Sie

[nahkranoth]

Witam.
Sieć wygląda następująco: modem dialnetu połączony z ruterem pentagram cerberus, a ten z kolei kablem do stacjonarnego komputera z Windows XP i Kubuntu na pokładzie.
Na tym komuterze wszystko działa. Drugi komputer laptop powinien łączyć się bezprzewodowo. I na Windows XP wszystko działa.
Drugi system to Debian i tu zaczyna się kłopot bo nie wiem kompletnie jak się połączyć z siecią. Przeglądam z pomocą Google ale nigdzie nie mogę znaleźć jakiejś prostej komendy, która by łączyła z siecią. Przewodowo wystarczy wpisać

Kod: Zaznacz cały

dhclient

Garść informacji: karta sieciowa pcmcia tp-link tl-wn610g, Debian 5.0 Squeeze/Sid.
Zapomniałem dopisać że sieć jest zabezpieczona kluczem wep.

[Ister]

Czy karta jest w ogóle wykrywa pod Debianem? Co zwraca

Kod: Zaznacz cały

lspci

Co zwraca:

Kod: Zaznacz cały

dmesg

w temacie wi-fi?

Dalej - jak wygląda Twój plik:

Kod: Zaznacz cały

/etc/network/interfaces

Co zwracają komendy:

Kod: Zaznacz cały

ifconfig

i:

Kod: Zaznacz cały

iwconfig

podane same oraz z parametrem -a

To tak na sam duży początek.

[nahkranoth]

polecenie: lspci

Kod: Zaznacz cały

00:00.0 Host bridge: Intel Corporation 82845 845 [Brookdale] Chipset Host Bridge (rev 04)
00:01.0 PCI bridge: Intel Corporation 82845 845 [Brookdale] Chipset AGP Bridge (rev 04)
00:1e.0 PCI bridge: Intel Corporation 82801 Mobile PCI Bridge (rev 42)
00:1f.0 ISA bridge: Intel Corporation 82801CAM ISA Bridge (LPC) (rev 02)
00:1f.1 IDE interface: Intel Corporation 82801CAM IDE U100 Controller (rev 02)
00:1f.5 Multimedia audio controller: Intel Corporation 82801CA/CAM AC'97 Audio Controller (rev 02)
01:00.0 VGA compatible controller: ATI Technologies Inc Radeon Mobility M7 LW [Radeon Mobility 7500]
02:04.0 Communication controller: Agere Systems LT WinModem (rev 02)
02:06.0 CardBus bridge: Texas Instruments PCI1420 PC card Cardbus Controller
02:06.1 CardBus bridge: Texas Instruments PCI1420 PC card Cardbus Controller
02:08.0 Ethernet controller: Intel Corporation 82801CAM (ICH3) PRO/100 VM (KM) Ethernet Controller (rev 42)
02:0e.0 USB Controller: NEC Corporation USB (rev 41)
02:0e.1 USB Controller: NEC Corporation USB (rev 41)
02:0e.2 USB Controller: NEC Corporation USB 2.0 (rev 02)
03:00.0 Ethernet controller: Atheros Communications Inc. Atheros AR5001X+ Wireless Network Adapter (rev 01)

dalej dmesg ale nie bardzo rozumiem o co chodzi... wstawiam całość:

Kod: Zaznacz cały

[    0.000000] Initializing cgroup subsys cpuset
[    0.000000] Initializing cgroup subsys cpu
[    0.000000] Linux version 2.6.26-2-686 (Debian 2.6.26-15lenny3) (dannf@debian.org) (gcc version 4.1.3 20080704 (prerelease) (Debian 4.1.2-25)) #1 SMP Thu May 28 15:39:35 UTC 2009
[    0.000000] BIOS-provided physical RAM map:
[    0.000000]  BIOS-e820: 0000000000000000 - 000000000009fc00 (usable)
[    0.000000]  BIOS-e820: 000000000009fc00 - 00000000000a0000 (reserved)
[    0.000000]  BIOS-e820: 00000000000e0000 - 0000000000100000 (reserved)
[    0.000000]  BIOS-e820: 0000000000100000 - 000000001ffd0000 (usable)
[    0.000000]  BIOS-e820: 000000001ffd0000 - 000000001fff0c00 (reserved)
[    0.000000]  BIOS-e820: 000000001fff0c00 - 000000001fffc000 (ACPI NVS)
[    0.000000]  BIOS-e820: 000000001fffc000 - 0000000020000000 (reserved)
[    0.000000] 0MB HIGHMEM available.
[    0.000000] 511MB LOWMEM available.
[    0.000000] Entering add_active_range(0, 0, 131024) 0 entries of 256 used
[    0.000000] Zone PFN ranges:
[    0.000000]   DMA             0 ->     4096
[    0.000000]   Normal       4096 ->   131024
[    0.000000]   HighMem    131024 ->   131024
[    0.000000] Movable zone start PFN for each node
[    0.000000] early_node_map[1] active PFN ranges
[    0.000000]     0:        0 ->   131024
[    0.000000] On node 0 totalpages: 131024
[    0.000000]   DMA zone: 32 pages used for memmap
[    0.000000]   DMA zone: 0 pages reserved
[    0.000000]   DMA zone: 4064 pages, LIFO batch:0
[    0.000000]   Normal zone: 992 pages used for memmap
[    0.000000]   Normal zone: 125936 pages, LIFO batch:31
[    0.000000]   HighMem zone: 0 pages used for memmap
[    0.000000]   Movable zone: 0 pages used for memmap
[    0.000000] DMI 2.3 present.
[    0.000000] ACPI: RSDP 000F6A80, 0014 (r0 COMPAQ)
[    0.000000] ACPI: RSDT 1FFF0C84, 002C (r1 COMPAQ CPQ00B7  27050420 CPQ         1)
[    0.000000] ACPI: FACP 1FFF0C00, 0084 (r2 COMPAQ CPQ00B7         2 CPQ         1)
[    0.000000] ACPI: DSDT 1FFF0CB0, 6DBC (r1 COMPAQ EVON610C    10000 MSFT  100000E)
[    0.000000] ACPI: FACS 1FFFBE80, 0040
[    0.000000] ACPI: SSDT 1FFF7A6C, 010E (r1 COMPAQ  CPQGysr     1001 MSFT  100000E)
[    0.000000] ACPI: PM-Timer IO Port: 0x1008
[    0.000000] Allocating PCI resources starting at 30000000 (gap: 20000000:e0000000)
[    0.000000] PM: Registered nosave memory: 000000000009f000 - 00000000000a0000
[    0.000000] PM: Registered nosave memory: 00000000000a0000 - 00000000000e0000
[    0.000000] PM: Registered nosave memory: 00000000000e0000 - 0000000000100000
[    0.000000] SMP: Allowing 0 CPUs, 0 hotplug CPUs
[    0.000000] PERCPU: Allocating 37960 bytes of per cpu data
[    0.000000] NR_CPUS: 8, nr_cpu_ids: 1
[    0.000000] Built 1 zonelists in Zone order, mobility grouping on.  Total pages: 130000
[    0.000000] Kernel command line: root=/dev/hda7 ro quiet
[    0.000000] Local APIC disabled by BIOS -- you can enable it with "lapic"
[    0.000000] mapped APIC to ffffb000 (0140d000)
[    0.000000] Enabling fast FPU save and restore... done.
[    0.000000] Enabling unmasked SIMD FPU exception support... done.
[    0.000000] Initializing CPU#0
[    0.000000] PID hash table entries: 2048 (order: 11, 8192 bytes)
[    0.000000] Detected 1993.585 MHz processor.
[    0.004000] Console: colour VGA+ 80x25
[    0.004000] console [tty0] enabled
[    0.004000] Dentry cache hash table entries: 65536 (order: 6, 262144 bytes)
[    0.004000] Inode-cache hash table entries: 32768 (order: 5, 131072 bytes)
[    0.004000] Memory: 507972k/524096k available (1769k kernel code, 15516k reserved, 752k data, 244k init, 0k highmem)
[    0.004000] virtual kernel memory layout:
[    0.004000]     fixmap  : 0xfff4c000 - 0xfffff000   ( 716 kB)
[    0.004000]     pkmap   : 0xff800000 - 0xffc00000   (4096 kB)
[    0.004000]     vmalloc : 0xe0800000 - 0xff7fe000   ( 495 MB)
[    0.004000]     lowmem  : 0xc0000000 - 0xdffd0000   ( 511 MB)
[    0.004000]       .init : 0xc037f000 - 0xc03bc000   ( 244 kB)
[    0.004000]       .data : 0xc02ba5eb - 0xc0376620   ( 752 kB)
[    0.004000]       .text : 0xc0100000 - 0xc02ba5eb   (1769 kB)
[    0.004000] Checking if this processor honours the WP bit even in supervisor mode...Ok.
[    0.004000] CPA: page pool initialized 1 of 1 pages preallocated
[    0.084134] Calibrating delay using timer specific routine.. 3992.48 BogoMIPS (lpj=7984968)
[    0.084188] Security Framework initialized
[    0.084195] SELinux:  Disabled at boot.
[    0.084201] Capability LSM initialized
[    0.084224] Mount-cache hash table entries: 512
[    0.084441] Initializing cgroup subsys ns
[    0.084448] Initializing cgroup subsys cpuacct
[    0.084452] Initializing cgroup subsys devices
[    0.084481] CPU: Trace cache: 12K uops, L1 D cache: 8K
[    0.084486] CPU: L2 cache: 512K
[    0.084489] CPU: Hyper-Threading is disabled
[    0.084494] Intel machine check architecture supported.
[    0.084502] Intel machine check reporting enabled on CPU#0.
[    0.084506] CPU0: Intel P4/Xeon Extended MCE MSRs (12) available
[    0.084512] CPU0: Thermal monitoring enabled
[    0.084534] Checking 'hlt' instruction... OK.
[    0.100520] SMP alternatives: switching to UP code
[    0.112511] Freeing SMP alternatives: 16k freed
[    0.112519] ACPI: Core revision 20080321
[    0.128710] ACPI: setting ELCR to 0200 (from 0c00)
[    0.136008] weird, boot CPU (#0) not listedby the BIOS.
[    0.136008] SMP motherboard not detected.
[    0.136008] Local APIC not detected. Using dummy APIC emulation.
[    0.136008] SMP disabled
[    0.136008] Brought up 1 CPUs
[    0.136008] Total of 1 processors activated (3992.48 BogoMIPS).
[    0.136008] CPU0 attaching sched-domain:
[    0.136008]  domain 0: span 0
[    0.136008]   groups: 0
[    0.136008] net_namespace: 660 bytes
[    0.136008] Booting paravirtualized kernel on bare hardware
[    0.136008] NET: Registered protocol family 16
[    0.136161] ACPI: bus type pci registered
[    0.138188] PCI: PCI BIOS revision 2.10 entry at 0xf03a2, last bus=4
[    0.138192] PCI: Using configuration type 1 for base access
[    0.138206] Setting up standard PCI resources
[    0.140498] ACPI: EC: Look up EC in DSDT
[    0.160859] ACPI: Interpreter enabled
[    0.160866] ACPI: (supports S0 S3 S4 S5)
[    0.160887] ACPI: Using PIC for interrupt routing
[    0.177581] ACPI: PCI Root Bridge [C045] (0000:00)
[    0.177875] pci 0000:00:1f.0: quirk: region 1000-107f claimed by ICH4 ACPI/GPIO/TCO
[    0.177882] pci 0000:00:1f.0: quirk: region 1100-113f claimed by ICH4 GPIO
[    0.178622] PCI: Transparent bridge - 0000:00:1e.0
[    0.178691] ACPI: PCI Interrupt Routing Table [\_SB_.C045._PRT]
[    0.178729] ACPI: PCI Interrupt Routing Table [\_SB_.C045.C046._PRT]
[    0.178754] ACPI: PCI Interrupt Routing Table [\_SB_.C045.C058._PRT]
[    0.187129] ACPI: PCI Interrupt Link [C0C0] (IRQs 5 10 *11)
[    0.187424] ACPI: PCI Interrupt Link [C0C1] (IRQs 5 10 *11)
[    0.187704] ACPI: PCI Interrupt Link [C0C2] (IRQs 5 10 11) *0, disabled.
[    0.187995] ACPI: PCI Interrupt Link [C0C3] (IRQs 5 10 *11)
[    0.188362] ACPI: PCI Interrupt Link [C0C4] (IRQs 5 *10 11)
[    0.188493] ACPI: Blank IRQ resource
[    0.188496] ACPI: Resource is not an IRQ entry
[    0.188682] ACPI: PCI Interrupt Link [C0C5] (IRQs) *0, disabled.
[    0.188812] ACPI: Blank IRQ resource
[    0.188815] ACPI: Resource is not an IRQ entry
[    0.188996] ACPI: PCI Interrupt Link [C0C6] (IRQs) *0, disabled.
[    0.189126] ACPI: Blank IRQ resource
[    0.189129] ACPI: Resource is not an IRQ entry
[    0.189309] ACPI: PCI Interrupt Link [C0C7] (IRQs) *0, disabled.
[    0.189746] ACPI: Power Resource [C15D] (on)
[    0.189875] ACPI: Power Resource [C171] (on)
[    0.190001] ACPI: Power Resource [C175] (on)
[    0.190129] ACPI: Power Resource [C178] (on)
[    0.190189] ACPI: Power Resource [C181] (on)
[    0.190327] ACPI: Power Resource [C1FC] (off)
[    0.190441] ACPI: Power Resource [C1FD] (off)
[    0.190554] ACPI: Power Resource [C1FE] (off)
[    0.190668] ACPI: Power Resource [C1FF] (off)
[    0.190784] ACPI: Power Resource [C200] (off)
[    0.190897] Linux Plug and Play Support v0.97 (c) Adam Belay
[    0.190946] pnp: PnP ACPI init
[    0.190960] ACPI: bus type pnp registered
[    0.211919] pnp: PnP ACPI: found 14 devices
[    0.211924] ACPI: ACPI bus type pnp unregistered
[    0.211930] PnPBIOS: Disabled by ACPI PNP
[    0.212380] PCI: Using ACPI for IRQ routing
[    0.212666] ACPI: RTC can wake from S4
[    0.212708] system 00:00: iomem range 0x0-0x9ffff could not be reserved
[    0.212713] system 00:00: iomem range 0xe0000-0xfffff could not be reserved
[    0.212717] system 00:00: iomem range 0x100000-0x1fffffff could not be reserved
[    0.212735] system 00:0c: ioport range 0x140-0x14f has been reserved
[    0.212740] system 00:0c: iomem range 0xffb00000-0xffbfffff has been reserved
[    0.212744] system 00:0c: iomem range 0xfff00000-0xffffffff has been reserved
[    0.212752] system 00:0d: ioport range 0x4d0-0x4d1 has been reserved
[    0.212756] system 00:0d: ioport range 0x1000-0x107f has been reserved
[    0.212760] system 00:0d: ioport range 0x1100-0x113f has been reserved
[    0.212764] system 00:0d: ioport range 0x1200-0x121f has been reserved
[    0.212770] system 00:0d: iomem range 0xffc00000-0xffc003ff has been reserved
[    0.243382] PCI: region 0000:02:06.0/9 too large: 0x0000000000000000-0x0000000003ffffff
[    0.243387] PCI: region 0000:02:06.1/9 too large: 0x0000000000000000-0x0000000003ffffff
[    0.243401] PCI: Bridge: 0000:00:01.0
[    0.243405]   IO window: 3000-3fff
[    0.243410]   MEM window: 0x40400000-0x404fffff
[    0.243415]   PREFETCH window: 0x0000000048000000-0x000000004fffffff
[    0.243429] PCI: Bus 3, cardbus bridge: 0000:02:06.0
[    0.243432]   IO window: 0x00002800-0x000028ff
[    0.243437]   IO window: 0x00002c00-0x00002cff
[    0.243442]   MEM window: 0x34000000-0x37ffffff
[    0.243448] PCI: Bus 4, cardbus bridge: 0000:02:06.1
[    0.243451]   IO window: 0x00001400-0x000014ff
[    0.243456]   IO window: 0x00001800-0x000018ff
[    0.243461]   MEM window: 0x38000000-0x3bffffff
[    0.243467] PCI: Bridge: 0000:00:1e.0
[    0.243471]   IO window: 2000-2fff
[    0.243478]   MEM window: 0x40000000-0x403fffff
[    0.243483]   PREFETCH window: disabled.
[    0.243506] PCI: Setting latency timer of device 0000:00:1e.0 to 64
[    0.243994] ACPI: PCI Interrupt Link [C0C3] enabled at IRQ 11
[    0.243999] PCI: setting IRQ 11 as level-triggered
[    0.244004] ACPI: PCI Interrupt 0000:02:06.0[A] -> Link [C0C3] -> GSI 11 (level, low) -> IRQ 11
[    0.244041] ACPI: PCI Interrupt 0000:02:06.1[A] -> Link [C0C3] -> GSI 11 (level, low) -> IRQ 11
[    0.244086] NET: Registered protocol family 2
[    0.244250] IP route cache hash table entries: 4096 (order: 2, 16384 bytes)
[    0.244558] TCP established hash table entries: 16384 (order: 5, 131072 bytes)
[    0.244671] TCP bind hash table entries: 16384 (order: 5, 131072 bytes)
[    0.244779] TCP: Hash tables configured (established 16384 bind 16384)
[    0.244784] TCP reno registered
[    0.244898] NET: Registered protocol family 1
[    0.245081] checking if image is initramfs... it is
[    0.744055] Switched to high resolution mode on CPU 0
[    1.170568] Freeing initrd memory: 7710k freed
[    1.171466] audit: initializing netlink socket (disabled)
[    1.171494] type=2000 audit(1250947474.168:1): initialized
[    1.171672] Total HugeTLB memory allocated, 0
[    1.171778] VFS: Disk quotas dquot_6.5.1
[    1.171818] Dquot-cache hash table entries: 1024 (order 0, 4096 bytes)
[    1.171875] msgmni has been set to 1007
[    1.172081] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 253)
[    1.172087] io scheduler noop registered
[    1.172090] io scheduler anticipatory registered
[    1.172092] io scheduler deadline registered
[    1.172107] io scheduler cfq registered (default)
[    1.172137] pci 0000:01:00.0: Boot video device
[    1.172168] pci 0000:02:08.0: Firmware left e100 interrupts enabled; disabling
[    1.172711] isapnp: Scanning for PnP cards...
[    1.526398] isapnp: No Plug & Play device found
[    1.530292] Serial: 8250/16550 driver $Revision: 1.90 $ 4 ports, IRQ sharing enabled
[    1.530448] serial8250: ttyS0 at I/O 0x3f8 (irq = 4) is a 16550A
[    1.530652] serial8250: ttyS2 at I/O 0x3e8 (irq = 4) is a 16550A
[    1.531029] 00:02: ttyS0 at I/O 0x3f8 (irq = 4) is a 16550A
[    1.533986] brd: module loaded
[    1.534136] PNP: PS/2 Controller [PNP0303:C17E,PNP0f13:C17F] at 0x60,0x64 irq 1,12
[    1.535794] i8042.c: Detected active multiplexing controller, rev 1.1.
[    1.536537] serio: i8042 KBD port at 0x60,0x64 irq 1
[    1.536546] serio: i8042 AUX0 port at 0x60,0x64 irq 12
[    1.536551] serio: i8042 AUX1 port at 0x60,0x64 irq 12
[    1.536554] serio: i8042 AUX2 port at 0x60,0x64 irq 12
[    1.536558] serio: i8042 AUX3 port at 0x60,0x64 irq 12
[    1.536781] mice: PS/2 mouse device common for all mice
[    1.537072] rtc_cmos 00:09: rtc core: registered rtc_cmos as rtc0
[    1.537090] rtc0: alarms up to one month, y3k
[    1.537139] cpuidle: using governor ladder
[    1.537143] cpuidle: using governor menu
[    1.537150] No iBFT detected.
[    1.537814] TCP cubic registered
[    1.537819] NET: Registered protocol family 17
[    1.537830] Using IPI No-Shortcut mode
[    1.538010] registered taskstats version 1
[    1.538202] rtc_cmos 00:09: setting system clock to 2009-08-22 13:24:34 UTC (1250947474)
[    1.538573] Freeing unused kernel memory: 244k freed
[    1.571755] input: AT Translated Set 2 keyboard as /class/input/input0
[    1.707506] ACPI: Transitioning device [C201] to D3
[    1.707594] ACPI: PNP0C0B:00 is registered as cooling_device0
[    1.707603] ACPI: Fan [C201] (off)
[    1.707826] ACPI: Transitioning device [C202] to D3
[    1.707888] ACPI: PNP0C0B:01 is registered as cooling_device1
[    1.707896] ACPI: Fan [C202] (off)
[    1.708193] ACPI: Transitioning device [C203] to D3
[    1.708261] ACPI: PNP0C0B:02 is registered as cooling_device2
[    1.708270] ACPI: Fan [C203] (off)
[    1.708491] ACPI: Transitioning device [C204] to D3
[    1.708550] ACPI: PNP0C0B:03 is registered as cooling_device3
[    1.708558] ACPI: Fan [C204] (off)
[    1.708778] ACPI: Transitioning device [C205] to D3
[    1.708838] ACPI: PNP0C0B:04 is registered as cooling_device4
[    1.708846] ACPI: Fan [C205] (off)
[    1.714897] ACPI: CPU0 (power states: C1[C1] C2[C2] C3[C3])
[    1.714970] ACPI: ACPI0007:00 is registered as cooling_device5
[    1.714976] ACPI: Processor [C000] (supports 8 throttling states)
[    1.723158] ACPI: LNXTHERM:01 is registered as thermal_zone0
[    1.728716] ACPI: Thermal Zone [TZ1] (57 C)
[    1.729603] ACPI: LNXTHERM:02 is registered as thermal_zone1
[    1.729952] ACPI: Thermal Zone [C1FA] (45 C)
[    1.731328] ACPI: LNXTHERM:03 is registered as thermal_zone2
[    1.731641] ACPI: Thermal Zone [C1FB] (16 C)
[    2.048224] Linux agpgart interface v0.103
[    2.050321] agpgart: Detected an Intel 845G Chipset.
[    2.064941] agpgart: AGP aperture is 256M @ 0x60000000
[    2.189762] e100: Intel(R) PRO/100 Network Driver, 3.5.23-k4-NAPI
[    2.189768] e100: Copyright(c) 1999-2006 Intel Corporation
[    2.190325] ACPI: PCI Interrupt Link [C0C4] enabled at IRQ 10
[    2.190330] PCI: setting IRQ 10 as level-triggered
[    2.190335] ACPI: PCI Interrupt 0000:02:08.0[A] -> Link [C0C4] -> GSI 10 (level, low) -> IRQ 10
[    2.283682] e100: eth0: e100_probe: addr 0x40100000, irq 10, MAC addr 00:08:02:d8:b4:a2
[    2.299645] usbcore: registered new interface driver usbfs
[    2.299689] usbcore: registered new interface driver hub
[    2.299739] usbcore: registered new device driver usb
[    2.308599] ACPI: PCI Interrupt 0000:02:0e.2[C] -> Link [C0C4] -> GSI 10 (level, low) -> IRQ 10
[    2.308623] ehci_hcd 0000:02:0e.2: EHCI Host Controller
[    2.308828] ehci_hcd 0000:02:0e.2: new USB bus registered, assigned bus number 1
[    2.328810] Uniform Multi-Platform E-IDE driver
[    2.328820] ide: Assuming 33MHz system bus speed for PIO modes; override with idebus=xx
[    2.332124] ehci_hcd 0000:02:0e.2: irq 10, io mem 0x40300000
[    2.344061] ehci_hcd 0000:02:0e.2: USB 2.0 started, EHCI 0.95, driver 10 Dec 2004
[    2.344193] usb usb1: configuration #1 chosen from 1 choice
[    2.344240] hub 1-0:1.0: USB hub found
[    2.344253] hub 1-0:1.0: 5 ports detected
[    2.433861] Marking TSC unstable due to: TSC halts in idle.
[    2.448246] usb usb1: New USB device found, idVendor=1d6b, idProduct=0002
[    2.448251] usb usb1: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[    2.448255] usb usb1: Product: EHCI Host Controller
[    2.448258] usb usb1: Manufacturer: Linux 2.6.26-2-686 ehci_hcd
[    2.448261] usb usb1: SerialNumber: 0000:02:0e.2
[    2.448331] ICH3M: IDE controller (0x8086:0x248a rev 0x02) at  PCI slot 0000:00:1f.1
[    2.448343] PIIX_IDE 0000:00:1f.1: enabling device (0005 -> 0007)
[    2.448845] ACPI: PCI Interrupt Link [C0C2] enabled at IRQ 11
[    2.448850] ACPI: PCI Interrupt 0000:00:1f.1[A] -> Link [C0C2] -> GSI 11 (level, low) -> IRQ 11
[    2.448865] ICH3M: not 100% native mode: will probe irqs later
[    2.448881]     ide0: BM-DMA at 0x4440-0x4447
[    2.448894]     ide1: BM-DMA at 0x4448-0x444f
[    2.448901] Probing IDE interface ide0...
[    2.461808] ohci_hcd: 2006 August 04 USB 1.1 'Open' Host Controller (OHCI) Driver
[    2.736298] hda: HTS541040G9AT00, ATA DISK drive
[    2.740115] Clocksource tsc unstable (delta = -262457478 ns)
[    3.408195] hda: host max PIO4 wanted PIO255(auto-tune) selected PIO4
[    3.408446] hda: UDMA/100 mode selected
[    3.408691] Probing IDE interface ide1...
[    4.144301] hdc: MATSHITADVD-RAM UJ-841S, ATAPI CD/DVD-ROM drive
[    4.480169] hdc: host max PIO4 wanted PIO255(auto-tune) selected PIO4
[    4.480468] hdc: UDMA/33 mode selected
[    4.480884] ide0 at 0x1f0-0x1f7,0x3f6 on irq 14
[    4.497437] ide1 at 0x170-0x177,0x376 on irq 15
[    4.499236] ACPI: PCI Interrupt 0000:02:0e.0[A] -> Link [C0C4] -> GSI 10 (level, low) -> IRQ 10
[    4.499236] ohci_hcd 0000:02:0e.0: OHCI Host Controller
[    4.499236] ohci_hcd 0000:02:0e.0: new USB bus registered, assigned bus number 2
[    4.499236] ohci_hcd 0000:02:0e.0: irq 10, io mem 0x40180000
[    4.499236] No dock devices found.
[    4.515499] SCSI subsystem initialized
[    4.530702] libata version 3.00 loaded.
[    5.062946] usb usb2: configuration #1 chosen from 1 choice
[    5.062992] hub 2-0:1.0: USB hub found
[    5.063009] hub 2-0:1.0: 3 ports detected
[    5.576196] usb usb2: New USB device found, idVendor=1d6b, idProduct=0001
[    5.576202] usb usb2: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[    5.576205] usb usb2: Product: OHCI Host Controller
[    5.576209] usb usb2: Manufacturer: Linux 2.6.26-2-686 ohci_hcd
[    5.576212] usb usb2: SerialNumber: 0000:02:0e.0
[    5.576530] ACPI: PCI Interrupt 0000:02:0e.1[B] -> Link [C0C4] -> GSI 10 (level, low) -> IRQ 10
[    5.576557] ohci_hcd 0000:02:0e.1: OHCI Host Controller
[    5.576604] ohci_hcd 0000:02:0e.1: new USB bus registered, assigned bus number 3
[    5.576624] ohci_hcd 0000:02:0e.1: irq 10, io mem 0x40200000
[    6.138822] usb usb3: configuration #1 chosen from 1 choice
[    6.138865] hub 3-0:1.0: USB hub found
[    6.138881] hub 3-0:1.0: 2 ports detected
[    6.376043] usb 2-1: new low speed USB device using ohci_hcd and address 2
[    6.587783] usb 2-1: configuration #1 chosen from 1 choice
[    6.590430] usb 2-1: New USB device found, idVendor=04f3, idProduct=0210
[    6.590430] usb 2-1: New USB device strings: Mfr=0, Product=2, SerialNumber=0
[    6.590430] usb 2-1: Product: PS/2+USB Mouse
[    6.652172] usb usb3: New USB device found, idVendor=1d6b, idProduct=0001
[    6.652177] usb usb3: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[    6.652181] usb usb3: Product: OHCI Host Controller
[    6.652184] usb usb3: Manufacturer: Linux 2.6.26-2-686 ohci_hcd
[    6.652187] usb usb3: SerialNumber: 0000:02:0e.1
[    6.661823] hda: max request size: 128KiB
[    6.662185] hda: 78140160 sectors (40007 MB) w/7539KiB Cache, CHS=65535/16/63
[    6.666500] hda: cache flushes supported
[    6.666572]  hda: hda1 hda2 <<6>usbcore: registered new interface driver hiddev
[    6.700573] input: PS/2+USB Mouse as /class/input/input1
[    6.704858] input,hidraw0: USB HID v1.11 Mouse [PS/2+USB Mouse] on usb-0000:02:0e.0-1
[    6.704893] usbcore: registered new interface driver usbhid
[    6.704899] usbhid: v2.6:USB HID core driver
[    6.711594]  hda5 hda6 hda7 >
[    6.747317] hdc: ATAPI 24X DVD-ROM DVD-R-RAM CD-R/RW drive, 2048kB Cache
[    6.747329] Uniform CD-ROM driver Revision: 3.20
[    7.104564] PM: Starting manual resume from disk
[    7.188305] kjournald starting.  Commit interval 5 seconds
[    7.188305] EXT3-fs: mounted filesystem with ordered data mode.
[    9.318960] udev: starting version 141
[    9.318960] udev: deprecated sysfs layout; update the kernel or disable CONFIG_SYSFS_DEPRECATED; some udev features will not work correctly
[   10.282567] pci_hotplug: PCI Hot Plug PCI Core version: 0.5
[   10.285759] shpchp: Standard Hot Plug PCI Controller Driver version: 0.4
[   10.324623] input: Power Button (FF) as /class/input/input2
[   10.352139] ACPI: Power Button (FF) [PWRF]
[   10.352307] input: Sleep Button (CM) as /class/input/input3
[   10.384137] ACPI: Sleep Button (CM) [C19B]
[   10.384260] input: Lid Switch as /class/input/input4
[   10.400337] ACPI: Lid Switch [C19C]
[   10.401303] ACPI: AC Adapter [C19A] (on-line)
[   10.422996] input: Video Bus as /class/input/input5
[   10.448135] ACPI: Video Device [C0CE] (multi-head: yes  rom: no  post: no)
[   10.741957] ACPI: Battery Slot [C198] (battery absent)
[   10.742108] ACPI: Battery Slot [C199] (battery absent)
[   10.948308] ACPI: WMI: Mapper loaded
[   10.994312] Yenta: CardBus bridge found at 0000:02:06.0 [0e11:00b7]
[   10.994339] PCI: Bus 3, cardbus bridge: 0000:02:06.0
[   10.994342]   IO window: 0x00002800-0x000028ff
[   10.994348]   IO window: 0x00002c00-0x00002cff
[   10.994354]   PREFETCH window: 0x30400000-0x307fffff
[   10.994360]   MEM window: 0x34000000-0x37ffffff
[   10.994367] Yenta: Enabling burst memory read transactions
[   10.994373] Yenta: Using CSCINT to route CSC interrupts to PCI
[   10.994376] Yenta: Routing CardBus interrupts to PCI
[   10.994382] Yenta TI: socket 0000:02:06.0, mfunc 0x01001002, devctl 0x64
[   11.067299] intel_rng: FWH not detected
[   11.228608] Yenta: ISA IRQ mask 0x00b8, PCI irq 11
[   11.228614] Socket status: 30000020
[   11.228620] pcmcia: parent PCI bridge I/O window: 0x2000 - 0x2fff
[   11.228625] cs: IO port probe 0x2000-0x2fff: clean.
[   11.228958] pcmcia: parent PCI bridge Memory window: 0x40000000 - 0x403fffff
[   11.229301] Yenta: CardBus bridge found at 0000:02:06.1 [0e11:00b7]
[   11.229323] PCI: Bus 4, cardbus bridge: 0000:02:06.1
[   11.229327]   IO window: 0x00001400-0x000014ff
[   11.229332]   IO window: 0x00001800-0x000018ff
[   11.229337]   PREFETCH window: 0x30800000-0x30bfffff
[   11.229343]   MEM window: 0x38000000-0x3bffffff
[   11.229352] Yenta: Using CSCINT to route CSC interrupts to PCI
[   11.229355] Yenta: Routing CardBus interrupts to PCI
[   11.229361] Yenta TI: socket 0000:02:06.1, mfunc 0x01001002, devctl 0x64
[   11.372519] input: PC Speaker as /class/input/input6
[   11.460597] Yenta: ISA IRQ mask 0x00b8, PCI irq 11
[   11.460603] Socket status: 30000006
[   11.460608] Yenta: Raising subordinate bus# of parent bus (#02) from #04 to #07
[   11.460618] pcmcia: parent PCI bridge I/O window: 0x2000 - 0x2fff
[   11.460623] cs: IO port probe 0x2000-0x2fff: clean.
[   11.460946] pcmcia: parent PCI bridge Memory window: 0x40000000 - 0x403fffff
[   11.668279] NET: Registered protocol family 23
[   11.843181] ACPI: PCI Interrupt Link [C0C1] enabled at IRQ 11
[   11.843188] ACPI: PCI Interrupt 0000:00:1f.5[B] -> Link [C0C1] -> GSI 11 (level, low) -> IRQ 11
[   11.843212] PCI: Setting latency timer of device 0000:00:1f.5 to 64
[   11.864081] pccard: CardBus card inserted into slot 0
[   11.961059] Synaptics Touchpad, model: 1, fw: 5.8, id: 0x9b48b1, caps: 0x884793/0x0
[   11.961070] serio: Synaptics pass-through port at isa0060/serio4/input0
[   12.013891] input: SynPS/2 Synaptics TouchPad as /class/input/input7
[   12.044482] parport_pc 00:05: reported by Plug and Play ACPI
[   12.044541] parport0: PC-style at 0x378 (0x778), irq 7 [PCSPP,TRISTATE]
[   12.045825] found SMC SuperIO Chip (devid=0x0e rev=01 base=0x002e): LPC47N252
[   12.045845] smsc_ircc_present: can't get sir_base of 0x3e8
[   12.512046] intel8x0_measure_ac97_clock: measured 54717 usecs
[   12.512052] intel8x0: clocking to 48000
[   12.513519] ath5k_pci 0000:03:00.0: enabling device (0000 -> 0002)
[   12.513534] ACPI: PCI Interrupt 0000:03:00.0[A] -> Link [C0C3] -> GSI 11 (level, low) -> IRQ 11
[   12.513602] ath5k_pci 0000:03:00.0: registered as 'phy0'
[   12.606934] phy0: Selected rate control algorithm 'pid'
[   12.634204] cs: IO port probe 0x100-0x3af: excluding 0x100-0x107
[   12.635388] cs: IO port probe 0x3e0-0x4ff: clean.
[   12.635888] cs: IO port probe 0x820-0x8ff: clean.
[   12.636357] cs: IO port probe 0xc00-0xcf7: clean.
[   12.636931] cs: IO port probe 0xa00-0xaff: clean.
[   12.638190] cs: IO port probe 0x100-0x3af: excluding 0x100-0x107
[   12.639367] cs: IO port probe 0x3e0-0x4ff: clean.
[   12.639867] cs: IO port probe 0x820-0x8ff: clean.
[   12.640345] cs: IO port probe 0xc00-0xcf7: clean.
[   12.640920] cs: IO port probe 0xa00-0xaff: clean.
[   12.789305] ath5k phy0: Atheros AR2414 chip found (MAC: 0x79, PHY: 0x45)
[   13.732021] Adding 975200k swap on /dev/hda6.  Priority:-1 extents:1 across:975200k
[   14.164511] EXT3 FS on hda7, internal journal
[   14.472312] loop: module loaded
[   15.730540] PPP generic driver version 2.4.2
[   15.849222] NET: Registered protocol family 10
[   15.849875] lo: Disabled Privacy Extensions
[   15.850688] ADDRCONF(NETDEV_UP): eth0: link is not ready
[   19.246790] IBM TrackPoint firmware: 0x0b, buttons: 2/3
[   19.528573] input: TPPS/2 IBM TrackPoint as /class/input/input8
[   68.724927] [drm] Initialized drm 1.1.0 20060810
[   68.745232] ACPI: PCI Interrupt Link [C0C0] enabled at IRQ 11
[   68.745251] ACPI: PCI Interrupt 0000:01:00.0[A] -> Link [C0C0] -> GSI 11 (level, low) -> IRQ 11
[   68.745580] [drm] Initialized radeon 1.29.0 20080528 on minor 0
[   71.468317] agpgart: Found an AGP 2.0 compliant device at 0000:00:00.0.
[   71.468355] agpgart: Putting AGP V2 device at 0000:00:00.0 into 4x mode
[   71.468382] agpgart: Putting AGP V2 device at 0000:01:00.0 into 4x mode
[   72.901744] [drm] Setting GART location based on new memory map
[   72.901744] [drm] Loading R100 Microcode
[   72.901744] [drm] writeback test succeeded in 1 usecs
[  105.297004] fuse init (API version 7.9)
[  108.981872] agpgart: Found an AGP 2.0 compliant device at 0000:00:00.0.
[  108.981872] agpgart: Putting AGP V2 device at 0000:00:00.0 into 4x mode
[  108.981872] agpgart: Putting AGP V2 device at 0000:01:00.0 into 4x mode
[  108.981872] [drm] Loading R100 Microcode

next plik etc/network/interfaces:

Kod: Zaznacz cały

# This file describes the network interfaces available on your system
# and how to activate them. For more information, see interfaces(5).

# The loopback network interface
auto lo
iface lo inet loopback

auto dsl-provider
iface dsl-provider inet ppp
pre-up /sbin/ifconfig eth0 up # line maintained by pppoeconf
provider dsl-provider

auto eth0
iface eth0 inet manual

komenda ifconfig:

Kod: Zaznacz cały

eth0      Link encap:Ethernet  HWaddr 00:08:02:d8:b4:a2  
          UP BROADCAST MULTICAST  MTU:1500  Metric:1
          RX packets:0 errors:0 dropped:0 overruns:0 frame:0
          TX packets:0 errors:0 dropped:0 overruns:0 carrier:0
          collisions:0 txqueuelen:1000 
          RX bytes:0 (0.0 B)  TX bytes:0 (0.0 B)

lo        Link encap:Local Loopback  
          inet addr:127.0.0.1  Mask:255.0.0.0
          inet6 addr: ::1/128 Scope:Host
          UP LOOPBACK RUNNING  MTU:16436  Metric:1
          RX packets:8 errors:0 dropped:0 overruns:0 frame:0
          TX packets:8 errors:0 dropped:0 overruns:0 carrier:0
          collisions:0 txqueuelen:0 
          RX bytes:560 (560.0 B)  TX bytes:560 (560.0 B)

i ifconfig z parametrem -a:

Kod: Zaznacz cały

eth0      Link encap:Ethernet  HWaddr 00:08:02:d8:b4:a2  
          UP BROADCAST MULTICAST  MTU:1500  Metric:1
          RX packets:0 errors:0 dropped:0 overruns:0 frame:0
          TX packets:0 errors:0 dropped:0 overruns:0 carrier:0
          collisions:0 txqueuelen:1000 
          RX bytes:0 (0.0 B)  TX bytes:0 (0.0 B)

lo        Link encap:Local Loopback  
          inet addr:127.0.0.1  Mask:255.0.0.0
          inet6 addr: ::1/128 Scope:Host
          UP LOOPBACK RUNNING  MTU:16436  Metric:1
          RX packets:8 errors:0 dropped:0 overruns:0 frame:0
          TX packets:8 errors:0 dropped:0 overruns:0 carrier:0
          collisions:0 txqueuelen:0 
          RX bytes:560 (560.0 B)  TX bytes:560 (560.0 B)

wlan0     Link encap:Ethernet  HWaddr 00:1d:0f:f9:22:2c  
          BROADCAST MULTICAST  MTU:1500  Metric:1
          RX packets:0 errors:0 dropped:0 overruns:0 frame:0
          TX packets:0 errors:0 dropped:0 overruns:0 carrier:0
          collisions:0 txqueuelen:1000 
          RX bytes:0 (0.0 B)  TX bytes:0 (0.0 B)

wmaster0  Link encap:UNSPEC  HWaddr 00-1D-0F-F9-22-2C-6C-6F-00-00-00-00-00-00-00-00  
          BROADCAST MULTICAST  MTU:1500  Metric:1
          RX packets:0 errors:0 dropped:0 overruns:0 frame:0
          TX packets:0 errors:0 dropped:0 overruns:0 carrier:0
          collisions:0 txqueuelen:1000 
          RX bytes:0 (0.0 B)  TX bytes:0 (0.0 B)

komenda iwconfig:

Kod: Zaznacz cały

wlan0     IEEE 802.11  ESSID:""  
          Mode:Managed  Frequency:2.412 GHz  Access Point: Not-Associated   
          Tx-Power=0 dBm   
          Retry min limit:7   RTS thr :o ff   Fragment thr=2352 B   
          Encryption key :o ff
          Link Quality:0  Signal level:0  Noise level:0
          Rx invalid nwid:0  Rx invalid crypt:0  Rx invalid frag:0
          Tx excessive retries:0  Invalid misc:0   Missed beacon:0

iwconfig z parametrem -a zwraca tylko

Kod: Zaznacz cały

no such device

[Ister]

Dobrze, karta wykrywa się prawidłowo.
Podaj jeszcze zawartość pliku /etc/network/interfaces

i powiedz, czy masz zainstalowane jakieś narzędzia diagnostyczne (np wireless-tools)?

Używasz trybu tekstowego, czy środowiska graficznego, bo w sumie o to się jeszcze nie pytałem.
Generalnie wifi to jednak nie kabel i trzeba trochę więcej konfigurować. Rozumiem, że skoro mówimy o kluczu, to chodzi Ci o jedną konkretną sieć, nie o wszystkie otwarte sieci? Przynajmniej na razie?

[nahkranoth]

Zawartość pliku /etc/network/interfaces podałem już w poprzednim poście, ale o to i on:

Kod: Zaznacz cały

# This file describes the network interfaces available on your system 
# and how to activate them. For more information, see interfaces(5). 

# The loopback network interface 
auto lo 
iface lo inet loopback 

auto dsl-provider 
iface dsl-provider inet ppp 
pre-up /sbin/ifconfig eth0 up # line maintained by pppoeconf 
provider dsl-provider 

auto eth0 
iface eth0 inet manual

Mam tylko wireless-tools które są zainstalowane od razu z Debianem ale nie bardzo umiem z tego korzystać. Mam tylko tryb tekstowy, no dobrze mam graficzny ale to prawie czysty fluxbox z doinstalowaną Operą więc tak jak by go nie było. Chodzi mi o jedną sieć - moją małą domową sieć zabezpieczoną kluczem wep o czym pisałem w pierwszym poście. Ale fajnie by było wiedzieć jak łączyć się z innymi otwartymi sieciami np. z darmowymi acces pointami. Ale na razie chciałbym po prostu podłączyć się do mojej sieci i skonfigurować mniej lub bardziej system.

[Haseo]

Spróbuj tak:

Kod: Zaznacz cały

iwconfig wlan0 mode managed key [twój klucz wep] 
iwconfig essid "[nazwa sieci]"
dhclient wlan0

[nahkranoth]

Spróbuj tak

Kod: Zaznacz cały

iwconfig wlan0 mode managed key [twój klucz wep] 
iwconfig essid "[nazwa sieci]" 
dhclient wlan0

Pierwsza komenda chyba działa. Przy następnej jest już problem- podaje nazwe mojej sieci i od razu mi ją zwraca z błędem o nieistniejącej komendzie- samą nazwe sieci bez iwconfig essid.

[tmy123]

Kod: Zaznacz cały

iwconfig wlan0 essid "nazwa sieci"

Tak poza tym to

Kod: Zaznacz cały

iwlist wlan0 scan

powinno wyszukac twój ap i inne darmowe i tam będziesz miał ich parametry.