Wszystko związane z jądrem systemowym, sterownikami, sprzętem itp.
regu
Posty: 16 Rejestracja: 04 września 2015, 21:44
Lokalizacja: Poznań
Post
autor: regu » 06 września 2015, 17:38
Pewnie, dzięki za przypomnienie
Też próbowałem go włączać i wyłączać w różnych konfiguracjach ale tylko Bluetooth się aktywuje. Może to cały czas nie te sterowniki? Zauktualizowałem repozytoria, jak proponowałeś, i jest to samo co wcześniej:
Kod: Zaznacz cały
[color=#000000][font=Cantarell]# aptitude install firmware-iwlwifi
Nie zostaną zainstalowane, zaktualizowane ani usunięte żadne pakiety.
0 pakietów aktualizowanych, 0 instalowanych, 0 do usunięcia i 54 nieaktualizowanych.
Do pobrania 0 B archiwów. Zajęte po rozpakowaniu: 0 B.
[/font][/color]
[color=#000000][font=Cantarell]
[/font][/color]
[color=#000000][font=Cantarell]# ifconfig wlan0 up
wlan0: ERROR while getting interface flags: Nie ma takiego urządzenia
No i co tu zrobić żeby poniżej pojawiło się wlan0?
Kod: Zaznacz cały
eth0 Link encap:Ethernet HWaddr 00:18:8b:de:28:d9
inet addr:192.168.0.104 Bcast:192.168.0.255 Mask:255.255.255.0
inet6 addr: fe80::218:8bff:fede:28d9/64 Scope:Link
UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1
RX packets:3253 errors:0 dropped:0 overruns:0 frame:0
TX packets:2429 errors:0 dropped:0 overruns:0 carrier:0
collisions:0 txqueuelen:1000
RX bytes:1543279 (1.4 MiB) TX bytes:383822 (374.8 KiB)
Interrupt:17
lo Link encap:Local Loopback
inet addr:127.0.0.1 Mask:255.0.0.0
inet6 addr: ::1/128 Scope:Host
UP LOOPBACK RUNNING MTU:65536 Metric:1
RX packets:44 errors:0 dropped:0 overruns:0 frame:0
TX packets:44 errors:0 dropped:0 overruns:0 carrier:0
collisions:0 txqueuelen:0
RX bytes:5302 (5.1 KiB) TX bytes:5302 (5.1 KiB)
[/font][/color]
ww71
Beginner
Posty: 443 Rejestracja: 04 grudnia 2008, 11:44
Lokalizacja: lubelskie
Post
autor: ww71 » 06 września 2015, 17:49
Wklej jeszcze raz cały wynik:
oraz:
można by jeszcze sprawdzić w Biosie, czy jest wifi wlaczone.
regu
Posty: 16 Rejestracja: 04 września 2015, 21:44
Lokalizacja: Poznań
Post
autor: regu » 06 września 2015, 18:01
OK, słusznie. Sprawdzę co tam w BIOSie.
Pozniżej wyniki:
Kod: Zaznacz cały
# lspci -k
00:00.0 Host bridge: Intel Corporation Mobile PM965/GM965/GL960 Memory Controller Hub (rev 0c)
Subsystem: Dell Device 01f9
00:01.0 PCI bridge: Intel Corporation Mobile PM965/GM965/GL960 PCI Express Root Port (rev 0c)
Kernel driver in use: pcieport
00:1a.0 USB controller: Intel Corporation 82801H (ICH8 Family) USB UHCI Controller #4 (rev 02)
Subsystem: Dell Device 01f9
Kernel driver in use: uhci_hcd
00:1a.1 USB controller: Intel Corporation 82801H (ICH8 Family) USB UHCI Controller #5 (rev 02)
Subsystem: Dell Device 01f9
Kernel driver in use: uhci_hcd
00:1a.7 USB controller: Intel Corporation 82801H (ICH8 Family) USB2 EHCI Controller #2 (rev 02)
Subsystem: Dell Device 01f9
Kernel driver in use: ehci-pci
00:1b.0 Audio device: Intel Corporation 82801H (ICH8 Family) HD Audio Controller (rev 02)
Subsystem: Dell Dell Latitude D630
Kernel driver in use: snd_hda_intel
00:1c.0 PCI bridge: Intel Corporation 82801H (ICH8 Family) PCI Express Port 1 (rev 02)
Kernel driver in use: pcieport
00:1c.1 PCI bridge: Intel Corporation 82801H (ICH8 Family) PCI Express Port 2 (rev 02)
Kernel driver in use: pcieport
00:1c.5 PCI bridge: Intel Corporation 82801H (ICH8 Family) PCI Express Port 6 (rev 02)
Kernel driver in use: pcieport
00:1d.0 USB controller: Intel Corporation 82801H (ICH8 Family) USB UHCI Controller #1 (rev 02)
Subsystem: Dell Device 01f9
Kernel driver in use: uhci_hcd
00:1d.1 USB controller: Intel Corporation 82801H (ICH8 Family) USB UHCI Controller #2 (rev 02)
Subsystem: Dell Device 01f9
Kernel driver in use: uhci_hcd
00:1d.2 USB controller: Intel Corporation 82801H (ICH8 Family) USB UHCI Controller #3 (rev 02)
Subsystem: Dell Device 01f9
Kernel driver in use: uhci_hcd
00:1d.7 USB controller: Intel Corporation 82801H (ICH8 Family) USB2 EHCI Controller #1 (rev 02)
Subsystem: Dell Device 01f9
Kernel driver in use: ehci-pci
00:1e.0 PCI bridge: Intel Corporation 82801 Mobile PCI Bridge (rev f2)
00:1f.0 ISA bridge: Intel Corporation 82801HM (ICH8M) LPC Interface Controller (rev 02)
Subsystem: Dell Device 01f9
Kernel driver in use: lpc_ich
00:1f.1 IDE interface: Intel Corporation 82801HM/HEM (ICH8M/ICH8M-E) IDE Controller (rev 02)
Subsystem: Dell Device 01f9
Kernel driver in use: ata_piix
00:1f.2 IDE interface: Intel Corporation 82801HM/HEM (ICH8M/ICH8M-E) SATA Controller [IDE mode] (rev 02)
Subsystem: Dell Device 01f9
Kernel driver in use: ata_piix
00:1f.3 SMBus: Intel Corporation 82801H (ICH8 Family) SMBus Controller (rev 02)
Subsystem: Dell Device 01f9
Kernel driver in use: i801_smbus
01:00.0 VGA compatible controller: NVIDIA Corporation G86M [Quadro NVS 135M] (rev a1)
Subsystem: Dell Device 01f9
Kernel driver in use: nouveau
03:01.0 CardBus bridge: O2 Micro, Inc. Cardbus bridge (rev 21)
Subsystem: Dell Device 01f9
Kernel driver in use: yenta_cardbus
03:01.4 FireWire (IEEE 1394): O2 Micro, Inc. Firewire (IEEE 1394) (rev 02)
Subsystem: Dell Device 01f9
Kernel driver in use: firewire_ohci
09:00.0 Ethernet controller: Broadcom Corporation NetXtreme BCM5755M Gigabit Ethernet PCI Express (rev 02)
Subsystem: Dell Device 01f9
Kernel driver in use: tg3
0c:00.0 Network controller: Broadcom Corporation BCM4311 802.11a/b/g (rev 01)
Subsystem: Dell Wireless 1490 Dual Band WLAN Mini-Card
Kod: Zaznacz cały
# cat /etc/apt/sources.list
deb http://ftp.pl.debian.org/debian/ jessie main non-free contrib
deb-src http://ftp.pl.debian.org/debian/ jessie main non-free contrib
deb http://security.debian.org/ jessie/updates main contrib non-free
deb-src http://security.debian.org/ jessie/updates main contrib non-free
# jessie-updates, previously known as 'volatile'
deb http://ftp.pl.debian.org/debian/ jessie-updates main contrib non-free
deb-src http://ftp.pl.debian.org/debian/ jessie-updates main contrib non-free
# backports
deb http://ftp.pl.debian.org/debian/ jessie-backports main contrib non-free
regu
Posty: 16 Rejestracja: 04 września 2015, 21:44
Lokalizacja: Poznań
Post
autor: regu » 06 września 2015, 18:10
BIOS sprawdzony. W "Wireless" wszystko Enabled, więc jest OK.
ww71
Beginner
Posty: 443 Rejestracja: 04 grudnia 2008, 11:44
Lokalizacja: lubelskie
Post
autor: ww71 » 06 września 2015, 18:12
No tak, masz inną karte wifi niż u mnie:
Kod: Zaznacz cały
Network controller: Broadcom Corporation BCM4311 802.11a/b/g (rev 01)
Subsystem: Dell Wireless 1490 Dual Band WLAN Mini-Card
Może ktoś inny pomoże, ja na razie nie znam sterowników do niej.
A może spróbuj tego sterownika:
Kod: Zaznacz cały
aptitude install b43-fwcutter firmware-b43-installer
regu
Posty: 16 Rejestracja: 04 września 2015, 21:44
Lokalizacja: Poznań
Post
autor: regu » 06 września 2015, 18:57
Dzięki za pomoc. Jeszcze się nie poddaję.
Próbowałem też z tymi sterownikami i to samo:
Kod: Zaznacz cały
# aptitude install b43-fwcutter firmware-b43-installer
Nie zostaną zainstalowane, zaktualizowane ani usunięte żadne pakiety.
0 pakietów aktualizowanych, 0 instalowanych, 0 do usunięcia i 0 nieaktualizowanych.
Do pobrania 0 B archiwów. Zajęte po rozpakowaniu: 0 B.
Czy to znaczy że już to mam zainstalowane? bo już sie zamotałem...
ww71
Beginner
Posty: 443 Rejestracja: 04 grudnia 2008, 11:44
Lokalizacja: lubelskie
Post
autor: ww71 » 06 września 2015, 19:08
Właśnie nie zostały zainstalowane, i nie wiem dlaczego. Repo masz ok. według mnie. Jeśli masz synaptica (jest to instalator pakietów graficzny w zakładce : system), to znajdź tam pakiet: b43-fwcutter i tam go zainstaluj.
regu
Posty: 16 Rejestracja: 04 września 2015, 21:44
Lokalizacja: Poznań
Post
autor: regu » 06 września 2015, 20:29
Sprawdziłem w synapticu i jest zainstalowane. Zrobiłem tam też reinstall i nic... nie chce działać i tyle.
Będę wdzięczny za jakieś wskazówki co jeszcze można zrobić?
Załącznik Synaptic _b43.jpg nie jest już dostępny
Załączniki
ww71
Beginner
Posty: 443 Rejestracja: 04 grudnia 2008, 11:44
Lokalizacja: lubelskie
Post
autor: ww71 » 06 września 2015, 20:45
W sumie nie mam więcej pomysłów. Może sprubój jeszcze zainstalować ten następny pakiet:
bo jego też wymieniali na jednej stronie. nastepnie przeładuj kompa. I ewnetualnie:
regu
Posty: 16 Rejestracja: 04 września 2015, 21:44
Lokalizacja: Poznań
Post
autor: regu » 19 września 2015, 21:49
witam ponownie,
Jeszcze się nie poddałem, a wifi jak nie było, tak nie ma. Ponawiam prośbę o pomoc. czy wiecie jak zmusić do działania
Kod: Zaznacz cały
0c:00.0 Network controller: Broadcom Corporation BCM4311 802.11a/b/g (rev 01)
mam zainstalowane sterowniki: b43-fwcutter, firmware-b43-installer
ale cały czas dla iwconfig jest to:
Kod: Zaznacz cały
lo no wireless extensions.
eth0 no wireless extensions.
i o co tu chodzi?