assigned bus number 2
[ 2.956173] ohci_hcd 0000:00:0f.0: irq 3, io mem 0xec201000
[ 2.956518] libata version 3.00 loaded.
[ 2.975802] ACPI Error: [RBYT] Namespace lookup failure, AE_NOT_FOUND (20110623/psargs-359)
[ 2.975979] ACPI Error: Method parse/execution failed [\RTMP] (Node f602bb90), AE_NOT_FOUND (20110623/psparse-536)
[ 2.976144] ACPI Error: Method parse/execution failed [\_TZ_.THRM._TMP] (Node f602ba58), AE_NOT_FOUND (20110623/psparse-536)
[ 3.014948] usb usb2: New USB device found, idVendor=1d6b, idProduct=0001
[ 3.014962] usb usb2: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[ 3.014972] usb usb2: Product: OHCI Host Controller
[ 3.014979] usb usb2: Manufacturer: Linux 3.2.0-4-686-pae ohci_hcd
[ 3.014987] usb usb2: SerialNumber: 0000:00:0f.0
[ 3.016533] ACPI: Fan [FAN] (on)
[ 3.022501] via_rhine: v1.10-LK1.5.0 2010-10-09 Written by Donald Becker
[ 3.023492] ACPI: PCI Interrupt Link [LNK1] enabled at IRQ 11
[ 3.023509] PCI: setting IRQ 11 as level-triggered
[ 3.033502] hub 2-0:1.0: USB hub found
[ 3.033730] hub 2-0:1.0: 2 ports detected
[ 3.035399] ACPI: PCI Interrupt Link [LNK4] enabled at IRQ 10
[ 3.035415] PCI: setting IRQ 10 as level-triggered
[ 3.043649] scsi0 : pata_ali
[ 3.051206] scsi1 : pata_ali
[ 3.053056] ata1: PATA max UDMA/133 cmd 0x1f0 ctl 0x3f6 bmdma 0xf000 irq 14
[ 3.053074] ata2: PATA max UDMA/133 cmd 0x170 ctl 0x376 bmdma 0xf008 irq 15
[ 3.055285] ohci_hcd 0000:00:0f.1: OHCI Host Controller
[ 3.055374] ohci_hcd 0000:00:0f.1: new USB bus registered, assigned bus number 3
[ 3.055498] ohci_hcd 0000:00:0f.1: irq 3, io mem 0xec202000
[ 3.088856] via-rhine 0000:02:05.0: eth0: VIA Rhine III at 0x1d000, 00:13:21:ed:a5:4a, IRQ 11
[ 3.089786] via-rhine 0000:02:05.0: eth0: MII PHY found at address 1, status 0x786d advertising 05e1 Link 4de1
[ 3.110325] usb usb3: New USB device found, idVendor=1d6b, idProduct=0001
[ 3.110451] usb usb3: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[ 3.110463] usb usb3: Product: OHCI Host Controller
[ 3.110470] usb usb3: Manufacturer: Linux 3.2.0-4-686-pae ohci_hcd
[ 3.110478] usb usb3: SerialNumber: 0000:00:0f.1
[ 3.111073] hub 3-0:1.0: USB hub found
[ 3.111117] hub 3-0:1.0: 2 ports detected
[ 3.225637] ata1.00: CFA: 512MB ATA Flash Disk, ADAA328E, max MWDMA2
[ 3.225659] ata1.00: 1000944 sectors, multi 0: LBA
[ 3.232490] ata1.00: configured for MWDMA2
[ 3.234953] scsi 0:0:0:0: Direct-Access ATA 512MB ATA Fla ADAA PQ: 0 ANSI: 5
[ 3.264151] usb 1-3: new high-speed USB device number 2 using ehci_hcd
[ 3.408441] usb 1-3: New USB device found, idVendor=0403, idProduct=6011
[ 3.408455] usb 1-3: New USB device strings: Mfr=1, Product=2, SerialNumber=0
[ 3.408464] usb 1-3: Product: Quad RS232-HS
[ 3.408471] usb 1-3: Manufacturer: FTDI
[ 3.451692] sd 0:0:0:0: [sda] 1000944 512-byte logical blocks: (512 MB/488 MiB)
[ 3.453840] sd 0:0:0:0: [sda] Write Protect is off
[ 3.453852] sd 0:0:0:0: [sda] Mode Sense: 00 3a 00 00
[ 3.454627] sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
[ 3.464345] sda: sda1 sda2
[ 3.481936] sd 0:0:0:0: [sda] Attached SCSI disk
[ 3.492694] sd 0:0:0:0: Attached scsi generic sg0 type 0
[ 3.542432] usb 1-4: new high-speed USB device number 3 using ehci_hcd
[ 3.676184] usb 1-4: New USB device found, idVendor=13fe, idProduct=3800
[ 3.676199] usb 1-4: New USB device strings: Mfr=1, Product=2, SerialNumber=3
[ 3.676208] usb 1-4: Product: Patriot Memory
[ 3.676215] usb 1-4: Manufacturer:
[ 3.676222] usb 1-4: SerialNumber: 07012676A5B2FA18
[ 3.758286] Initializing USB Mass Storage driver...
[ 3.760826] scsi2 : usb-storage 1-4:1.0
[ 3.762844] usbcore: registered new interface driver usb-storage
[ 3.762857] USB Mass Storage support registered.
[ 4.765341] scsi 2:0:0:0: Direct-Access Patriot Memory PMAP PQ: 0 ANSI: 0 CCS
[ 4.782533] sd 2:0:0:0: [sdb] 15646720 512-byte logical blocks: (8.01 GB/7.46 GiB)
[ 4.782705] sd 2:0:0:0: Attached scsi generic sg1 type 0
[ 4.783749] sd 2:0:0:0: [sdb] Write Protect is off
[ 4.783764] sd 2:0:0:0: [sdb] Mode Sense: 23 00 00 00
[ 4.785496] sd 2:0:0:0: [sdb] No Caching mode page present
[ 4.785839] sd 2:0:0:0: [sdb] Assuming drive cache: write through
[ 4.792251] sd 2:0:0:0: [sdb] No Caching mode page present
[ 4.792346] sd 2:0:0:0: [sdb] Assuming drive cache: write through
[ 4.801754] sdb: sdb1
[ 4.811478] sd 2:0:0:0: [sdb] No Caching mode page present
[ 4.811575] sd 2:0:0:0: [sdb] Assuming drive cache: write through
[ 4.811644] sd 2:0:0:0: [sdb] Attached SCSI removable disk
[ 5.119869] kjournald starting. Commit interval 5 seconds
[ 5.120513] EXT3-fs (sdb1): mounted filesystem with ordered data mode
[ 6.772195] udevd[319]: starting version 175
[ 7.336514] input: Power Button as /devices/LNXSYSTM:00/LNXSYBUS:00/PNP0C0C:00/input/input0
[ 7.337070] ACPI: Power Button [PWRB]
[ 7.337828] input: Sleep Button as /devices/LNXSYSTM:00/LNXSYBUS:00/PNP0C0E:00/input/input1
[ 7.337945] ACPI: Sleep Button [SLPB]
[ 7.338362] input: Power Button as /devices/LNXSYSTM:00/LNXPWRBN:00/input/input2
[ 7.338401] ACPI: Power Button [PWRF]
[ 7.338770] input: Sleep Button as /devices/LNXSYSTM:00/LNXSLPBN:00/input/input3
[ 7.338871] ACPI: Sleep Button [SLPF]
[ 7.382820] shpchp: Standard Hot Plug PCI Controller Driver version: 0.4
[ 7.408916] ali1535_smbus 0000:00:03.1: ALI1535_smb region uninitialized - upgrade BIOS?
[ 7.408933] ali1535_smbus 0000:00:03.1: ALI1535 not detected, module not inserted.
[ 7.462756] ali1563_smbus 0000:00:03.0: Found ALi1563 SMBus at 0x5000
[ 7.468830] ali15x3_smbus 0000:00:03.1: ALI15X3_smb region uninitialized - upgrade BIOS or use force_addr=0xaddr
[ 7.469048] ali15x3_smbus 0000:00:03.1: ALI15X3 not detected, module not inserted.
[ 7.534621] alim7101_wdt: Steve Hill <steve@navaho.co.uk>.
[ 7.534677] alim7101_wdt: ALi 1543 South-Bridge not present - WDT not set
[ 7.605552] parport_pc 00:08: reported by Plug and Play ACPI
[ 7.605673] parport0: PC-style at 0x378 (0x778), irq 7 [PCSPP,TRISTATE]
[ 7.797402] ACPI: PCI Interrupt Link [LNK6] enabled at IRQ 10
[ 7.999916] input: PC Speaker as /devices/platform/pcspkr/input/input4
[ 8.021418] usbcore: registered new interface driver usbserial
[ 8.021479] USB Serial support registered for generic
[ 8.022030] usbcore: registered new interface driver usbserial_generic
[ 8.022050] usbserial: USB Serial Driver core
[ 8.023076] USB Serial support registered for FTDI USB Serial Device
[ 8.023362] ftdi_sio 1-3:1.0: FTDI USB Serial Device converter detected
[ 8.023517] usb 1-3: Detected FT4232H
[ 8.023528] usb 1-3: Number of endpoints 2
[ 8.023537] usb 1-3: Endpoint 1 MaxPacketSize 512
[ 8.023547] usb 1-3: Endpoint 2 MaxPacketSize 512
[ 8.023555] usb 1-3: Setting MaxPacketSize 512
[ 8.054658] usb 1-3: FTDI USB Serial Device converter now attached to ttyUSB0
[ 8.054824] ftdi_sio 1-3:1.1: FTDI USB Serial Device converter detected
[ 8.054965] usb 1-3: Detected FT4232H
[ 8.054976] usb 1-3: Number of endpoints 2
[ 8.054986] usb 1-3: Endpoint 1 MaxPacketSize 512
[ 8.054996] usb 1-3: Endpoint 2 MaxPacketSize 512
[ 8.055004] usb 1-3: Setting MaxPacketSize 512
[ 8.056754] Error: Driver 'pcspkr' is already registered, aborting...
[ 8.063745] usb 1-3: FTDI USB Serial Device converter now attached to ttyUSB1
[ 8.064501] ftdi_sio 1-3:1.2: FTDI USB Serial Device converter detected
[ 8.077129] usb 1-3: Detected FT4232H
[ 8.077143] usb 1-3: Number of endpoints 2
[ 8.077152] usb 1-3: Endpoint 1 MaxPacketSize 512
[ 8.077161] usb 1-3: Endpoint 2 MaxPacketSize 512
[ 8.077169] usb 1-3: Setting MaxPacketSize 512
[ 8.084317] usb 1-3: FTDI USB Serial Device converter now attached to ttyUSB2
[ 8.084742] ftdi_sio 1-3:1.3: FTDI USB Serial Device converter detected
[ 8.084990] usb 1-3: Detected FT4232H
[ 8.085000] usb 1-3: Number of endpoints 2
[ 8.085008] usb 1-3: Endpoint 1 MaxPacketSize 512
[ 8.085016] usb 1-3: Endpoint 2 MaxPacketSize 512
[ 8.085024] usb 1-3: Setting MaxPacketSize 512
[ 8.105510] usb 1-3: FTDI USB Serial Device converter now attached to ttyUSB3
[ 8.105679] usbcore: registered new interface driver ftdi_sio
[ 8.105688] ftdi_sio: v1.6.0:USB FTDI Serial Converters Driver
[ 8.136659] [drm] Initialized drm 1.1.0 20060810
[ 8.362694] [drm] radeon defaulting to kernel modesetting.
[ 8.362715] [drm] radeon kernel modesetting enabled.
[ 8.390109] [drm] initializing kernel modesetting (RV100 0x1002:0x5159 0x1002:0x5159).
[ 8.390538] [drm] register mmio base: 0xEC020000
[ 8.390548] [drm] register mmio size: 65536
[ 8.396359] agpgart-efficeon 0000:00:00.0: AGP 2.0 bridge
[ 8.404494] agpgart-efficeon 0000:00:00.0: putting AGP V2 device into 4x mode
[ 8.404599] radeon 0000:01:00.0: putting AGP V2 device into 4x mode
[ 8.404633] radeon 0000:01:00.0: GTT: 64M 0xE8000000 - 0xEBFFFFFF
[ 8.404674] radeon 0000:01:00.0: VRAM: 128M 0x00000000E0000000 - 0x00000000E7FFFFFF (16M used)
[ 8.407330] [drm] Supports vblank timestamp caching Rev 1 (10.10.2010).
[ 8.407342] [drm] Driver supports precise vblank timestamp query.
[ 8.407458] [drm] radeon: irq initialized.
[ 8.416384] [drm] Detected VRAM RAM=128M, BAR=128M
[ 8.416397] [drm] RAM width 32bits DDR
[ 8.423300] [TTM] Zone kernel: Available graphics memory: 448608 kiB
[ 8.423313] [TTM] Zone highmem: Available graphics memory: 504900 kiB
[ 8.423321] [TTM] Initializing pool allocator
[ 8.423355] [TTM] Initializing DMA pool allocator
[ 8.423718] [drm] radeon: 16M of VRAM memory ready
[ 8.423734] [drm] radeon: 64M of GTT memory ready.
[ 8.423882] [drm] radeon: ib pool ready.
[ 8.644119] agpgart: efficeon_insert_memory(0, 1)
[ 8.644135] [TTM] AGP Bind memory failed
[ 8.644572] radeon 0000:01:00.0: object_init failed for (4096, 0x00000002)
[ 8.644653] radeon 0000:01:00.0: (-22) create WB bo failed
[ 8.644663] radeon 0000:01:00.0: Disabling GPU acceleration
[ 8.644740] [drm] radeon: cp finalized
[ 8.644766] radeon 0000:01:00.0: f7256000 unpin not necessary
[ 8.645358] [drm] radeon: cp finalized
[ 8.645372] radeon 0000:01:00.0: no bo for sa manager
[ 8.645670] [TTM] Finalizing pool allocator
[ 8.696493] [TTM] Finalizing DMA pool allocator
[ 8.696761] [TTM] Zone kernel: Used memory at exit: 0 kiB
[ 8.696784] [TTM] Zone highmem: Used memory at exit: 0 kiB
[ 8.696800] [drm] radeon: ttm finalized
[ 8.696812] [drm] Forcing AGP to PCI mode
[ 8.697304] radeon 0000:01:00.0: VRAM: 128M 0x00000000E0000000 - 0x00000000E7FFFFFF (16M used)
[ 8.697320] radeon 0000:01:00.0: GTT: 512M 0x00000000C0000000 - 0x00000000DFFFFFFF
[ 8.697364] [drm] Supports vblank timestamp caching Rev 1 (10.10.2010).
[ 8.697371] [drm] Driver supports precise vblank timestamp query.
[ 8.697464] [drm] radeon: irq initialized.
[ 8.697514] [drm] Detected VRAM RAM=128M, BAR=128M
[ 8.697521] [drm] RAM width 32bits DDR
[ 8.707655] [TTM] Zone kernel: Available graphics memory: 448608 kiB
[ 8.707667] [TTM] Zone highmem: Available graphics memory: 504900 kiB
[ 8.707675] [TTM] Initializing pool allocator
[ 8.707702] [TTM] Initializing DMA pool allocator
[ 8.707935] [drm] radeon: 16M of VRAM memory ready
[ 8.707949] [drm] radeon: 512M of GTT memory ready.
[ 8.707984] [drm] GART: num cpu pages 131072, num gpu pages 131072
[ 8.767633] [drm] radeon: ib pool ready.
[ 8.793234] [drm] PCIE GART of 512M enabled (table at 0x0000000035880000).
[ 8.798562] radeon 0000:01:00.0: WB disabled
[ 8.798596] [drm] fence driver on ring 0 use gpu addr 0xc0000000 and cpu addr 0xf580c000
[ 8.798779] [drm] Loading R100 Microcode
[ 8.932697] AC'97 1 does not respond - RESET
[ 8.933369] AC'97 1 access is not valid [0xffffffff], removing mixer.
[ 8.933475] Unable to initialize codec #1
[ 8.936150] ali_codec_semaphore timeout
[ 8.945999] platform radeon_cp.0: firmware: agent aborted loading radeon/R100_cp.bin (not found?)
[ 8.946822] [drm:r100_cp_init] *ERROR* Failed to load firmware!
[ 8.946901] radeon 0000:01:00.0: failed initializing CP (-2).
[ 8.946966] radeon 0000:01:00.0: Disabling GPU acceleration
[ 8.947043] [drm] radeon: cp finalized
[ 8.947223] radeon 0000:01:00.0: f7252a00 unpin not necessary
[ 8.979892] [drm] Radeon Display Connectors
[ 8.979904] [drm] Connector 0:
[ 8.979910] [drm] VGA
[ 8.979918] [drm] DDC: 0x60 0x60 0x60 0x60 0x60 0x60 0x60 0x60
[ 8.979924] [drm] Encoders:
[ 8.979931] [drm] CRT1: INTERNAL_DAC1
[ 9.003339] intel8x0_measure_ac97_clock: measured 67053 usecs (3232 samples)
[ 9.003358] intel8x0: clocking to 48000
[ 9.011809] No connectors reported connected with modes
[ 9.011861] [drm] Cannot find any crtc or sizes - going 1024x768
[ 9.051121] [drm] fb mappable at 0xE0040000
[ 9.051134] [drm] vram apper at 0xE0000000
[ 9.051142] [drm] size 786432
[ 9.051147] [drm] fb depth is 8
[ 9.051153] [drm] pitch is 1024
[ 9.056458] fbcon: radeondrmfb (fb0) is primary device
[ 9.088859] Console: switching to colour frame buffer device 128x48
[ 9.101419] fb0: radeondrmfb frame buffer device
[ 9.101429] drm: registered panic notifier
[ 9.101493] [drm] Initialized radeon 2.16.0 20080528 for 0000:01:00.0 on minor 0
[ 10.463024] EXT3-fs (sdb1): using internal journal
[ 10.647638] loop: module loaded
[ 14.031164] via-rhine 0000:02:05.0: eth0: link up, 100Mbps, full-duplex, lpa 0x4DE1
[ 14.837347] RPC: Registered named UNIX socket transport module.
[ 14.837370] RPC: Registered udp transport module.
[ 14.837380] RPC: Registered tcp transport module.
[ 14.837390] RPC: Registered tcp NFSv4.1 backchannel transport module.
[ 14.868816] FS-Cache: Loaded
[ 14.935730] FS-Cache: Netfs 'nfs' registered for caching
[ 14.966188] Installing knfsd (copyright (C) 1996 [EMAIL="okir@monad.swb.de"]okir@monad.swb.de[/EMAIL]).
[ 24.696050] eth0: no IPv6 routers present
W ogóle nie widać w logach modemu. Sprawdź jeszcze ten link: http://wiki.debian.org/udev (podrozdział "Persistent Device name").
Kod: Zaznacz cały
SUBSYSTEMS=="usb", KERNEL=="ttyUSB*", ID=="1-3:1.0", ATTRS{bInterfaceNumber}=="00", SYMLINK+="quad-2-1"
SUBSYSTEMS=="usb", KERNEL=="ttyUSB*", ID=="1-3:1.1", ATTRS{bInterfaceNumber}=="01", SYMLINK+="quad-2-2"
SUBSYSTEMS=="usb", KERNEL=="ttyUSB*", ID=="1-3:1.2", ATTRS{bInterfaceNumber}=="02", SYMLINK+="quad-2-3"
SUBSYSTEMS=="usb", KERNEL=="ttyUSB*", ID=="1-3:1.3", ATTRS{bInterfaceNumber}=="03", SYMLINK+="quad-2-4"Kod: Zaznacz cały
lrwxrwxrwx 1 root root 7 05-27 04:00 quad-2-1 -> ttyUSB4
lrwxrwxrwx 1 root root 7 05-27 04:00 quad-2-2 -> ttyUSB5
lrwxrwxrwx 1 root root 7 05-27 04:00 quad-2-3 -> ttyUSB6
lrwxrwxrwx 1 root root 7 05-27 04:00 quad-2-4 -> ttyUSB7
Kod: Zaznacz cały
root@debian:~# ls -l /dev
razem 0
crw-rw---T 1 root video 10, 175 cze 7 10:55 agpgart
crw------T 1 root root 10, 235 cze 7 10:55 autofs
drwxr-xr-x 2 root root 300 cze 7 08:55 block
drwxr-xr-x 2 root root 80 cze 7 10:55 bsg
crw------T 1 root root 10, 234 cze 7 10:55 btrfs-control
drwxr-xr-x 3 root root 60 cze 7 10:55 bus
drwxr-xr-x 2 root root 2700 cze 7 08:55 char
crw------- 1 root root 5, 1 cze 7 08:55 console
lrwxrwxrwx 1 root root 11 cze 7 10:55 core -> /proc/kcore
drwxr-xr-x 2 root root 60 cze 7 10:55 cpu
crw------- 1 root root 10, 62 cze 7 08:55 cpu_dma_latency
drwxr-xr-x 6 root root 120 cze 7 10:55 disk
drwxr-xr-x 2 root root 80 cze 7 08:55 dri
crw-rw---T 1 root video 29, 0 cze 7 08:55 fb0
lrwxrwxrwx 1 root root 13 cze 7 10:55 fd -> /proc/self/fd
crw-rw-rw- 1 root root 1, 7 cze 7 10:55 full
crw------T 1 root root 10, 229 cze 7 10:55 fuse
crw------- 1 root root 10, 228 cze 7 10:55 hpet
drwxr-xr-x 3 root root 180 cze 7 08:55 input
crw------- 1 root root 1, 11 cze 7 10:55 kmsg
srw-rw-rw- 1 root root 0 cze 7 08:55 log
brw-rw---T 1 root disk 7, 0 cze 7 08:55 loop0
brw-rw---T 1 root disk 7, 1 cze 7 08:55 loop1
brw-rw---T 1 root disk 7, 2 cze 7 08:55 loop2
brw-rw---T 1 root disk 7, 3 cze 7 08:55 loop3
brw-rw---T 1 root disk 7, 4 cze 7 08:55 loop4
brw-rw---T 1 root disk 7, 5 cze 7 08:55 loop5
brw-rw---T 1 root disk 7, 6 cze 7 08:55 loop6
brw-rw---T 1 root disk 7, 7 cze 7 08:55 loop7
crw------T 1 root root 10, 237 cze 7 08:55 loop-control
lrwxrwxrwx 1 root root 9 cze 7 10:55 MAKEDEV -> /bin/true
drwxr-xr-x 2 root root 60 cze 7 10:55 mapper
crw------- 1 root root 10, 227 cze 7 10:55 mcelog
crw-r----T 1 root kmem 1, 1 cze 7 10:55 mem
drwxr-xr-x 2 root root 60 cze 7 10:55 net
crw------- 1 root root 10, 61 cze 7 10:55 network_latency
crw------- 1 root root 10, 60 cze 7 10:55 network_throughput
crw-rw-rw- 1 root root 1, 3 cze 7 10:55 null
crw------- 1 root root 1, 12 cze 7 10:55 oldmem
crw-r----T 1 root kmem 1, 4 cze 7 10:55 port
crw------T 1 root root 108, 0 cze 7 10:55 ppp
crw------- 1 root root 10, 1 cze 7 08:55 psaux
crw-rw-rw- 1 root root 5, 2 cze 7 21:04 ptmx
drwxr-xr-x 2 root root 0 cze 7 10:55 pts
crw-rw-rw- 1 root root 1, 8 cze 7 10:55 random
lrwxrwxrwx 1 root root 4 cze 7 08:55 root -> sdb1
lrwxrwxrwx 1 root root 4 cze 7 10:55 rtc -> rtc0
crw------- 1 root root 254, 0 cze 7 10:55 rtc0
brw-rw---T 1 root disk 8, 0 cze 7 08:55 sda
brw-rw---T 1 root disk 8, 1 cze 7 08:55 sda1
brw-rw---T 1 root disk 8, 2 cze 7 08:55 sda2
brw-rw---T 1 root floppy 8, 16 cze 7 08:55 sdb
brw-rw---T 1 root floppy 8, 17 cze 7 08:55 sdb1
drwxr-xr-x 4 root root 80 cze 7 08:55 serial
crw------- 1 root root 21, 0 cze 7 10:55 sg0
crw------- 1 root root 21, 1 cze 7 10:55 sg1
lrwxrwxrwx 1 root root 8 cze 7 08:55 shm -> /run/shm
crw------- 1 root root 10, 231 cze 7 08:55 snapshot
drwxr-xr-x 3 root root 200 cze 7 08:55 snd
lrwxrwxrwx 1 root root 24 cze 7 08:55 sndstat -> /proc/asound/oss/sndstat
lrwxrwxrwx 1 root root 15 cze 7 10:55 stderr -> /proc/self/fd/2
lrwxrwxrwx 1 root root 15 cze 7 10:55 stdin -> /proc/self/fd/0
lrwxrwxrwx 1 root root 15 cze 7 10:55 stdout -> /proc/self/fd/1
crw-rw-rw- 1 root root 5, 0 cze 7 08:55 tty
crw------- 1 root root 4, 0 cze 7 08:55 tty0
crw-rw---- 1 root tty 4, 1 cze 7 08:55 tty1
crw------- 1 root root 4, 10 cze 7 08:55 tty10
crw------- 1 root root 4, 11 cze 7 08:55 tty11
crw------- 1 root root 4, 12 cze 7 08:55 tty12
crw------- 1 root root 4, 13 cze 7 08:55 tty13
crw------- 1 root root 4, 14 cze 7 08:55 tty14
crw------- 1 root root 4, 15 cze 7 08:55 tty15
crw------- 1 root root 4, 16 cze 7 08:55 tty16
crw------- 1 root root 4, 17 cze 7 08:55 tty17
crw------- 1 root root 4, 18 cze 7 08:55 tty18
crw------- 1 root root 4, 19 cze 7 08:55 tty19
crw-rw---- 1 root tty 4, 2 cze 7 08:55 tty2
crw------- 1 root root 4, 20 cze 7 08:55 tty20
crw------- 1 root root 4, 21 cze 7 08:55 tty21
crw------- 1 root root 4, 22 cze 7 08:55 tty22
crw------- 1 root root 4, 23 cze 7 08:55 tty23
crw------- 1 root root 4, 24 cze 7 08:55 tty24
crw------- 1 root root 4, 25 cze 7 08:55 tty25
crw------- 1 root root 4, 26 cze 7 08:55 tty26
crw------- 1 root root 4, 27 cze 7 08:55 tty27
crw------- 1 root root 4, 28 cze 7 08:55 tty28
crw------- 1 root root 4, 29 cze 7 08:55 tty29
crw-rw---- 1 root tty 4, 3 cze 7 08:55 tty3
crw------- 1 root root 4, 30 cze 7 08:55 tty30
crw------- 1 root root 4, 31 cze 7 08:55 tty31
crw------- 1 root root 4, 32 cze 7 08:55 tty32
crw------- 1 root root 4, 33 cze 7 08:55 tty33
crw------- 1 root root 4, 34 cze 7 08:55 tty34
crw------- 1 root root 4, 35 cze 7 08:55 tty35
crw------- 1 root root 4, 36 cze 7 08:55 tty36
crw------- 1 root root 4, 37 cze 7 08:55 tty37
crw------- 1 root root 4, 38 cze 7 08:55 tty38
crw------- 1 root root 4, 39 cze 7 08:55 tty39
crw-rw---- 1 root tty 4, 4 cze 7 08:55 tty4
crw------- 1 root root 4, 40 cze 7 08:55 tty40
crw------- 1 root root 4, 41 cze 7 08:55 tty41
crw------- 1 root root 4, 42 cze 7 08:55 tty42
crw------- 1 root root 4, 43 cze 7 08:55 tty43
crw------- 1 root root 4, 44 cze 7 08:55 tty44
crw------- 1 root root 4, 45 cze 7 08:55 tty45
crw------- 1 root root 4, 46 cze 7 08:55 tty46
crw------- 1 root root 4, 47 cze 7 08:55 tty47
crw------- 1 root root 4, 48 cze 7 08:55 tty48
crw------- 1 root root 4, 49 cze 7 08:55 tty49
crw-rw---- 1 root tty 4, 5 cze 7 08:55 tty5
crw------- 1 root root 4, 50 cze 7 08:55 tty50
crw------- 1 root root 4, 51 cze 7 08:55 tty51
crw------- 1 root root 4, 52 cze 7 08:55 tty52
crw------- 1 root root 4, 53 cze 7 08:55 tty53
crw------- 1 root root 4, 54 cze 7 08:55 tty54
crw------- 1 root root 4, 55 cze 7 08:55 tty55
crw------- 1 root root 4, 56 cze 7 08:55 tty56
crw------- 1 root root 4, 57 cze 7 08:55 tty57
crw------- 1 root root 4, 58 cze 7 08:55 tty58
crw------- 1 root root 4, 59 cze 7 08:55 tty59
crw-rw---- 1 root tty 4, 6 cze 7 08:55 tty6
crw------- 1 root root 4, 60 cze 7 08:55 tty60
crw------- 1 root root 4, 61 cze 7 08:55 tty61
crw------- 1 root root 4, 62 cze 7 08:55 tty62
crw------- 1 root root 4, 63 cze 7 08:55 tty63
crw------- 1 root root 4, 7 cze 7 08:55 tty7
crw------- 1 root root 4, 8 cze 7 08:55 tty8
crw------- 1 root root 4, 9 cze 7 08:55 tty9
crw-rw---T 1 root dialout 4, 64 cze 7 10:55 ttyS0
crw-rw---T 1 root dialout 4, 65 cze 7 10:55 ttyS1
crw-rw---T 1 root dialout 4, 66 cze 7 10:55 ttyS2
crw-rw---T 1 root dialout 4, 67 cze 7 10:55 ttyS3
crw-rw---T 1 root dialout 188, 0 cze 7 08:55 ttyUSB0
crw-rw---T 1 root dialout 188, 1 cze 7 08:55 ttyUSB1
crw-rw---T 1 root dialout 188, 2 cze 7 08:55 ttyUSB2
crw-rw---T 1 root dialout 188, 3 cze 7 15:41 ttyUSB3
crw------T 1 root root 10, 223 cze 7 10:55 uinput
crw-rw-rw- 1 root root 1, 9 cze 7 10:55 urandom
crw------- 1 root root 7, 0 cze 7 08:55 vcs
crw------- 1 root root 7, 1 cze 7 08:55 vcs1
crw------- 1 root root 7, 2 cze 7 08:55 vcs2
crw------- 1 root root 7, 3 cze 7 08:55 vcs3
crw------- 1 root root 7, 4 cze 7 08:55 vcs4
crw------- 1 root root 7, 5 cze 7 08:55 vcs5
crw------- 1 root root 7, 6 cze 7 08:55 vcs6
crw------- 1 root root 7, 128 cze 7 08:55 vcsa
crw------- 1 root root 7, 129 cze 7 08:55 vcsa1
crw------- 1 root root 7, 130 cze 7 08:55 vcsa2
crw------- 1 root root 7, 131 cze 7 08:55 vcsa3
crw------- 1 root root 7, 132 cze 7 08:55 vcsa4
crw------- 1 root root 7, 133 cze 7 08:55 vcsa5
crw------- 1 root root 7, 134 cze 7 08:55 vcsa6
crw------- 1 root root 10, 63 cze 7 08:55 vga_arbiter
prw-r----- 1 root adm 0 cze 7 21:03 xconsole
crw-rw-rw- 1 root root 1, 5 cze 7 10:55 zero
Pewnie wystarczy tylko zmodyfikować reguły, wklej tu wyniki poleceń (jako root):
Kod: Zaznacz cały
udevadm info --name=/dev/ttyUSB0 --attribute-walk
udevadm info --name=/dev/ttyUSB1 --attribute-walk