Kod: Zaznacz cały
wlan0 Interface doesn't support scanning: Network is down[+] Debian 32bit z LXDE konfiguracja sieci bezprzewodowej
Przedstaw wyniki:
Kod: Zaznacz cały
lspci -k
dmesgKod: Zaznacz cały
root@debian:~# lspci -k
00:00.0 Host bridge: Intel Corporation Mobile 945GM/PM/GMS, 943/940GML and 945GT Express Memory Controller Hub (rev 03)
Subsystem: Toshiba America Info Systems Device ff31
Kernel driver in use: agpgart-intel
00:02.0 VGA compatible controller: Intel Corporation Mobile 945GM/GMS, 943/940GML Express Integrated Graphics Controller (rev 03)
Subsystem: Toshiba America Info Systems Device ff31
Kernel driver in use: i915
00:02.1 Display controller: Intel Corporation Mobile 945GM/GMS/GME, 943/940GML Express Integrated Graphics Controller (rev 03)
Subsystem: Toshiba America Info Systems Device ff31
00:1b.0 Audio device: Intel Corporation N10/ICH 7 Family High Definition Audio Controller (rev 02)
Subsystem: Toshiba America Info Systems AC97 Data Fax SoftModem with SmartCP
Kernel driver in use: HDA Intel
00:1c.0 PCI bridge: Intel Corporation N10/ICH 7 Family PCI Express Port 1 (rev 02)
Kernel driver in use: pcieport
00:1c.1 PCI bridge: Intel Corporation N10/ICH 7 Family PCI Express Port 2 (rev 02)
Kernel driver in use: pcieport
00:1c.2 PCI bridge: Intel Corporation N10/ICH 7 Family PCI Express Port 3 (rev 02)
Kernel driver in use: pcieport
00:1d.0 USB Controller: Intel Corporation N10/ICH 7 Family USB UHCI Controller #1 (rev 02)
Subsystem: Toshiba America Info Systems Device ff31
Kernel driver in use: uhci_hcd
00:1d.1 USB Controller: Intel Corporation N10/ICH 7 Family USB UHCI Controller #2 (rev 02)
Subsystem: Toshiba America Info Systems Device ff31
Kernel driver in use: uhci_hcd
00:1d.2 USB Controller: Intel Corporation N10/ICH 7 Family USB UHCI Controller #3 (rev 02)
Subsystem: Toshiba America Info Systems Device ff31
Kernel driver in use: uhci_hcd
00:1d.3 USB Controller: Intel Corporation N10/ICH 7 Family USB UHCI Controller #4 (rev 02)
Subsystem: Toshiba America Info Systems Device ff31
Kernel driver in use: uhci_hcd
00:1d.7 USB Controller: Intel Corporation N10/ICH 7 Family USB2 EHCI Controller (rev 02)
Subsystem: Toshiba America Info Systems Device ff31
Kernel driver in use: ehci_hcd
00:1e.0 PCI bridge: Intel Corporation 82801 Mobile PCI Bridge (rev e2)
00:1f.0 ISA bridge: Intel Corporation 82801GBM (ICH7-M) LPC Interface Bridge (rev 02)
Subsystem: Toshiba America Info Systems Device ff31
00:1f.2 IDE interface: Intel Corporation 82801GBM/GHM (ICH7 Family) SATA IDE Controller (rev 02)
Subsystem: Toshiba America Info Systems Device ff31
Kernel driver in use: ata_piix
00:1f.3 SMBus: Intel Corporation N10/ICH 7 Family SMBus Controller (rev 02)
Subsystem: Toshiba America Info Systems Device ff31
03:00.0 Network controller: Intel Corporation PRO/Wireless 3945ABG [Golan] Network Connection (rev 02)
Subsystem: Intel Corporation PRO/Wireless 3945ABG Network Connection
Kernel driver in use: iwl3945
0a:04.0 CardBus bridge: Texas Instruments PCIxx12 Cardbus Controller
Subsystem: Toshiba America Info Systems Device ff31
Kernel driver in use: yenta_cardbus
0a:04.1 FireWire (IEEE 1394): Texas Instruments PCIxx12 OHCI Compliant IEEE 1394 Host Controller
Subsystem: Toshiba America Info Systems Device ff31
Kernel driver in use: firewire_ohci
0a:04.2 Mass storage controller: Texas Instruments 5-in-1 Multimedia Card Reader (SD/MMC/MS/MS PRO/xD)
Subsystem: Toshiba America Info Systems Device ff31
Kernel driver in use: tifm_7xx1
0a:04.3 SD Host controller: Texas Instruments PCIxx12 SDA Standard Compliant SD Host Controller
Subsystem: Toshiba America Info Systems Device ff31
Kernel driver in use: sdhci-pci
0a:08.0 Ethernet controller: Intel Corporation PRO/100 VE Network Connection (rev 02)
Subsystem: Toshiba America Info Systems Device ff31
Kernel driver in use: e100Kod: Zaznacz cały
root@debian:~# dmesg
[ 0.000000] Initializing cgroup subsys cpuset
[ 0.000000] Initializing cgroup subsys cpu
[ 0.000000] Linux version 2.6.32-5-686 (Debian 2.6.32-46) (dannf@debian.org) (gcc version 4.3.5 (Debian 4.3.5-4) ) #1 SMP Sun Sep 23 09:49:36 UTC 2012
[ 0.000000] KERNEL supported cpus:
[ 0.000000] Intel GenuineIntel
[ 0.000000] AMD AuthenticAMD
[ 0.000000] NSC Geode by NSC
[ 0.000000] Cyrix CyrixInstead
[ 0.000000] Centaur CentaurHauls
[ 0.000000] Transmeta GenuineTMx86
[ 0.000000] Transmeta TransmetaCPU
[ 0.000000] UMC UMC UMC UMC
[ 0.000000] BIOS-provided physical RAM map:
[ 0.000000] BIOS-e820: 0000000000000000 - 000000000009f800 (usable)
[ 0.000000] BIOS-e820: 000000000009f800 - 00000000000a0000 (reserved)
[ 0.000000] BIOS-e820: 00000000000dc000 - 00000000000e4000 (reserved)
[ 0.000000] BIOS-e820: 00000000000e8000 - 0000000000100000 (reserved)
[ 0.000000] BIOS-e820: 0000000000100000 - 000000003f690000 (usable)
[ 0.000000] BIOS-e820: 000000003f690000 - 000000003f69c000 (ACPI data)
[ 0.000000] BIOS-e820: 000000003f69c000 - 000000003f700000 (ACPI NVS)
[ 0.000000] BIOS-e820: 000000003f700000 - 0000000040000000 (reserved)
[ 0.000000] BIOS-e820: 00000000e0000000 - 00000000f0000000 (reserved)
[ 0.000000] BIOS-e820: 00000000fec00000 - 00000000fec10000 (reserved)
[ 0.000000] BIOS-e820: 00000000fed00000 - 00000000fed00400 (reserved)
[ 0.000000] BIOS-e820: 00000000fed14000 - 00000000fed1a000 (reserved)
[ 0.000000] BIOS-e820: 00000000fed1c000 - 00000000fed90000 (reserved)
[ 0.000000] BIOS-e820: 00000000fee00000 - 00000000fee01000 (reserved)
[ 0.000000] BIOS-e820: 00000000ff000000 - 0000000100000000 (reserved)
[ 0.000000] DMI present.
[ 0.000000] last_pfn = 0x3f690 max_arch_pfn = 0x100000
[ 0.000000] MTRR default type: uncachable
[ 0.000000] MTRR fixed ranges enabled:
[ 0.000000] 00000-9FFFF write-back
[ 0.000000] A0000-BFFFF uncachable
[ 0.000000] C0000-CFFFF write-protect
[ 0.000000] D0000-DFFFF uncachable
[ 0.000000] E0000-FFFFF write-protect
[ 0.000000] MTRR variable ranges enabled:
[ 0.000000] 0 base 000000000 mask FC0000000 write-back
[ 0.000000] 1 base 03F700000 mask FFFF00000 uncachable
[ 0.000000] 2 base 03F800000 mask FFF800000 uncachable
[ 0.000000] 3 disabled
[ 0.000000] 4 disabled
[ 0.000000] 5 disabled
[ 0.000000] 6 disabled
[ 0.000000] 7 disabled
[ 0.000000] x86 PAT enabled: cpu 0, old 0x7040600070406, new 0x7010600070106
[ 0.000000] initial memory mapped : 0 - 01800000
[ 0.000000] init_memory_mapping: 0000000000000000-00000000373fe000
[ 0.000000] 0000000000 - 0000400000 page 4k
[ 0.000000] 0000400000 - 0037000000 page 2M
[ 0.000000] 0037000000 - 00373fe000 page 4k
[ 0.000000] kernel direct mapping tables up to 373fe000 @ 7000-d000
[ 0.000000] RAMDISK: 2f0de000 - 2f92b321
[ 0.000000] ACPI: RSDP 000f75d0 00024 (v02 TOSQCI)
[ 0.000000] ACPI: XSDT 3f692072 00074 (v01 TOSQCI TOSQCI00 06040000 LTP 00000000)
[ 0.000000] ACPI: FACP 3f69bc2a 000F4 (v03 TOSQCI TOSQCI00 06040000 ALAN 00000001)
[ 0.000000] ACPI: DSDT 3f69311a 08A9C (v01 TOSQCI Denver 06040000 MSFT 03000001)
[ 0.000000] ACPI: FACS 3f69cfc0 00040
[ 0.000000] ACPI: APIC 3f69bd1e 00068 (v01 TOSQCI TOSQCI00 06040000 LOHR 0000005A)
[ 0.000000] ACPI: HPET 3f69bd86 00038 (v01 TOSQCI TOSQCI00 06040000 LOHR 0000005A)
[ 0.000000] ACPI: MCFG 3f69bdbe 0003C (v01 TOSQCI TOSQCI00 06040000 LOHR 0000005A)
[ 0.000000] ACPI: APIC 3f69bdfa 00068 (v01 PTLTD ? APIC 06040000 LTP 00000000)
[ 0.000000] ACPI: BOOT 3f69be62 00028 (v01 PTLTD $SBFTBL$ 06040000 LTP 00000001)
[ 0.000000] ACPI: SLIC 3f69be8a 00176 (v01 TOSQCI TOSQCI00 06040000 LTP 00000000)
[ 0.000000] ACPI: SSDT 3f692672 0025F (v01 PmRef Cpu0Tst 00003000 INTL 20060912)
[ 0.000000] ACPI: SSDT 3f6925cc 000A6 (v01 PmRef Cpu1Tst 00003000 INTL 20060912)
[ 0.000000] ACPI: SSDT 3f6920e6 004E6 (v01 PmRef CpuPm 00003000 INTL 20060912)
[ 0.000000] ACPI: BIOS bug: multiple APIC/MADT found, using 0
[ 0.000000] ACPI: If "acpi_apic_instance=2" works better, notify linux-acpi@vger.kernel.org
[ 0.000000] ACPI: Local APIC address 0xfee00000
[ 0.000000] 130MB HIGHMEM available.
[ 0.000000] 883MB LOWMEM available.
[ 0.000000] mapped low ram: 0 - 373fe000
[ 0.000000] low ram: 0 - 373fe000
[ 0.000000] node 0 low ram: 00000000 - 373fe000
[ 0.000000] node 0 bootmap 00009000 - 0000fe80
[ 0.000000] (9 early reservations) ==> bootmem [0000000000 - 00373fe000]
[ 0.000000] #0 [0000000000 - 0000001000] BIOS data page ==> [0000000000 - 0000001000]
[ 0.000000] #1 [0000001000 - 0000002000] EX TRAMPOLINE ==> [0000001000 - 0000002000]
[ 0.000000] #2 [0000006000 - 0000007000] TRAMPOLINE ==> [0000006000 - 0000007000]
[ 0.000000] #3 [0001000000 - 00014ccd0c] TEXT DATA BSS ==> [0001000000 - 00014ccd0c]
[ 0.000000] #4 [002f0de000 - 002f92b321] RAMDISK ==> [002f0de000 - 002f92b321]
[ 0.000000] #5 [000009f800 - 0000100000] BIOS reserved ==> [000009f800 - 0000100000]
[ 0.000000] #6 [00014cd000 - 00014d313c] BRK ==> [00014cd000 - 00014d313c]
[ 0.000000] #7 [0000007000 - 0000009000] PGTABLE ==> [0000007000 - 0000009000]
[ 0.000000] #8 [0000009000 - 0000010000] BOOTMAP ==> [0000009000 - 0000010000]
[ 0.000000] found SMP MP-table at [c00f7690] f7690
[ 0.000000] Zone PFN ranges:
[ 0.000000] DMA 0x00000000 -> 0x00001000
[ 0.000000] Normal 0x00001000 -> 0x000373fe
[ 0.000000] HighMem 0x000373fe -> 0x0003f690
[ 0.000000] Movable zone start PFN for each node
[ 0.000000] early_node_map[2] active PFN ranges
[ 0.000000] 0: 0x00000000 -> 0x0000009f
[ 0.000000] 0: 0x00000100 -> 0x0003f690
[ 0.000000] On node 0 totalpages: 259631
[ 0.000000] free_area_init_node: node 0, pgdat c13b48c0, node_mem_map c14d5000
[ 0.000000] DMA zone: 32 pages used for memmap
[ 0.000000] DMA zone: 0 pages reserved
[ 0.000000] DMA zone: 3967 pages, LIFO batch:0
[ 0.000000] Normal zone: 1736 pages used for memmap
[ 0.000000] Normal zone: 220470 pages, LIFO batch:31
[ 0.000000] HighMem zone: 262 pages used for memmap
[ 0.000000] HighMem zone: 33164 pages, LIFO batch:7
[ 0.000000] Using APIC driver default
[ 0.000000] ACPI: PM-Timer IO Port: 0x1008
[ 0.000000] ACPI: Local APIC address 0xfee00000
[ 0.000000] ACPI: LAPIC (acpi_id[0x00] lapic_id[0x00] enabled)
[ 0.000000] ACPI: LAPIC (acpi_id[0x01] lapic_id[0x01] enabled)
[ 0.000000] ACPI: LAPIC_NMI (acpi_id[0x00] high edge lint[0x1])
[ 0.000000] ACPI: LAPIC_NMI (acpi_id[0x01] high edge lint[0x1])
[ 0.000000] ACPI: IOAPIC (id[0x01] address[0xfec00000] gsi_base[0])
[ 0.000000] IOAPIC[0]: apic_id 1, version 32, address 0xfec00000, GSI 0-23
[ 0.000000] ACPI: INT_SRC_OVR (bus 0 bus_irq 0 global_irq 2 dfl dfl)
[ 0.000000] ACPI: INT_SRC_OVR (bus 0 bus_irq 9 global_irq 9 high level)
[ 0.000000] ACPI: IRQ0 used by override.
[ 0.000000] ACPI: IRQ2 used by override.
[ 0.000000] ACPI: IRQ9 used by override.
[ 0.000000] Using ACPI (MADT) for SMP configuration information
[ 0.000000] ACPI: HPET id: 0x8086a201 base: 0xfed00000
[ 0.000000] SMP: Allowing 2 CPUs, 0 hotplug CPUs
[ 0.000000] nr_irqs_gsi: 24
[ 0.000000] PM: Registered nosave memory: 000000000009f000 - 00000000000a0000
[ 0.000000] PM: Registered nosave memory: 00000000000a0000 - 00000000000dc000
[ 0.000000] PM: Registered nosave memory: 00000000000dc000 - 00000000000e4000
[ 0.000000] PM: Registered nosave memory: 00000000000e4000 - 00000000000e8000
[ 0.000000] PM: Registered nosave memory: 00000000000e8000 - 0000000000100000
[ 0.000000] Allocating PCI resources starting at 40000000 (gap: 40000000:a0000000)
[ 0.000000] Booting paravirtualized kernel on bare hardware
[ 0.000000] NR_CPUS:32 nr_cpumask_bits:32 nr_cpu_ids:2 nr_node_ids:1
[ 0.000000] PERCPU: Embedded 14 pages/cpu @c2000000 s34328 r0 d23016 u2097152
[ 0.000000] pcpu-alloc: s34328 r0 d23016 u2097152 alloc=1*4194304
[ 0.000000] pcpu-alloc: [0] 0 1
[ 0.000000] Built 1 zonelists in Zone order, mobility grouping on. Total pages: 257601
[ 0.000000] Kernel command line: BOOT_IMAGE=/boot/vmlinuz-2.6.32-5-686 root=UUID=d32e954a-04bc-46fb-b2d6-0ee4bf22f1ae ro quiet
[ 0.000000] PID hash table entries: 4096 (order: 2, 16384 bytes)
[ 0.000000] Dentry cache hash table entries: 131072 (order: 7, 524288 bytes)
[ 0.000000] Inode-cache hash table entries: 65536 (order: 6, 262144 bytes)
[ 0.000000] Enabling fast FPU save and restore... done.
[ 0.000000] Enabling unmasked SIMD FPU exception support... done.
[ 0.000000] Initializing CPU#0
[ 0.000000] Initializing HighMem for node 0 (000373fe:0003f690)
[ 0.000000] Memory: 1015312k/1038912k available (2506k kernel code, 22540k reserved, 1326k data, 380k init, 133704k highmem)
[ 0.000000] virtual kernel memory layout:
[ 0.000000] fixmap : 0xffd56000 - 0xfffff000 (2724 kB)
[ 0.000000] pkmap : 0xff400000 - 0xff800000 (4096 kB)
[ 0.000000] vmalloc : 0xf7bfe000 - 0xff3fe000 ( 120 MB)
[ 0.000000] lowmem : 0xc0000000 - 0xf73fe000 ( 883 MB)
[ 0.000000] .init : 0xc13bf000 - 0xc141e000 ( 380 kB)
[ 0.000000] .data : 0xc1272b9b - 0xc13be4c4 (1326 kB)
[ 0.000000] .text : 0xc1000000 - 0xc1272b9b (2506 kB)
[ 0.000000] Checking if this processor honours the WP bit even in supervisor mode...Ok.
[ 0.000000] SLUB: Genslabs=13, HWalign=64, Order=0-3, MinObjects=0, CPUs=2, Nodes=1
[ 0.000000] Hierarchical RCU implementation.
[ 0.000000] NR_IRQS:1280
[ 0.000000] Extended CMOS year: 2000
[ 0.000000] Console: colour VGA+ 80x25
[ 0.000000] console [tty0] enabled
[ 0.000000] hpet clockevent registered
[ 0.000000] Fast TSC calibration using PIT
[ 0.000000] Detected 1600.095 MHz processor.
[ 0.004005] Calibrating delay loop (skipped), value calculated using timer frequency.. 3200.19 BogoMIPS (lpj=6400380)
[ 0.004020] Security Framework initialized
[ 0.004025] SELinux: Disabled at boot.
[ 0.004032] Mount-cache hash table entries: 512
[ 0.004157] Initializing cgroup subsys ns
[ 0.004161] Initializing cgroup subsys cpuacct
[ 0.004166] Initializing cgroup subsys devices
[ 0.004169] Initializing cgroup subsys freezer
[ 0.004171] Initializing cgroup subsys net_cls
[ 0.004194] CPU: L1 I cache: 32K, L1 D cache: 32K
[ 0.004197] CPU: L2 cache: 2048K
[ 0.004200] CPU: Physical Processor ID: 0
[ 0.004202] CPU: Processor Core ID: 0
[ 0.004207] mce: CPU supports 6 MCE banks
[ 0.004215] CPU0: Thermal monitoring handled by SMI
[ 0.004219] using mwait in idle threads.
[ 0.004225] Performance Events: Core2 events, Intel PMU driver.
[ 0.004231] ... version: 2
[ 0.004233] ... bit width: 40
[ 0.004235] ... generic registers: 2
[ 0.004237] ... value mask: 000000ffffffffff
[ 0.004239] ... max period: 000000007fffffff
[ 0.004241] ... fixed-purpose events: 3
[ 0.004243] ... event mask: 0000000700000003
[ 0.004247] Checking 'hlt' instruction... OK.
[ 0.021406] ACPI: Core revision 20090903
[ 0.021410] TOSHIBA Satellite detected - force copy of DSDT to local memory
[ 0.026273] ACPI: Forced DSDT copy: length 0x08A9C copied locally, original unmapped
[ 0.032069] Enabling APIC mode: Flat. Using 1 I/O APICs
[ 0.032461] ..TIMER: vector=0x30 apic1=0 pin1=2 apic2=-1 pin2=-1
[ 0.072541] CPU0: Intel(R) Core(TM)2 CPU T5200 @ 1.60GHz stepping 06
[ 0.076001] Booting processor 1 APIC 0x1 ip 0x6000
[ 0.008000] Initializing CPU#1
[ 0.008000] CPU: L1 I cache: 32K, L1 D cache: 32K
[ 0.008000] CPU: L2 cache: 2048K
[ 0.008000] CPU: Physical Processor ID: 0
[ 0.008000] CPU: Processor Core ID: 1
[ 0.008000] CPU1: Thermal monitoring handled by SMI
[ 0.160094] CPU1: Intel(R) Core(TM)2 CPU T5200 @ 1.60GHz stepping 06
[ 0.160105] checking TSC synchronization [CPU#0 -> CPU#1]: passed.
[ 0.164063] Brought up 2 CPUs
[ 0.164066] Total of 2 processors activated (6400.34 BogoMIPS).
[ 0.165062] CPU0 attaching sched-domain:
[ 0.165068] domain 0: span 0-1 level MC
[ 0.165071] groups: group c2003778 cpus 0 group c2203778 cpus 1
[ 0.165079] CPU1 attaching sched-domain:
[ 0.165082] domain 0: span 0-1 level MC
[ 0.165085] groups: group c2203778 cpus 1 group c2003778 cpus 0
[ 0.165155] devtmpfs: initialized
[ 0.165155] regulator: core version 0.5
[ 0.165155] NET: Registered protocol family 16
[ 0.165155] ACPI: bus type pci registered
[ 0.165155] PCI: MCFG configuration 0: base e0000000 segment 0 buses 0 - 255
[ 0.165155] PCI: MCFG area at e0000000 reserved in E820
[ 0.165155] PCI: Using MMCONFIG for extended config space
[ 0.165155] PCI: Using configuration type 1 for base access
[ 0.165155] bio: create slab <bio-0> at 0
[ 0.165155] ACPI: EC: Look up EC in DSDT
[ 0.171275] ACPI: BIOS _OSI(Linux) query ignored
[ 0.172072] ACPI: EC: GPE storm detected, transactions will use polling mode
[ 0.324074] ACPI: Interpreter enabled
[ 0.324078] ACPI: (supports S0 S3 S4 S5)
[ 0.324103] ACPI: Using IOAPIC for interrupt routing
[ 0.329944] ACPI: EC: GPE = 0x17, I/O: command/status = 0x66, data = 0x62
[ 0.330286] ACPI: No dock devices found.
[ 0.330641] ACPI: PCI Root Bridge [PCI0] (0000:00)
[ 0.330757] pci 0000:00:02.0: reg 10 32bit mmio: [0xd0200000-0xd027ffff]
[ 0.330763] pci 0000:00:02.0: reg 14 io port: [0x1800-0x1807]
[ 0.330770] pci 0000:00:02.0: reg 18 32bit mmio pref: [0xc0000000-0xcfffffff]
[ 0.330776] pci 0000:00:02.0: reg 1c 32bit mmio: [0xd0300000-0xd033ffff]
[ 0.330835] pci 0000:00:02.1: reg 10 32bit mmio: [0xd0280000-0xd02fffff]
[ 0.330974] pci 0000:00:1b.0: reg 10 64bit mmio: [0xd0340000-0xd0343fff]
[ 0.331065] pci 0000:00:1b.0: PME# supported from D0 D3hot D3cold
[ 0.331071] pci 0000:00:1b.0: PME# disabled
[ 0.331202] pci 0000:00:1c.0: PME# supported from D0 D3hot D3cold
[ 0.331208] pci 0000:00:1c.0: PME# disabled
[ 0.331341] pci 0000:00:1c.1: PME# supported from D0 D3hot D3cold
[ 0.331346] pci 0000:00:1c.1: PME# disabled
[ 0.331479] pci 0000:00:1c.2: PME# supported from D0 D3hot D3cold
[ 0.331485] pci 0000:00:1c.2: PME# disabled
[ 0.331560] pci 0000:00:1d.0: reg 20 io port: [0x1820-0x183f]
[ 0.331638] pci 0000:00:1d.1: reg 20 io port: [0x1840-0x185f]
[ 0.331713] pci 0000:00:1d.2: reg 20 io port: [0x1860-0x187f]
[ 0.331789] pci 0000:00:1d.3: reg 20 io port: [0x1880-0x189f]
[ 0.331869] pci 0000:00:1d.7: reg 10 32bit mmio: [0xd0544000-0xd05443ff]
[ 0.331960] pci 0000:00:1d.7: PME# supported from D0 D3hot D3cold
[ 0.331967] pci 0000:00:1d.7: PME# disabled
[ 0.332183] pci 0000:00:1f.0: quirk: region 1000-107f claimed by ICH6 ACPI/GPIO/TCO
[ 0.332191] pci 0000:00:1f.0: quirk: region 1180-11bf claimed by ICH6 GPIO
[ 0.332197] pci 0000:00:1f.0: ICH7 LPC Generic IO decode 1 PIO at 0680 (mask 007f)
[ 0.332202] pci 0000:00:1f.0: ICH7 LPC Generic IO decode 2 PIO at 1600 (mask 007f)
[ 0.332207] pci 0000:00:1f.0: ICH7 LPC Generic IO decode 3 PIO at 0500 (mask 000f)
[ 0.332212] pci 0000:00:1f.0: ICH7 LPC Generic IO decode 4 PIO at 0068 (mask 0007)
[ 0.332303] pci 0000:00:1f.2: reg 10 io port: [0x00-0x07]
[ 0.332313] pci 0000:00:1f.2: reg 14 io port: [0x00-0x03]
[ 0.332322] pci 0000:00:1f.2: reg 18 io port: [0x00-0x07]
[ 0.332331] pci 0000:00:1f.2: reg 1c io port: [0x00-0x03]
[ 0.332340] pci 0000:00:1f.2: reg 20 io port: [0x18b0-0x18bf]
[ 0.332393] pci 0000:00:1f.2: PME# supported from D3hot
[ 0.332398] pci 0000:00:1f.2: PME# disabled
[ 0.332470] pci 0000:00:1f.3: reg 20 io port: [0x18c0-0x18df]
[ 0.332577] pci 0000:00:1c.0: bridge io port: [0x00-0xfff]
[ 0.332583] pci 0000:00:1c.0: bridge 32bit mmio: [0x000000-0x0fffff]
[ 0.332592] pci 0000:00:1c.0: bridge 64bit mmio pref: [0x000000-0x0fffff]
[ 0.332742] pci 0000:03:00.0: reg 10 32bit mmio: [0x000000-0x000fff]
[ 0.333073] pci 0000:03:00.0: PME# supported from D0 D3hot D3cold
[ 0.333087] pci 0000:03:00.0: PME# disabled
[ 0.333197] pci 0000:03:00.0: disabling ASPM on pre-1.1 PCIe device. You can enable it with 'pcie_aspm=force'
[ 0.333364] pci 0000:00:1c.1: bridge io port: [0x00-0xfff]
[ 0.333370] pci 0000:00:1c.1: bridge 32bit mmio: [0x000000-0x0fffff]
[ 0.333379] pci 0000:00:1c.1: bridge 64bit mmio pref: [0x000000-0x0fffff]
[ 0.333446] pci 0000:00:1c.2: bridge io port: [0x00-0xfff]
[ 0.333452] pci 0000:00:1c.2: bridge 32bit mmio: [0x000000-0x0fffff]
[ 0.333461] pci 0000:00:1c.2: bridge 64bit mmio pref: [0x000000-0x0fffff]
[ 0.333523] pci 0000:0a:04.0: reg 10 32bit mmio: [0xd0004000-0xd0004fff]
[ 0.333570] pci 0000:0a:04.0: supports D1 D2
[ 0.333573] pci 0000:0a:04.0: PME# supported from D0 D1 D2 D3hot D3cold
[ 0.333579] pci 0000:0a:04.0: PME# disabled
[ 0.333634] pci 0000:0a:04.1: reg 10 32bit mmio: [0xd0007000-0xd00077ff]
[ 0.333645] pci 0000:0a:04.1: reg 14 32bit mmio: [0xd0000000-0xd0003fff]
[ 0.333731] pci 0000:0a:04.1: supports D1 D2
[ 0.333733] pci 0000:0a:04.1: PME# supported from D0 D1 D2 D3hot
[ 0.333740] pci 0000:0a:04.1: PME# disabled
[ 0.333792] pci 0000:0a:04.2: reg 10 32bit mmio: [0xd0005000-0xd0005fff]
[ 0.333882] pci 0000:0a:04.2: supports D1 D2
[ 0.333885] pci 0000:0a:04.2: PME# supported from D0 D1 D2 D3hot
[ 0.333891] pci 0000:0a:04.2: PME# disabled
[ 0.333944] pci 0000:0a:04.3: reg 10 32bit mmio: [0xd0007800-0xd00078ff]
[ 0.334033] pci 0000:0a:04.3: supports D1 D2
[ 0.334035] pci 0000:0a:04.3: PME# supported from D0 D1 D2 D3hot
[ 0.334042] pci 0000:0a:04.3: PME# disabled
[ 0.334110] pci 0000:0a:08.0: reg 10 32bit mmio: [0xd0006000-0xd0006fff]
[ 0.334119] pci 0000:0a:08.0: reg 14 io port: [0x2000-0x203f]
[ 0.334191] pci 0000:0a:08.0: supports D1 D2
[ 0.334194] pci 0000:0a:08.0: PME# supported from D0 D1 D2 D3hot D3cold
[ 0.334199] pci 0000:0a:08.0: PME# disabled
[ 0.334262] pci 0000:00:1e.0: transparent bridge
[ 0.334268] pci 0000:00:1e.0: bridge io port: [0x2000-0x2fff]
[ 0.334274] pci 0000:00:1e.0: bridge 32bit mmio: [0xd0000000-0xd00fffff]
[ 0.334333] pci_bus 0000:00: on NUMA node 0
[ 0.334338] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0._PRT]
[ 0.334533] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.RP01._PRT]
[ 0.334613] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.RP02._PRT]
[ 0.334692] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.RP03._PRT]
[ 0.334802] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.PCIB._PRT]
[ 0.344022] ACPI: PCI Interrupt Link [LNKA] (IRQs 1 3 4 5 6 7 10 12 14 15) *11
[ 0.344125] ACPI: PCI Interrupt Link [LNKB] (IRQs 1 3 4 5 6 7 *11 12 14 15)
[ 0.344224] ACPI: PCI Interrupt Link [LNKC] (IRQs 1 3 4 5 6 7 10 12 14 15) *11
[ 0.344323] ACPI: PCI Interrupt Link [LNKD] (IRQs 1 3 4 5 6 7 *11 12 14 15)
[ 0.344420] ACPI: PCI Interrupt Link [LNKE] (IRQs 1 3 4 5 6 7 10 12 14 15) *11
[ 0.344519] ACPI: PCI Interrupt Link [LNKF] (IRQs 1 3 4 5 6 7 11 12 14 15) *0, disabled.
[ 0.344617] ACPI: PCI Interrupt Link [LNKG] (IRQs 1 3 4 5 6 7 10 12 14 15) *11
[ 0.344715] ACPI: PCI Interrupt Link [LNKH] (IRQs 1 3 4 5 6 *7 11 12 14 15)
[ 0.344819] vgaarb: device added: PCI:0000:00:02.0,decodes=io+mem,owns=io+mem,locks=none
[ 0.344836] vgaarb: loaded
[ 0.344854] PCI: Using ACPI for IRQ routing
[ 0.344854] pci 0000:00:1c.0: BAR 13: can't allocate resource
[ 0.344854] pci 0000:00:1c.0: BAR 14: can't allocate resource
[ 0.344854] pci 0000:00:1c.0: BAR 15: can't allocate resource
[ 0.344854] pci 0000:00:1c.1: BAR 13: can't allocate resource
[ 0.344854] pci 0000:00:1c.1: BAR 14: can't allocate resource
[ 0.344854] pci 0000:00:1c.1: BAR 15: can't allocate resource
[ 0.344854] pci 0000:00:1c.2: BAR 13: can't allocate resource
[ 0.344854] pci 0000:00:1c.2: BAR 14: can't allocate resource
[ 0.344854] pci 0000:00:1c.2: BAR 15: can't allocate resource
[ 0.344854] HPET: 3 timers in total, 0 timers will be used for per-cpu timer
[ 0.344854] hpet0: at MMIO 0xfed00000, IRQs 2, 8, 0
[ 0.344854] hpet0: 3 comparators, 64-bit 14.318180 MHz counter
[ 0.348023] Switching to clocksource tsc
[ 0.349667] pnp: PnP ACPI init
[ 0.349677] ACPI: bus type pnp registered
[ 0.351850] pnp: PnP ACPI: found 9 devices
[ 0.351853] ACPI: ACPI bus type pnp unregistered
[ 0.351857] PnPBIOS: Disabled by ACPI PNP
[ 0.351869] system 00:01: iomem range 0xe0000000-0xefffffff has been reserved
[ 0.351873] system 00:01: iomem range 0xfed14000-0xfed17fff has been reserved
[ 0.351877] system 00:01: iomem range 0xfed18000-0xfed18fff has been reserved
[ 0.351881] system 00:01: iomem range 0xfed19000-0xfed19fff has been reserved
[ 0.351885] system 00:01: iomem range 0xfed1c000-0xfed1ffff has been reserved
[ 0.351889] system 00:01: iomem range 0xfed20000-0xfed3ffff has been reserved
[ 0.351893] system 00:01: iomem range 0xfed45000-0xfed8ffff has been reserved
[ 0.351901] system 00:03: iomem range 0xfed00000-0xfed003ff has been reserved
[ 0.351909] system 00:05: ioport range 0x680-0x68f has been reserved
[ 0.351913] system 00:05: ioport range 0x800-0x80f has been reserved
[ 0.351917] system 00:05: ioport range 0x1000-0x107f has been reserved
[ 0.351920] system 00:05: ioport range 0x1180-0x11bf has been reserved
[ 0.351927] system 00:05: ioport range 0x1620-0x162f has been reserved
[ 0.351931] system 00:05: ioport range 0x1640-0x164f has been reserved
[ 0.351935] system 00:05: ioport range 0xfe10-0xfe11 has been reserved
[ 0.351939] system 00:05: ioport range 0xfe00-0xfe00 has been reserved
[ 0.386771] pci 0000:00:1c.0: PCI bridge, secondary bus 0000:02
[ 0.386776] pci 0000:00:1c.0: IO window: 0x3000-0x3fff
[ 0.386784] pci 0000:00:1c.0: MEM window: 0x44000000-0x441fffff
[ 0.386791] pci 0000:00:1c.0: PREFETCH window: 0x00000044200000-0x000000443fffff
[ 0.386812] pci 0000:00:1c.1: PCI bridge, secondary bus 0000:03
[ 0.386818] pci 0000:00:1c.1: IO window: 0x4000-0x4fff
[ 0.386825] pci 0000:00:1c.1: MEM window: 0x44400000-0x445fffff
[ 0.386831] pci 0000:00:1c.1: PREFETCH window: 0x00000044600000-0x000000447fffff
[ 0.386841] pci 0000:00:1c.2: PCI bridge, secondary bus 0000:04
[ 0.386845] pci 0000:00:1c.2: IO window: 0x5000-0x5fff
[ 0.386853] pci 0000:00:1c.2: MEM window: 0x44800000-0x449fffff
[ 0.386859] pci 0000:00:1c.2: PREFETCH window: 0x00000044a00000-0x00000044bfffff
[ 0.386872] pci 0000:0a:04.0: CardBus bridge, secondary bus 0000:0b
[ 0.386875] pci 0000:0a:04.0: IO window: 0x002400-0x0024ff
[ 0.386881] pci 0000:0a:04.0: IO window: 0x002800-0x0028ff
[ 0.386888] pci 0000:0a:04.0: PREFETCH window: 0x40000000-0x43ffffff
[ 0.386895] pci 0000:0a:04.0: MEM window: 0x48000000-0x4bffffff
[ 0.386901] pci 0000:00:1e.0: PCI bridge, secondary bus 0000:0a
[ 0.386906] pci 0000:00:1e.0: IO window: 0x2000-0x2fff
[ 0.386914] pci 0000:00:1e.0: MEM window: 0xd0000000-0xd00fffff
[ 0.386920] pci 0000:00:1e.0: PREFETCH window: 0x40000000-0x43ffffff
[ 0.386938] pci 0000:00:1c.0: enabling device (0000 -> 0003)
[ 0.386948] pci 0000:00:1c.0: PCI INT A -> GSI 17 (level, low) -> IRQ 17
[ 0.386956] pci 0000:00:1c.0: setting latency timer to 64
[ 0.386967] pci 0000:00:1c.1: enabling device (0000 -> 0003)
[ 0.386974] pci 0000:00:1c.1: PCI INT B -> GSI 16 (level, low) -> IRQ 16
[ 0.386981] pci 0000:00:1c.1: setting latency timer to 64
[ 0.386993] pci 0000:00:1c.2: enabling device (0000 -> 0003)
[ 0.386999] pci 0000:00:1c.2: PCI INT C -> GSI 18 (level, low) -> IRQ 18
[ 0.387006] pci 0000:00:1c.2: setting latency timer to 64
[ 0.387013] pci 0000:00:1e.0: enabling device (0004 -> 0007)
[ 0.387020] pci 0000:00:1e.0: setting latency timer to 64
[ 0.387033] pci 0000:0a:04.0: enabling device (0000 -> 0003)
[ 0.387038] pci 0000:0a:04.0: PCI INT A -> GSI 17 (level, low) -> IRQ 17
[ 0.387047] pci 0000:0a:04.0: setting latency timer to 64
[ 0.387053] pci_bus 0000:00: resource 0 io: [0x00-0xffff]
[ 0.387056] pci_bus 0000:00: resource 1 mem: [0x000000-0xffffffff]
[ 0.387060] pci_bus 0000:02: resource 0 io: [0x3000-0x3fff]
[ 0.387063] pci_bus 0000:02: resource 1 mem: [0x44000000-0x441fffff]
[ 0.387067] pci_bus 0000:02: resource 2 pref mem [0x44200000-0x443fffff]
[ 0.387070] pci_bus 0000:03: resource 0 io: [0x4000-0x4fff]
[ 0.387073] pci_bus 0000:03: resource 1 mem: [0x44400000-0x445fffff]
[ 0.387077] pci_bus 0000:03: resource 2 pref mem [0x44600000-0x447fffff]
[ 0.387080] pci_bus 0000:04: resource 0 io: [0x5000-0x5fff]
[ 0.387083] pci_bus 0000:04: resource 1 mem: [0x44800000-0x449fffff]
[ 0.387087] pci_bus 0000:04: resource 2 pref mem [0x44a00000-0x44bfffff]
[ 0.387090] pci_bus 0000:0a: resource 0 io: [0x2000-0x2fff]
[ 0.387093] pci_bus 0000:0a: resource 1 mem: [0xd0000000-0xd00fffff]
[ 0.387097] pci_bus 0000:0a: resource 2 pref mem [0x40000000-0x43ffffff]
[ 0.387100] pci_bus 0000:0a: resource 3 io: [0x00-0xffff]
[ 0.387103] pci_bus 0000:0a: resource 4 mem: [0x000000-0xffffffff]
[ 0.387106] pci_bus 0000:0b: resource 0 io: [0x2400-0x24ff]
[ 0.387109] pci_bus 0000:0b: resource 1 io: [0x2800-0x28ff]
[ 0.387112] pci_bus 0000:0b: resource 2 pref mem [0x40000000-0x43ffffff]
[ 0.387116] pci_bus 0000:0b: resource 3 mem: [0x48000000-0x4bffffff]
[ 0.387150] NET: Registered protocol family 2
[ 0.387246] IP route cache hash table entries: 32768 (order: 5, 131072 bytes)
[ 0.387585] TCP established hash table entries: 131072 (order: 8, 1048576 bytes)
[ 0.388156] TCP bind hash table entries: 65536 (order: 7, 524288 bytes)
[ 0.388433] TCP: Hash tables configured (established 131072 bind 65536)
[ 0.388436] TCP reno registered
[ 0.388523] NET: Registered protocol family 1
[ 0.388545] pci 0000:00:02.0: Boot video device
[ 0.388570] pci 0000:00:1d.0: PCI INT A -> GSI 23 (level, low) -> IRQ 23
[ 0.388593] pci 0000:00:1d.0: PCI INT A disabled
[ 0.388603] pci 0000:00:1d.1: PCI INT B -> GSI 19 (level, low) -> IRQ 19
[ 0.388625] pci 0000:00:1d.1: PCI INT B disabled
[ 0.388633] pci 0000:00:1d.2: PCI INT C -> GSI 18 (level, low) -> IRQ 18
[ 0.388656] pci 0000:00:1d.2: PCI INT C disabled
[ 0.388663] pci 0000:00:1d.3: PCI INT D -> GSI 16 (level, low) -> IRQ 16
[ 0.388685] pci 0000:00:1d.3: PCI INT D disabled
[ 0.388700] pci 0000:00:1d.7: PCI INT A -> GSI 23 (level, low) -> IRQ 23
[ 1.988010] pci 0000:00:1d.7: EHCI: BIOS handoff failed (BIOS bug?) 01010001
[ 1.988125] pci 0000:00:1d.7: PCI INT A disabled
[ 1.988157] pci 0000:0a:08.0: Firmware left e100 interrupts enabled; disabling
[ 1.988218] Unpacking initramfs...
[ 2.290403] Freeing initrd memory: 8500k freed
[ 2.296301] Simple Boot Flag at 0x36 set to 0x1
[ 2.296686] audit: initializing netlink socket (disabled)
[ 2.296705] type=2000 audit(1153051517.296:1): initialized
[ 2.301142] highmem bounce pool size: 64 pages
[ 2.301148] HugeTLB registered 4 MB page size, pre-allocated 0 pages
[ 2.302860] VFS: Disk quotas dquot_6.5.2
[ 2.302924] Dquot-cache hash table entries: 1024 (order 0, 4096 bytes)
[ 2.303021] msgmni has been set to 1739
[ 2.303286] alg: No test for stdrng (krng)
[ 2.303352] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 253)
[ 2.303356] io scheduler noop registered
[ 2.303358] io scheduler anticipatory registered
[ 2.303361] io scheduler deadline registered
[ 2.303405] io scheduler cfq registered (default)
[ 2.303586] pcieport 0000:00:1c.0: irq 24 for MSI/MSI-X
[ 2.303600] pcieport 0000:00:1c.0: setting latency timer to 64
[ 2.303779] pcieport 0000:00:1c.1: irq 25 for MSI/MSI-X
[ 2.303791] pcieport 0000:00:1c.1: setting latency timer to 64
[ 2.303971] pcieport 0000:00:1c.2: irq 26 for MSI/MSI-X
[ 2.303983] pcieport 0000:00:1c.2: setting latency timer to 64
[ 2.304201] isapnp: Scanning for PnP cards...
[ 2.658276] isapnp: No Plug & Play device found
[ 2.659941] Linux agpgart interface v0.103
[ 2.660046] agpgart-intel 0000:00:00.0: Intel 945GM Chipset
[ 2.660798] agpgart-intel 0000:00:00.0: detected 7932K stolen memory
[ 2.664310] agpgart-intel 0000:00:00.0: AGP aperture is 256M @ 0xc0000000
[ 2.664403] Serial: 8250/16550 driver, 4 ports, IRQ sharing enabled
[ 2.664875] PNP: PS/2 Controller [PNP0303:PS2K,PNP0f13:PS2M] at 0x60,0x64 irq 1,12
[ 2.666343] serio: i8042 KBD port at 0x60,0x64 irq 1
[ 2.666354] serio: i8042 AUX port at 0x60,0x64 irq 12
[ 2.666446] mice: PS/2 mouse device common for all mice
[ 2.666502] rtc_cmos 00:06: RTC can wake from S4
[ 2.666542] rtc_cmos 00:06: rtc core: registered rtc_cmos as rtc0
[ 2.666577] rtc0: alarms up to one month, y3k, 242 bytes nvram, hpet irqs
[ 2.666590] cpuidle: using governor ladder
[ 2.666592] cpuidle: using governor menu
[ 2.666597] No iBFT detected.
[ 2.667004] TCP cubic registered
[ 2.667175] NET: Registered protocol family 10
[ 2.668039] Mobile IPv6
[ 2.668042] NET: Registered protocol family 17
[ 2.668065] Using IPI No-Shortcut mode
[ 2.668140] PM: Resume from disk failed.
[ 2.668153] registered taskstats version 1
[ 2.668708] rtc_cmos 00:06: setting system clock to 2006-07-16 12:05:17 UTC (1153051517)
[ 2.668785] Initalizing network drop monitor service
[ 2.668809] Freeing unused kernel memory: 380k freed
[ 2.669020] Write protecting the kernel text: 2508k
[ 2.669049] Write protecting the kernel read-only data: 920k
[ 2.688468] udev[56]: starting version 164
[ 2.701049] input: AT Translated Set 2 keyboard as /devices/platform/i8042/serio0/input/input0
[ 2.822212] usbcore: registered new interface driver usbfs
[ 2.822392] usbcore: registered new interface driver hub
[ 2.822571] usbcore: registered new device driver usb
[ 2.839165] SCSI subsystem initialized
[ 2.845632] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
[ 2.845668] ehci_hcd 0000:00:1d.7: PCI INT A -> GSI 23 (level, low) -> IRQ 23
[ 2.845693] ehci_hcd 0000:00:1d.7: setting latency timer to 64
[ 2.845698] ehci_hcd 0000:00:1d.7: EHCI Host Controller
[ 2.845722] ehci_hcd 0000:00:1d.7: new USB bus registered, assigned bus number 1
[ 2.845755] ehci_hcd 0000:00:1d.7: using broken periodic workaround
[ 2.845769] ehci_hcd 0000:00:1d.7: debug port 1
[ 2.849666] ehci_hcd 0000:00:1d.7: cache line size of 32 is not supported
[ 2.849688] ehci_hcd 0000:00:1d.7: irq 23, io mem 0xd0544000
[ 2.850549] e100: Intel(R) PRO/100 Network Driver, 3.5.24-k2-NAPI
[ 2.850552] e100: Copyright(c) 1999-2006 Intel Corporation
[ 2.850595] e100 0000:0a:08.0: PCI INT A -> GSI 20 (level, low) -> IRQ 20
[ 2.850661] e100 0000:0a:08.0: setting latency timer to 64
[ 2.878353] e100 0000:0a:08.0: PME# disabled
[ 2.879973] uhci_hcd: USB Universal Host Controller Interface driver
[ 2.880874] e100: eth0: e100_probe: addr 0xd0006000, irq 20, MAC addr 00:16:36:e3:9d:f3
[ 2.888181] ehci_hcd 0000:00:1d.7: USB 2.0 started, EHCI 1.00
[ 2.888212] usb usb1: New USB device found, idVendor=1d6b, idProduct=0002
[ 2.888215] usb usb1: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[ 2.888219] usb usb1: Product: EHCI Host Controller
[ 2.888222] usb usb1: Manufacturer: Linux 2.6.32-5-686 ehci_hcd
[ 2.888224] usb usb1: SerialNumber: 0000:00:1d.7
[ 2.888326] usb usb1: configuration #1 chosen from 1 choice
[ 2.888366] hub 1-0:1.0: USB hub found
[ 2.888376] hub 1-0:1.0: 8 ports detected
[ 2.888497] uhci_hcd 0000:00:1d.0: PCI INT A -> GSI 23 (level, low) -> IRQ 23
[ 2.888510] uhci_hcd 0000:00:1d.0: setting latency timer to 64
[ 2.888514] uhci_hcd 0000:00:1d.0: UHCI Host Controller
[ 2.888524] uhci_hcd 0000:00:1d.0: new USB bus registered, assigned bus number 2
[ 2.888558] uhci_hcd 0000:00:1d.0: irq 23, io base 0x00001820
[ 2.888597] usb usb2: New USB device found, idVendor=1d6b, idProduct=0001
[ 2.888600] usb usb2: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[ 2.888603] usb usb2: Product: UHCI Host Controller
[ 2.888606] usb usb2: Manufacturer: Linux 2.6.32-5-686 uhci_hcd
[ 2.888609] usb usb2: SerialNumber: 0000:00:1d.0
[ 2.888683] usb usb2: configuration #1 chosen from 1 choice
[ 2.888716] hub 2-0:1.0: USB hub found
[ 2.888724] hub 2-0:1.0: 2 ports detected
[ 2.888784] uhci_hcd 0000:00:1d.1: PCI INT B -> GSI 19 (level, low) -> IRQ 19
[ 2.888794] uhci_hcd 0000:00:1d.1: setting latency timer to 64
[ 2.888798] uhci_hcd 0000:00:1d.1: UHCI Host Controller
[ 2.888811] uhci_hcd 0000:00:1d.1: new USB bus registered, assigned bus number 3
[ 2.888852] uhci_hcd 0000:00:1d.1: irq 19, io base 0x00001840
[ 2.888890] usb usb3: New USB device found, idVendor=1d6b, idProduct=0001
[ 2.888894] usb usb3: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[ 2.888897] usb usb3: Product: UHCI Host Controller
[ 2.888899] usb usb3: Manufacturer: Linux 2.6.32-5-686 uhci_hcd
[ 2.888902] usb usb3: SerialNumber: 0000:00:1d.1
[ 2.888979] usb usb3: configuration #1 chosen from 1 choice
[ 2.889016] hub 3-0:1.0: USB hub found
[ 2.889024] hub 3-0:1.0: 2 ports detected
[ 2.889082] uhci_hcd 0000:00:1d.2: PCI INT C -> GSI 18 (level, low) -> IRQ 18
[ 2.889094] uhci_hcd 0000:00:1d.2: setting latency timer to 64
[ 2.889098] uhci_hcd 0000:00:1d.2: UHCI Host Controller
[ 2.889106] uhci_hcd 0000:00:1d.2: new USB bus registered, assigned bus number 4
[ 2.889146] uhci_hcd 0000:00:1d.2: irq 18, io base 0x00001860
[ 2.889184] usb usb4: New USB device found, idVendor=1d6b, idProduct=0001
[ 2.889187] usb usb4: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[ 2.889190] usb usb4: Product: UHCI Host Controller
[ 2.889193] usb usb4: Manufacturer: Linux 2.6.32-5-686 uhci_hcd
[ 2.889196] usb usb4: SerialNumber: 0000:00:1d.2
[ 2.889271] usb usb4: configuration #1 chosen from 1 choice
[ 2.889305] hub 4-0:1.0: USB hub found
[ 2.889313] hub 4-0:1.0: 2 ports detected
[ 2.889371] uhci_hcd 0000:00:1d.3: PCI INT D -> GSI 16 (level, low) -> IRQ 16
[ 2.889380] uhci_hcd 0000:00:1d.3: setting latency timer to 64
[ 2.889385] uhci_hcd 0000:00:1d.3: UHCI Host Controller
[ 2.889394] uhci_hcd 0000:00:1d.3: new USB bus registered, assigned bus number 5
[ 2.889432] uhci_hcd 0000:00:1d.3: irq 16, io base 0x00001880
[ 2.889473] usb usb5: New USB device found, idVendor=1d6b, idProduct=0001
[ 2.889476] usb usb5: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[ 2.889479] usb usb5: Product: UHCI Host Controller
[ 2.889482] usb usb5: Manufacturer: Linux 2.6.32-5-686 uhci_hcd
[ 2.889485] usb usb5: SerialNumber: 0000:00:1d.3
[ 2.889557] usb usb5: configuration #1 chosen from 1 choice
[ 2.889590] hub 5-0:1.0: USB hub found
[ 2.889597] hub 5-0:1.0: 2 ports detected
[ 2.889999] libata version 3.00 loaded.
[ 2.891679] firewire_ohci 0000:0a:04.1: enabling device (0000 -> 0002)
[ 2.891688] firewire_ohci 0000:0a:04.1: PCI INT A -> GSI 17 (level, low) -> IRQ 17
[ 2.891699] firewire_ohci 0000:0a:04.1: setting latency timer to 64
[ 2.894564] ata_piix 0000:00:1f.2: version 2.13
[ 2.894585] ata_piix 0000:00:1f.2: PCI INT B -> GSI 19 (level, low) -> IRQ 19
[ 2.894593] ata_piix 0000:00:1f.2: MAP [ P0 P2 IDE IDE ]
[ 2.896690] sdhci: Secure Digital Host Controller Interface driver
[ 2.896693] sdhci: Copyright(c) Pierre Ossman
[ 2.905126] thermal LNXTHERM:01: registered as thermal_zone0
[ 2.905139] ACPI: Thermal Zone [THRM] (33 C)
[ 2.961018] firewire_ohci: Added fw-ohci device 0000:0a:04.1, OHCI version 1.10
[ 2.961096] sdhci-pci 0000:0a:04.3: SDHCI controller found [104c:803c] (rev 0)
[ 2.961115] sdhci-pci 0000:0a:04.3: enabling device (0000 -> 0002)
[ 2.961125] sdhci-pci 0000:0a:04.3: PCI INT A -> GSI 17 (level, low) -> IRQ 17
[ 2.961170] sdhci-pci 0000:0a:04.3: setting latency timer to 64
[ 2.961213] Registered led device: mmc0::
[ 2.961263] mmc0: SDHCI controller on PCI [0000:0a:04.3] using DMA
[ 3.048023] ata_piix 0000:00:1f.2: setting latency timer to 64
[ 3.048121] scsi0 : ata_piix
[ 3.048232] scsi1 : ata_piix
[ 3.048394] ata1: SATA max UDMA/133 cmd 0x1f0 ctl 0x3f6 bmdma 0x18b0 irq 14
[ 3.048398] ata2: PATA max UDMA/100 cmd 0x170 ctl 0x376 bmdma 0x18b8 irq 15
[ 3.212524] ata1.00: ATA-6: TOSHIBA MK1032GSX, AS022M, max UDMA/100
[ 3.212528] ata1.00: 195371568 sectors, multi 16: LBA48 NCQ (depth 0/32)
[ 3.212875] ata2.00: ATAPI: MATSHITADVD-RAM UJ-850S, 1.10, max UDMA/33
[ 3.220573] ata1.00: configured for UDMA/100
[ 3.220693] scsi 0:0:0:0: Direct-Access ATA TOSHIBA MK1032GS AS02 PQ: 0 ANSI: 5
[ 3.228351] ata2.00: configured for UDMA/33
[ 3.230716] scsi 1:0:0:0: CD-ROM MATSHITA DVD-RAM UJ-850S 1.10 PQ: 0 ANSI: 5
[ 3.245252] sd 0:0:0:0: [sda] 195371568 512-byte logical blocks: (100 GB/93.1 GiB)
[ 3.245317] sd 0:0:0:0: [sda] Write Protect is off
[ 3.245320] sd 0:0:0:0: [sda] Mode Sense: 00 3a 00 00
[ 3.245363] sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
[ 3.245587] sda:sr0: scsi3-mmc drive: 24x/24x writer dvd-ram cd/rw xa/form2 cdda tray
[ 3.248757] Uniform CD-ROM driver Revision: 3.20
[ 3.248866] sr 1:0:0:0: Attached scsi CD-ROM sr0
[ 3.277643] sda1 sda2 < sda5 >
[ 3.312020] sd 0:0:0:0: [sda] Attached SCSI disk
[ 3.317861] sd 0:0:0:0: Attached scsi generic sg0 type 0
[ 3.319277] sr 1:0:0:0: Attached scsi generic sg1 type 5
[ 3.460098] firewire_core: created device fw0: GUID 00c09f0000e5ad42, S400
[ 3.666311] PM: Starting manual resume from disk
[ 3.666315] PM: Resume from partition 8:5
[ 3.666317] PM: Checking hibernation image.
[ 3.666509] PM: Error -22 checking image file
[ 3.666511] PM: Resume from disk failed.
[ 3.732746] kjournald starting. Commit interval 5 seconds
[ 3.732758] EXT3-fs: mounted filesystem with ordered data mode.
[ 5.375347] udev[352]: starting version 164
[ 5.834805] ACPI: WMI: Mapper loaded
[ 5.852117] ACPI: AC Adapter [ACAD] (on-line)
[ 5.945582] ACPI: SSDT 3f692e1a 00238 (v01 PmRef Cpu0Ist 00003000 INTL 20060912)
[ 5.946241] ACPI: SSDT 3f6928d1 004C4 (v01 PmRef Cpu0Cst 00003001 INTL 20060912)
[ 5.948908] Monitor-Mwait will be used to enter C-1 state
[ 5.948945] Monitor-Mwait will be used to enter C-2 state
[ 5.948980] Monitor-Mwait will be used to enter C-3 state
[ 5.948989] Marking TSC unstable due to TSC halts in idle
[ 5.949220] Switching to clocksource hpet
[ 5.949551] processor LNXCPU:00: registered as cooling_device0
[ 5.950280] ACPI: SSDT 3f693052 000C8 (v01 PmRef Cpu1Ist 00003000 INTL 20060912)
[ 5.950650] ACPI: SSDT 3f692d95 00085 (v01 PmRef Cpu1Cst 00003000 INTL 20060912)
[ 5.951820] processor LNXCPU:01: registered as cooling_device1
[ 6.072286] cfg80211: Using static regulatory domain info
[ 6.072289] cfg80211: Regulatory domain: US
[ 6.072292] (start_freq - end_freq @ bandwidth), (max_antenna_gain, max_eirp)
[ 6.072296] (2402000 KHz - 2472000 KHz @ 40000 KHz), (600 mBi, 2700 mBm)
[ 6.072299] (5170000 KHz - 5190000 KHz @ 40000 KHz), (600 mBi, 2300 mBm)
[ 6.072302] (5190000 KHz - 5210000 KHz @ 40000 KHz), (600 mBi, 2300 mBm)
[ 6.072305] (5210000 KHz - 5230000 KHz @ 40000 KHz), (600 mBi, 2300 mBm)
[ 6.072309] (5230000 KHz - 5330000 KHz @ 40000 KHz), (600 mBi, 2300 mBm)
[ 6.072312] (5735000 KHz - 5835000 KHz @ 40000 KHz), (600 mBi, 3000 mBm)
[ 6.072319] cfg80211: Calling CRDA for country: US
[ 6.083539] input: PC Speaker as /devices/platform/pcspkr/input/input1
[ 6.723121] Synaptics Touchpad, model: 1, fw: 6.2, id: 0x25a0b1, caps: 0xa04713/0x0/0x0
[ 6.723135] synaptics: Toshiba Satellite P100 detected, limiting rate to 40pps.
[ 6.757030] input: SynPS/2 Synaptics TouchPad as /devices/platform/i8042/serio1/input/input2
[ 6.829249] acpi device:03: registered as cooling_device2
[ 6.829463] input: Video Bus as /devices/LNXSYSTM:00/LNXSYBUS:00/PNP0A08:00/LNXVIDEO:00/input/input3
[ 6.829507] ACPI: Video Device [GFX0] (multi-head: yes rom: no post: no)
[ 6.980376] ACPI: Battery Slot [BAT1] (battery present)
[ 6.980530] input: Lid Switch as /devices/LNXSYSTM:00/LNXSYBUS:00/PNP0C0D:00/input/input4
[ 6.983239] tifm_7xx1 0000:0a:04.2: enabling device (0000 -> 0002)
[ 6.983250] tifm_7xx1 0000:0a:04.2: PCI INT A -> GSI 17 (level, low) -> IRQ 17
[ 6.983261] tifm_7xx1 0000:0a:04.2: setting latency timer to 64
[ 6.997954] intel_rng: FWH not detected
[ 7.013193] ACPI: Lid Switch [LID]
[ 7.013333] input: Power Button as /devices/LNXSYSTM:00/LNXSYBUS:00/PNP0C0C:00/input/input5
[ 7.013390] ACPI: Power Button [PWRB]
[ 7.013452] input: Power Button as /devices/LNXSYSTM:00/LNXPWRBN:00/input/input6
[ 7.013485] ACPI: Power Button [PWRF]
[ 7.217891] i801_smbus 0000:00:1f.3: PCI INT B -> GSI 19 (level, low) -> IRQ 19
[ 7.217899] ACPI: I/O resource 0000:00:1f.3 [0x18c0-0x18df] conflicts with ACPI region SMBI [0x18c0-0x18cf]
[ 7.217969] ACPI: If an ACPI driver is available for this device, you should use it instead of the native driver
[ 7.270768] yenta_cardbus 0000:0a:04.0: CardBus bridge found [1179:ff31]
[ 7.270796] yenta_cardbus 0000:0a:04.0: Using CSCINT to route CSC interrupts to PCI
[ 7.270799] yenta_cardbus 0000:0a:04.0: Routing CardBus interrupts to PCI
[ 7.270806] yenta_cardbus 0000:0a:04.0: TI: mfunc 0x01a21b22, devctl 0x66
[ 7.298840] iwl3945: Intel(R) PRO/Wireless 3945ABG/BG Network Connection driver for Linux, 1.2.26ks
[ 7.298844] iwl3945: Copyright(c) 2003-2009 Intel Corporation
[ 7.298923] iwl3945 0000:03:00.0: enabling device (0000 -> 0002)
[ 7.298938] iwl3945 0000:03:00.0: PCI INT A -> GSI 17 (level, low) -> IRQ 17
[ 7.298959] iwl3945 0000:03:00.0: setting latency timer to 64
[ 7.334991] [drm] Initialized drm 1.1.0 20060810
[ 7.354903] iwl3945 0000:03:00.0: Tunable channels: 13 802.11bg, 23 802.11a channels
[ 7.354906] iwl3945 0000:03:00.0: Detected Intel Wireless WiFi Link 3945ABG
[ 7.355053] iwl3945 0000:03:00.0: irq 27 for MSI/MSI-X
[ 7.392331] phy0: Selected rate control algorithm 'iwl-3945-rs'
[ 7.488565] i915 0000:00:02.0: PCI INT A -> GSI 16 (level, low) -> IRQ 16
[ 7.488572] i915 0000:00:02.0: setting latency timer to 64
[ 7.495128] [drm] set up 7M of stolen space
[ 7.502076] yenta_cardbus 0000:0a:04.0: ISA IRQ mask 0x0cf8, PCI irq 17
[ 7.502082] yenta_cardbus 0000:0a:04.0: Socket status: 30000006
[ 7.502087] pci_bus 0000:0a: Raising subordinate bus# of parent bus (#0a) from #0b to #0e
[ 7.502095] yenta_cardbus 0000:0a:04.0: pcmcia: parent PCI bridge I/O window: 0x2000 - 0x2fff
[ 7.502099] pcmcia_socket pcmcia_socket0: cs: IO port probe 0x2000-0x2fff: clean.
[ 7.502394] yenta_cardbus 0000:0a:04.0: pcmcia: parent PCI bridge Memory window: 0xd0000000 - 0xd00fffff
[ 7.502398] yenta_cardbus 0000:0a:04.0: pcmcia: parent PCI bridge Memory window: 0x40000000 - 0x43ffffff
[ 7.597363] [drm] initialized overlay support
[ 7.819254] pcmcia_socket pcmcia_socket0: cs: IO port probe 0x100-0x3af: clean.
[ 7.821569] pcmcia_socket pcmcia_socket0: cs: IO port probe 0x3e0-0x4ff: excluding 0x4d0-0x4d7
[ 7.822542] pcmcia_socket pcmcia_socket0: cs: IO port probe 0x820-0x8ff: clean.
[ 7.823344] pcmcia_socket pcmcia_socket0: cs: IO port probe 0xc00-0xcf7: clean.
[ 7.824348] pcmcia_socket pcmcia_socket0: cs: IO port probe 0xa00-0xaff: clean.
[ 8.501117] Console: switching to colour frame buffer device 180x56
[ 8.508435] fb0: inteldrmfb frame buffer device
[ 8.508437] registered panic notifier
[ 8.508446] [drm] Initialized i915 1.6.0 20080730 for 0000:00:02.0 on minor 0
[ 8.508517] HDA Intel 0000:00:1b.0: PCI INT A -> GSI 22 (level, low) -> IRQ 22
[ 8.508558] HDA Intel 0000:00:1b.0: setting latency timer to 64
[ 9.507386] Adding 2000888k swap on /dev/sda5. Priority:-1 extents:1 across:2000888k
[ 9.768124] EXT3 FS on sda1, internal journal
[ 9.949598] loop: module loaded
[ 126.904200] usb 1-3: new high speed USB device using ehci_hcd and address 2
[ 127.037305] usb 1-3: New USB device found, idVendor=0781, idProduct=5572
[ 127.037314] usb 1-3: New USB device strings: Mfr=1, Product=2, SerialNumber=3
[ 127.037321] usb 1-3: Product: Firebird USB Flash Drive
[ 127.037326] usb 1-3: Manufacturer: SanDisk
[ 127.037331] usb 1-3: SerialNumber: 4C532000051216100333
[ 127.037542] usb 1-3: configuration #1 chosen from 1 choice
[ 127.106744] Initializing USB Mass Storage driver...
[ 127.106942] scsi2 : SCSI emulation for USB Mass Storage devices
[ 127.107291] usbcore: registered new interface driver usb-storage
[ 127.107299] USB Mass Storage support registered.
[ 127.107496] usb-storage: device found at 2
[ 127.107500] usb-storage: waiting for device to settle before scanning
[ 132.104420] usb-storage: device scan complete
[ 132.105465] scsi 2:0:0:0: Direct-Access SanDisk Cruzer Switch 1.26 PQ: 0 ANSI: 5
[ 132.106708] sd 2:0:0:0: Attached scsi generic sg2 type 0
[ 132.108649] sd 2:0:0:0: [sdb] 15633408 512-byte logical blocks: (8.00 GB/7.45 GiB)
[ 132.109896] sd 2:0:0:0: [sdb] Write Protect is off
[ 132.109903] sd 2:0:0:0: [sdb] Mode Sense: 43 00 00 00
[ 132.109909] sd 2:0:0:0: [sdb] Assuming drive cache: write through
[ 132.115884] sd 2:0:0:0: [sdb] Assuming drive cache: write through
[ 132.115895] sdb: sdb1
[ 132.130642] sd 2:0:0:0: [sdb] Assuming drive cache: write through
[ 132.130652] sd 2:0:0:0: [sdb] Attached SCSI removable disk
[ 132.784197] usb 2-2: new full speed USB device using uhci_hcd and address 2
[ 132.957231] usb 2-2: New USB device found, idVendor=046d, idProduct=c526
[ 132.957240] usb 2-2: New USB device strings: Mfr=1, Product=2, SerialNumber=0
[ 132.957246] usb 2-2: Product: USB Receiver
[ 132.957251] usb 2-2: Manufacturer: Logitech
[ 132.957454] usb 2-2: configuration #1 chosen from 1 choice
[ 133.043959] usbcore: registered new interface driver hiddev
[ 133.047631] input: Logitech USB Receiver as /devices/pci0000:00/0000:00:1d.0/usb2/2-2/2-2:1.0/input/input7
[ 133.047831] generic-usb 0003:046D:C526.0001: input,hidraw0: USB HID v1.11 Mouse [Logitech USB Receiver] on usb-0000:00:1d.0-2/input0
[ 133.052488] input: Logitech USB Receiver as /devices/pci0000:00/0000:00:1d.0/usb2/2-2/2-2:1.1/input/input8
[ 133.052807] generic-usb 0003:046D:C526.0002: input,hiddev0,hidraw1: USB HID v1.11 Device [Logitech USB Receiver] on usb-0000:00:1d.0-2/input1
[ 133.052862] usbcore: registered new interface driver usbhid
[ 133.052870] usbhid: v2.6:USB HID core driverWszystko wygląda poprawnie, postaw interfejs i spróbuj jeszcze raz przeskanować sieć:
Kod: Zaznacz cały
ifup wlan0Dostaję odpowiedź:
A jak zainstalować menadżera graficznego, może tak będzie łatwiej?
Kod: Zaznacz cały
Ignoring unkown interface wlan0=wlan0https://wiki.debian.org/WiFi/HowToUse - network manager, albo wicd. Tylko, że może być potrzebne zainstalowanie więcej zależności. Sprawdź może któryś z tych pakietów jest na płycie.
A najlepiej jakbyś podłączył laptop do sieci lan przynajmniej na czas instalacji wifi.
A najlepiej jakbyś podłączył laptop do sieci lan przynajmniej na czas instalacji wifi.
Ponieważ przez kabel też nie ma sieci, mam pytanie. Po poleceniu:
dostaję szczegółowe dane odnośnie ustawienia kart sieciowych, gdzie można je zmienić?
Uruchomiłem wszystko, że pięknie działa przez LAN. Utworzyłem nawet automatyczne przełączanie sieci, jeśli kabel LAN jest wypięty tak, że jak na mnie spory sukces ale jednego nadal nie mogę okiełznać działającego WIFI.
Po poleceniu:
Po poleceniu:
Wygląda, że jest prawidłowo, jednak sieć nie działa jak tylko wyjmę kabel.
Teraz jeszcze po poleceniu:
Otrzymuję coś takiego, z czego nie wiem skąd się bierze ta druga zduplikowana karta, o innych adresach IP, a tym samym mac adresie?
Kod: Zaznacz cały
ifconfig -aUruchomiłem wszystko, że pięknie działa przez LAN. Utworzyłem nawet automatyczne przełączanie sieci, jeśli kabel LAN jest wypięty tak, że jak na mnie spory sukces ale jednego nadal nie mogę okiełznać działającego WIFI.
Po poleceniu:
Kod: Zaznacz cały
ifconfig
eth0 Link encap:Ethernet HWaddr 00:16:36:e3:9d:f3
inet addr:192.168.1.13 Bcast:192.168.1.255 Mask:255.255.255.0
inet6 addr: fe80::216:36ff:fee3:9df3/64 Scope:Link
UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1
RX packets:2638 errors:0 dropped:0 overruns:0 frame:0
TX packets:2573 errors:0 dropped:0 overruns:0 carrier:0
collisions:0 txqueuelen:1000
RX bytes:2524764 (2.4 MiB) TX bytes:376115 (367.2 KiB)
lo Link encap:Local Loopback
inet addr:127.0.0.1 Mask:255.0.0.0
inet6 addr: ::1/128 Scope:Host
UP LOOPBACK RUNNING MTU:16436 Metric:1
RX packets:26 errors:0 dropped:0 overruns:0 frame:0
TX packets:26 errors:0 dropped:0 overruns:0 carrier:0
collisions:0 txqueuelen:0
RX bytes:1982 (1.9 KiB) TX bytes:1982 (1.9 KiB)
wlan0 Link encap:Ethernet HWaddr 00:1c:bf:42:45:40
inet addr:192.168.1.14 Bcast:192.168.1.255 Mask:255.255.255.0
inet6 addr: fe80::21c:bfff:fe42:4540/64 Scope:Link
UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1
RX packets:958 errors:0 dropped:0 overruns:0 frame:0
TX packets:70 errors:0 dropped:0 overruns:0 carrier:0
collisions:0 txqueuelen:1000
RX bytes:106672 (104.1 KiB) TX bytes:10662 (10.4 KiB)
Po poleceniu:
Kod: Zaznacz cały
iwconfig
lo no wireless extensions.
eth0 no wireless extensions.
wlan0 IEEE 802.11abg ESSID:"DrayTek"
Mode:Managed Frequency:2.437 GHz Access Point: 00:1D:AA:A6:3E:00
Bit Rate=1 Mb/s Tx-Power=15 dBm
Retry long limit:7 RTS thr :o ff Fragment thr :o ff
Encryption key :o ff
Power Management :o ff
Link Quality=55/70 Signal level=-55 dBm
Rx invalid nwid:0 Rx invalid crypt:0 Rx invalid frag:0
Tx excessive retries:0 Invalid misc:0 Missed beacon:0
pan0 no wireless extensions.
Wygląda, że jest prawidłowo, jednak sieć nie działa jak tylko wyjmę kabel.
Teraz jeszcze po poleceniu:
Kod: Zaznacz cały
root@debian:~# ifconfig -a
eth0 Link encap:Ethernet HWaddr 00:16:36:e3:9d:f3
inet addr:192.168.1.13 Bcast:192.168.1.255 Mask:255.255.255.0
inet6 addr: fe80::216:36ff:fee3:9df3/64 Scope:Link
UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1
RX packets:5147 errors:0 dropped:0 overruns:0 frame:0
TX packets:5267 errors:0 dropped:0 overruns:0 carrier:0
collisions:0 txqueuelen:1000
RX bytes:3912091 (3.7 MiB) TX bytes:817742 (798.5 KiB)
lo Link encap:Local Loopback
inet addr:127.0.0.1 Mask:255.0.0.0
inet6 addr: ::1/128 Scope:Host
UP LOOPBACK RUNNING MTU:16436 Metric:1
RX packets:266 errors:0 dropped:0 overruns:0 frame:0
TX packets:266 errors:0 dropped:0 overruns:0 carrier:0
collisions:0 txqueuelen:0
RX bytes:20196 (19.7 KiB) TX bytes:20196 (19.7 KiB)
pan0 Link encap:Ethernet HWaddr 52:11:f3:28:4d:73
BROADCAST MULTICAST MTU:1500 Metric:1
RX packets:0 errors:0 dropped:0 overruns:0 frame:0
TX packets:0 errors:0 dropped:0 overruns:0 carrier:0
collisions:0 txqueuelen:0
RX bytes:0 (0.0 B) TX bytes:0 (0.0 B)
wlan0 Link encap:Ethernet HWaddr 00:1c:bf:42:45:40
inet6 addr: fe80::21c:bfff:fe42:4540/64 Scope:Link
UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1
RX packets:758 errors:0 dropped:0 overruns:0 frame:0
TX packets:212 errors:0 dropped:0 overruns:0 carrier:0
collisions:0 txqueuelen:1000
RX bytes:127565 (124.5 KiB) TX bytes:40934 (39.9 KiB)
wlan0:avahi Link encap:Ethernet HWaddr 00:1c:bf:42:45:40
inet addr:169.254.5.181 Bcast:169.254.255.255 Mask:255.255.0.0
UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1
Jako root:
i zmień wpisy na:
Kod: Zaznacz cały
vim /etc/default/avahi-daemonKod: Zaznacz cały
AVAHI_DAEMON_START=0
AVAHI_DAEMON_DETECT_LOCAL=1
Nic się nie zmienia. Nadal to samo.
Ciekawi mnie jednak jedno, dlaczego po poleceniu
widzę inny mac adres karty sieciowej wifi niż po poleceniu:
Ja nie mam włączonego DHCP, muszę bindować adresy MAC do adresów IP urządzeń, bo taki był zamiar jak konfigurowałem sieć. Więc żeby przypisać mac adres do numeru IP i przepuścić ruch do urządzenia muszę znać poprawny mac adres urządzenia. Co wydaje się być nieco trudne w tej sytuacji.
Obecnie przypisałem adres 192.168.1.14 do adresu 00:1c:bf:42:45:40 ale pojawił się też adres :00:1D:AA:A6:3E:00 i tutaj już zgłupiałem.
Karta sieciowa o mac adresie 00:16:36:e3:9d:f3 ma przypisany adres IP 192.168.1.13 i dobrze działa.
Kolejna rzecz, to reakcja na sprawdzenie, czy sieć działa poprawnie?
Ciekawi mnie jednak jedno, dlaczego po poleceniu
Kod: Zaznacz cały
ifconfigKod: Zaznacz cały
iwconfigObecnie przypisałem adres 192.168.1.14 do adresu 00:1c:bf:42:45:40 ale pojawił się też adres :00:1D:AA:A6:3E:00 i tutaj już zgłupiałem.
Karta sieciowa o mac adresie 00:16:36:e3:9d:f3 ma przypisany adres IP 192.168.1.13 i dobrze działa.
Kod: Zaznacz cały
root@debian:~# iwconfig
lo no wireless extensions.
eth0 no wireless extensions.
wlan0 IEEE 802.11abg ESSID:"DrayTek"
Mode:Managed Frequency:2.437 GHz Access Point: 00:1D:AA:A6:3E:00 [color=#ff0000]<<<<<<<<---------------------[/color]
Bit Rate=54 Mb/s Tx-Power=15 dBm
Retry long limit:7 RTS thr :o ff Fragment thr :o ff
Encryption key :o ff
Power Management :o ff
Link Quality=52/70 Signal level=-58 dBm
Rx invalid nwid:0 Rx invalid crypt:0 Rx invalid frag:0
Tx excessive retries:0 Invalid misc:0 Missed beacon:0
pan0 no wireless extensions.Kod: Zaznacz cały
root@debian:~# ifconfig
eth0 Link encap:Ethernet HWaddr 00:16:36:e3:9d:f3
inet6 addr: fe80::216:36ff:fee3:9df3/64 Scope:Link
UP BROADCAST MULTICAST MTU:1500 Metric:1
RX packets:3770 errors:0 dropped:0 overruns:0 frame:0
TX packets:3024 errors:0 dropped:0 overruns:0 carrier:0
collisions:0 txqueuelen:1000
RX bytes:2449126 (2.3 MiB) TX bytes:749061 (731.5 KiB)
lo Link encap:Local Loopback
inet addr:127.0.0.1 Mask:255.0.0.0
inet6 addr: ::1/128 Scope:Host
UP LOOPBACK RUNNING MTU:16436 Metric:1
RX packets:56 errors:0 dropped:0 overruns:0 frame:0
TX packets:56 errors:0 dropped:0 overruns:0 carrier:0
collisions:0 txqueuelen:0
RX bytes:4372 (4.2 KiB) TX bytes:4372 (4.2 KiB)
wlan0 Link encap:Ethernet HWaddr 00:1c:bf:42:45:40 [color=#ff0000] <<<<<------------------ [/color]
inet addr:192.168.1.14 Bcast:192.168.1.255 Mask:255.255.255.0
inet6 addr: fe80::21c:bfff:fe42:4540/64 Scope:Link
UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1
RX packets:1021 errors:0 dropped:0 overruns:0 frame:0
TX packets:1038 errors:0 dropped:0 overruns:0 carrier:0
collisions:0 txqueuelen:1000
RX bytes:232895 (227.4 KiB) TX bytes:130714 (127.6 KiB)
Kolejna rzecz, to reakcja na sprawdzenie, czy sieć działa poprawnie?
Kod: Zaznacz cały
root@debian:~# iwconfig wlan0 essid TwójDrayTek key XXXXXXXXXXXXX
Error for wireless request "Set Encode" (8B2A) :
invalid argument "XXXXXXXXXXXXX"Mac adres w wyniku polecenia:
jest adresem sprzętowym punktu dostępowego (interfejs bezprzewodowy rutera) nie twojego interfejsu.
Jakiego rodzaju szyfrowania używa twoja sieć bezprzewodowa, ponieważ wydaje mi się, że to polecenie
oczekuje klucza WEP?
Próbowałeś skonfigurować sieć bezprzewodową z poziomu NetworkManagera, jaki rezultat?
Kod: Zaznacz cały
iwconfgJakiego rodzaju szyfrowania używa twoja sieć bezprzewodowa, ponieważ wydaje mi się, że to polecenie
Kod: Zaznacz cały
root@debian:~# iwconfig wlan0 essid TwójDrayTek key XXXXXXXXXXXXXPróbowałeś skonfigurować sieć bezprzewodową z poziomu NetworkManagera, jaki rezultat?