[+] Nie dzia

Wszystko związane z jądrem systemowym, sterownikami, sprzętem itp.
szcz00ri
Posty: 13
Rejestracja: 05 sierpnia 2009, 09:33
Lokalizacja: Inowrocław

[+] Nie działa karta WiFi Intel 5100

Post autor: szcz00ri » 19 listopada 2009, 16:32

Witam.

Podłącze się do tematu.

Laptop Lenovo IdeaPad G9550.

Nie mam pojęcia jak zainstalować bezprzewodową kartę sieciową.

Kod: Zaznacz cały

lspci

Kod: Zaznacz cały

04:00.0 Network controller: Intel Corporation PRO/Wireless 5100 AGN [Shiloh] Network Connection
07:00.0 Ethernet controller: Broadcom Corporation NetLink BCM5906M Fast Ethernet PCI Express (rev 02)

Kod: Zaznacz cały

ifconfig

Kod: Zaznacz cały

eth0      Link encap:Ethernet  HWaddr 00:26:22:05:14:a4
          inet addr:192.168.0.93  Bcast:192.168.0.255  Mask:255.255.255.0
          inet6 addr: fe80::226:22ff:fe05:14a4/64 Scope:Link
          UP BROADCAST RUNNING MULTICAST  MTU:1500  Metric:1
          RX packets:2247 errors:0 dropped:0 overruns:0 frame:0
          TX packets:2450 errors:0 dropped:0 overruns:0 carrier:0
          collisions:0 txqueuelen:1000
          RX bytes:1690674 (1.6 MiB)  TX bytes:481695 (470.4 KiB)
          Interrupt:17

lo        Link encap:Local Loopback
          inet addr:127.0.0.1  Mask:255.0.0.0
          inet6 addr: ::1/128 Scope:Host
          UP LOOPBACK RUNNING  MTU:16436  Metric:1
          RX packets:52 errors:0 dropped:0 overruns:0 frame:0
          TX packets:52 errors:0 dropped:0 overruns:0 carrier:0
          collisions:0 txqueuelen:0
          RX bytes:3280 (3.2 KiB)  TX bytes:3280 (3.2 KiB)
i tu jest problem:

Kod: Zaznacz cały

iwconfig

Kod: Zaznacz cały

lo        no wireless extensions.

eth0      no wireless extensions.
korzystam z

Kod: Zaznacz cały

wicd
internet kablem ładnie mi widzi, nie muszę nic konfigurować

Kilka godzin "googlowania" i nie znalazłem nic konkretnego. Większość postów dotyczy konfiguracji internetu bezprzewodowego zakładając, że są sterowniki do karty bezprzewodowej zainstalowane.

Zainstalowałem również:

Kod: Zaznacz cały

bcm5700-source
ale nie znalazłem nigdzie jak to wrzucić do uruchamianych modułów, może w tym jest moja niewiedza.

Zainstalowane również:

Kod: Zaznacz cały

wireless-tools
Proszę o podpowiedź jak rozwiązać ten problem.

AdeBe
Junior Member
Posty: 825
Rejestracja: 01 grudnia 2007, 14:41

Post autor: AdeBe » 19 listopada 2009, 17:13

szcz00ri, wydzieliłem twój post z poprzedniego tematu.
Nie "podpinaj się" pod tematy nie związane bezpośrednio z twoim problemem. Szczególnie, gdy taki temat nie jest najświeższy.



Pakiet

Kod: Zaznacz cały

 bcm5700-source
raczej nie jest Ci potrzebny.
Masz kartę WiFi Intela, sprawdź czy masz zainstalowany pakiet

Kod: Zaznacz cały

firmware-iwlwifi
Jeśli nie, to zainstaluj i zrestartuj komputer.
Jeśli nadal nie będzie działało lub masz ten pakiet zainstalowany, to wklej wynik polecenia

Kod: Zaznacz cały

dmesg
Aha, byłbym zapomniał: podaj wersję Debiana i kernela.

szcz00ri
Posty: 13
Rejestracja: 05 sierpnia 2009, 09:33
Lokalizacja: Inowrocław

Post autor: szcz00ri » 19 listopada 2009, 18:06

Wstyd, nie znać swojego sprzętu.

dmesgg

Kod: Zaznacz cały

[    0.000000] Initializing cgroup subsys cpuset
[    0.000000] Initializing cgroup subsys cpu
[    0.000000] Linux version 2.6.26-2-686 (Debian 2.6.26-19lenny2) (dannf@debian.org) (gcc version 4.1.3 20080704 (prerelease) (Debian 4.1.2-25)) #1 SMP Wed Nov 4 20:45:37 UTC 2009
[    0.000000] BIOS-provided physical RAM map:
[    0.000000]  BIOS-e820: 0000000000000000 - 000000000009f400 (usable)
[    0.000000]  BIOS-e820: 000000000009f400 - 00000000000a0000 (reserved)
[    0.000000]  BIOS-e820: 00000000000d2000 - 00000000000d4000 (reserved)
[    0.000000]  BIOS-e820: 00000000000dc000 - 0000000000100000 (reserved)
[    0.000000]  BIOS-e820: 0000000000100000 - 00000000bdaa1000 (usable)
[    0.000000]  BIOS-e820: 00000000bdaa1000 - 00000000bdaa7000 (reserved)
[    0.000000]  BIOS-e820: 00000000bdaa7000 - 00000000bdbba000 (usable)
[    0.000000]  BIOS-e820: 00000000bdbba000 - 00000000bdc0f000 (reserved)
[    0.000000]  BIOS-e820: 00000000bdc0f000 - 00000000bdd08000 (usable)
[    0.000000]  BIOS-e820: 00000000bdd08000 - 00000000bdf0f000 (reserved)
[    0.000000]  BIOS-e820: 00000000bdf0f000 - 00000000bdf19000 (usable)
[    0.000000]  BIOS-e820: 00000000bdf19000 - 00000000bdf1f000 (reserved)
[    0.000000]  BIOS-e820: 00000000bdf1f000 - 00000000bdf64000 (usable)
[    0.000000]  BIOS-e820: 00000000bdf64000 - 00000000bdf9f000 (ACPI NVS)
[    0.000000]  BIOS-e820: 00000000bdf9f000 - 00000000be000000 (ACPI data)
[    0.000000]  BIOS-e820: 0000000100000000 - 0000000140000000 (usable)
[    0.000000] Warning only 4GB will be used.
[    0.000000] Use a HIGHMEM64G enabled kernel.
[    0.000000] 3200MB HIGHMEM available.
[    0.000000] 896MB LOWMEM available.
[    0.000000] found SMP MP-table at [c00f75c0] 000f75c0
[    0.000000] Entering add_active_range(0, 0, 1048576) 0 entries of 256 used
[    0.000000] Zone PFN ranges:
[    0.000000]   DMA             0 ->     4096
[    0.000000]   Normal       4096 ->   229376
[    0.000000]   HighMem    229376 ->  1048576
[    0.000000] Movable zone start PFN for each node
[    0.000000] early_node_map[1] active PFN ranges
[    0.000000]     0:        0 ->  1048576
[    0.000000] On node 0 totalpages: 1048576
[    0.000000]   DMA zone: 32 pages used for memmap
[    0.000000]   DMA zone: 0 pages reserved
[    0.000000]   DMA zone: 4064 pages, LIFO batch:0
[    0.000000]   Normal zone: 1760 pages used for memmap
[    0.000000]   Normal zone: 223520 pages, LIFO batch:31
[    0.000000]   HighMem zone: 6400 pages used for memmap
[    0.000000]   HighMem zone: 812800 pages, LIFO batch:31
[    0.000000]   Movable zone: 0 pages used for memmap
[    0.000000] DMI present.
[    0.000000] ACPI: RSDP 000F7530, 0024 (r2 LENOVO)
[    0.000000] ACPI: XSDT BDFF8423, 0074 (r1 LENOVO CB-01           0  LTP        0)
[    0.000000] ACPI: FACP BDFE8000, 00F4 (r3 LENOVO CB-01           1 ALAN        1)
[    0.000000] ACPI: DSDT BDFE9000, 672B (r2 LENOVO CB-01           1 INTL 20050624)
[    0.000000] ACPI: FACS BDF9EFC0, 0040
[    0.000000] ACPI: HPET BDFFED52, 0038 (r1 LENOVO CB-01           1 LOHR       5A)
[    0.000000] ACPI: MCFG BDFFED8A, 003C (r1 LENOVO CB-01           1 LOHR       5A)
[    0.000000] ACPI: SLIC BDFFEDC6, 0176 (r1 LENOVO CB-01           1 TBD         1)
[    0.000000] ACPI: DBGP BDFFEF3C, 0034 (r1 LENOVO CB-01           1 LOHR        0)
[    0.000000] ACPI: APIC BDFFEF70, 0068 (r1 PTLTD       APIC          0  LTP        0)
[    0.000000] ACPI: BOOT BDFFEFD8, 0028 (r1 PTLTD  $SBFTBL$        0  LTP        1)
[    0.000000] ACPI: SSDT BDFE7000, 0655 (r1  PmRef    CpuPm     3000 INTL 20050624)
[    0.000000] ACPI: SSDT BDFE6000, 0259 (r1  PmRef  Cpu0Tst     3000 INTL 20050624)
[    0.000000] ACPI: SSDT BDFE5000, 020F (r1  PmRef    ApTst     3000 INTL 20050624)
[    0.000000] ACPI: PM-Timer IO Port: 0x408
[    0.000000] ACPI: Local APIC address 0xfee00000
[    0.000000] ACPI: LAPIC (acpi_id[0x00] lapic_id[0x00] enabled)
[    0.000000] ACPI: LAPIC (acpi_id[0x01] lapic_id[0x01] enabled)
[    0.000000] ACPI: LAPIC_NMI (acpi_id[0x00] high edge lint[0x1])
[    0.000000] ACPI: LAPIC_NMI (acpi_id[0x01] high edge lint[0x1])
[    0.000000] ACPI: IOAPIC (id[0x02] address[0xfec00000] gsi_base[0])
[    0.000000] IOAPIC[0]: apic_id 2, version 32, address 0xfec00000, GSI 0-23
[    0.000000] ACPI: INT_SRC_OVR (bus 0 bus_irq 0 global_irq 2 high edge)
[    0.000000] ACPI: INT_SRC_OVR (bus 0 bus_irq 9 global_irq 9 high level)
[    0.000000] ACPI: IRQ0 used by override.
[    0.000000] ACPI: IRQ2 used by override.
[    0.000000] ACPI: IRQ9 used by override.
[    0.000000] Enabling APIC mode:  Flat.  Using 1 I/O APICs
[    0.000000] ACPI: HPET id: 0x8086a201 base: 0xfed00000
[    0.000000] Using ACPI (MADT) for SMP configuration information
[    0.000000] Allocating PCI resources starting at c0000000 (gap: be000000:42000000)
[    0.000000] PM: Registered nosave memory: 000000000009f000 - 00000000000a0000
[    0.000000] PM: Registered nosave memory: 00000000000a0000 - 00000000000d2000
[    0.000000] PM: Registered nosave memory: 00000000000d2000 - 00000000000d4000
[    0.000000] PM: Registered nosave memory: 00000000000d4000 - 00000000000dc000
[    0.000000] PM: Registered nosave memory: 00000000000dc000 - 0000000000100000
[    0.000000] SMP: Allowing 2 CPUs, 0 hotplug CPUs
[    0.000000] PERCPU: Allocating 37992 bytes of per cpu data
[    0.000000] NR_CPUS: 8, nr_cpu_ids: 2
[    0.000000] Built 1 zonelists in Zone order, mobility grouping on.  Total pages: 1040384
[    0.000000] Kernel command line: root=/dev/sda1 ro splash vga=791 quiet quiet
[    0.000000] mapped APIC to ffffb000 (fee00000)
[    0.000000] mapped IOAPIC to ffffa000 (fec00000)
[    0.000000] Enabling fast FPU save and restore... done.
[    0.000000] Enabling unmasked SIMD FPU exception support... done.
[    0.000000] Initializing CPU#0
[    0.000000] PID hash table entries: 4096 (order: 12, 16384 bytes)
[    0.000000] Extended CMOS year: 2000
[    0.000000] Detected 2094.857 MHz processor.
[    0.004000] Console: colour dummy device 80x25
[    0.004000] console [tty0] enabled
[    0.004000] Dentry cache hash table entries: 131072 (order: 7, 524288 bytes)
[    0.004000] Inode-cache hash table entries: 65536 (order: 6, 262144 bytes)
[    0.004000] Memory: 3063064k/4194304k available (1770k kernel code, 45524k reserved, 750k data, 244k init, 2192368k highmem)
[    0.004000] virtual kernel memory layout:
[    0.004000]     fixmap  : 0xfff4c000 - 0xfffff000   ( 716 kB)
[    0.004000]     pkmap   : 0xff800000 - 0xffc00000   (4096 kB)
[    0.004000]     vmalloc : 0xf8800000 - 0xff7fe000   ( 111 MB)
[    0.004000]     lowmem  : 0xc0000000 - 0xf8000000   ( 896 MB)
[    0.004000]       .init : 0xc037f000 - 0xc03bc000   ( 244 kB)
[    0.004000]       .data : 0xc02baaa1 - 0xc0376620   ( 750 kB)
[    0.004000]       .text : 0xc0100000 - 0xc02baaa1   (1770 kB)
[    0.004000] Checking if this processor honours the WP bit even in supervisor mode...Ok.
[    0.004000] CPA: page pool initialized 1 of 1 pages preallocated
[    0.004000] hpet clockevent registered
[    0.083861] Calibrating delay using timer specific routine.. 4193.86 BogoMIPS (lpj=8387727)
[    0.083890] Security Framework initialized
[    0.083895] SELinux:  Disabled at boot.
[    0.083898] Capability LSM initialized
[    0.083909] Mount-cache hash table entries: 512
[    0.084005] Initializing cgroup subsys ns
[    0.084005] Initializing cgroup subsys cpuacct
[    0.084005] Initializing cgroup subsys devices
[    0.084005] CPU: L1 I cache: 32K, L1 D cache: 32K
[    0.084005] CPU: L2 cache: 2048K
[    0.084005] CPU: Physical Processor ID: 0
[    0.084005] CPU: Processor Core ID: 0
[    0.084005] Intel machine check architecture supported.
[    0.084005] Intel machine check reporting enabled on CPU#0.
[    0.084005] using mwait in idle threads.
[    0.084005] Checking 'hlt' instruction... OK.
[    0.100006] ACPI: Core revision 20080321
[    0.112007] ENABLING IO-APIC IRQs
[    0.112007] ..TIMER: vector=0x31 apic1=0 pin1=2 apic2=-1 pin2=-1
[    0.151665] CPU0: Intel(R) Core(TM)2 Duo CPU     T6500  @ 2.10GHz stepping 0a
[    0.152009] Booting processor 1/1 ip 6000
[    0.160010] Initializing CPU#1
[    0.160010] Calibrating delay using timer specific routine.. 4189.46 BogoMIPS (lpj=8378922)
[    0.160010] CPU: L1 I cache: 32K, L1 D cache: 32K
[    0.160010] CPU: L2 cache: 2048K
[    0.160010] CPU: Physical Processor ID: 0
[    0.160010] CPU: Processor Core ID: 1
[    0.160010] Intel machine check architecture supported.
[    0.160010] Intel machine check reporting enabled on CPU#1.
[    0.240015] CPU1: Intel(R) Core(TM)2 Duo CPU     T6500  @ 2.10GHz stepping 0a
[    0.240015] checking TSC synchronization [CPU#0 -> CPU#1]: passed.
[    0.244015] Brought up 2 CPUs
[    0.244015] Total of 2 processors activated (8383.32 BogoMIPS).
[    0.244015] CPU0 attaching sched-domain:
[    0.244015]  domain 0: span 0-1
[    0.244015]   groups: 0 1
[    0.244015] CPU1 attaching sched-domain:
[    0.244015]  domain 0: span 0-1
[    0.244015]   groups: 1 0
[    0.244015] net_namespace: 660 bytes
[    0.244015] Booting paravirtualized kernel on bare hardware
[    0.244015] NET: Registered protocol family 16
[    0.244015] ACPI: bus type pci registered
[    0.244015] PCI: MCFG configuration 0: base e0000000 segment 0 buses 0 - 255
[    0.244015] PCI: Not using MMCONFIG.
[    0.244015] PCI: PCI BIOS revision 3.00 entry at 0xfde21, last bus=8
[    0.244015] PCI: Using configuration type 1 for base access
[    0.244015] Setting up standard PCI resources
[    0.248015] ACPI: EC: Look up EC in DSDT
[    0.250890] ACPI: BIOS _OSI(Linux) query ignored
[    0.250892] ACPI: DMI System Vendor: LENOVO
[    0.250894] ACPI: DMI Product Name: 20023
[    0.250895] ACPI: DMI Product Version: Lenovo G550
[    0.250897] ACPI: DMI Board Name: NITU1
[    0.250898] ACPI: DMI BIOS Vendor: LENOVO
[    0.250899] ACPI: DMI BIOS Date: 08/05/2009
[    0.250901] ACPI: Please send DMI info above to [email]linux-acpi@vger.kernel.org[/email]
[    0.250903] ACPI: If "acpi_osi=Linux" works better, please notify [email]linux-acpi@vger.kernel.org[/email]
[    0.256016] ACPI: Interpreter enabled
[    0.256018] ACPI: (supports S0 S3 S4 S5)
[    0.256464] ACPI: Using IOAPIC for interrupt routing
[    0.256464] PCI: MCFG configuration 0: base e0000000 segment 0 buses 0 - 255
[    0.293026] PCI: MCFG area at e0000000 reserved in ACPI motherboard resources
[    0.293028] PCI: Using MMCONFIG for extended config space
[    0.296467] ACPI: EC: non-query interrupt received, switching to interrupt mode
[    0.356471] ACPI: EC: GPE = 0x1c, I/O: command/status = 0x66, data = 0x62
[    0.356471] ACPI: EC: driver started in interrupt mode
[    0.356471] ACPI: PCI Root Bridge [PCI0] (0000:00)
[    0.361483] PCI: Transparent bridge - 0000:00:1e.0
[    0.361539] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0._PRT]
[    0.361743] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.P0P2._PRT]
[    0.361883] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.RP01._PRT]
[    0.361993] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.RP02._PRT]
[    0.362100] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.RP03._PRT]
[    0.362210] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.RP04._PRT]
[    0.362320] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.RP06._PRT]
[    0.370928] ACPI: PCI Interrupt Link [LNKA] (IRQs 1 3 4 *5 6 7 10 12 14 15)
[    0.370928] ACPI: PCI Interrupt Link [LNKB] (IRQs 1 3 4 5 6 7 *11 12 14 15)
[    0.370928] ACPI: PCI Interrupt Link [LNKC] (IRQs 1 *3 4 5 6 7 10 12 14 15)
[    0.370928] ACPI: PCI Interrupt Link [LNKD] (IRQs 1 3 4 5 6 7 11 12 14 15) *10
[    0.370928] ACPI: PCI Interrupt Link [LNKE] (IRQs 1 3 4 5 6 *7 10 12 14 15)
[    0.370928] ACPI: PCI Interrupt Link [LNKF] (IRQs 1 3 4 5 6 7 *11 12 14 15)
[    0.370928] ACPI: PCI Interrupt Link [LNKG] (IRQs 1 3 4 5 6 7 *10 12 14 15)
[    0.370928] ACPI: PCI Interrupt Link [LNKH] (IRQs 1 3 *4 5 6 7 11 12 14 15)
[    0.370928] Linux Plug and Play Support v0.97 (c) Adam Belay
[    0.370928] pnp: PnP ACPI init
[    0.370928] ACPI: bus type pnp registered
[    0.391554] pnp: PnP ACPI: found 10 devices
[    0.391554] ACPI: ACPI bus type pnp unregistered
[    0.391554] PnPBIOS: Disabled by ACPI PNP
[    0.391554] PCI: Using ACPI for IRQ routing
[    0.398447] hpet0: at MMIO 0xfed00000, IRQs 2, 8, 0, 0
[    0.398452] hpet0: 4 64-bit timers, 14318180 Hz
[    0.402384] ACPI: RTC can wake from S4
[    0.409324] system 00:03: iomem range 0xfed00000-0xfed003ff has been reserved
[    0.409330] system 00:05: ioport range 0x680-0x69f has been reserved
[    0.409333] system 00:05: ioport range 0x480-0x48f has been reserved
[    0.409335] system 00:05: ioport range 0xffff-0xffff has been reserved
[    0.409337] system 00:05: ioport range 0xffff-0xffff has been reserved
[    0.409340] system 00:05: ioport range 0x400-0x47f has been reserved
[    0.409342] system 00:05: ioport range 0x1180-0x11ff has been reserved
[    0.409344] system 00:05: ioport range 0x164e-0x164f has been reserved
[    0.409346] system 00:05: ioport range 0xfe00-0xfe00 has been reserved
[    0.409353] system 00:09: iomem range 0xfed1c000-0xfed1ffff has been reserved
[    0.409356] system 00:09: iomem range 0xfed10000-0xfed13fff has been reserved
[    0.409358] system 00:09: iomem range 0xfed18000-0xfed18fff has been reserved
[    0.409360] system 00:09: iomem range 0xfed19000-0xfed19fff has been reserved
[    0.409363] system 00:09: iomem range 0xe0000000-0xefffffff has been reserved
[    0.409365] system 00:09: iomem range 0xfed20000-0xfed3ffff has been reserved
[    0.409368] system 00:09: iomem range 0xfed45000-0xfed8ffff has been reserved
[    0.438441] PCI: Failed to allocate mem resource #6:20000@e0000000 for 0000:01:00.0
[    0.438441] PCI: Bridge: 0000:00:01.0
[    0.438441]   IO window: 2000-2fff
[    0.438441]   MEM window: 0xf4000000-0xf6ffffff
[    0.438441]   PREFETCH window: 0x00000000d0000000-0x00000000dfffffff
[    0.438441] PCI: Bridge: 0000:00:1c.0
[    0.438441]   IO window: disabled.
[    0.438441]   MEM window: disabled.
[    0.438441]   PREFETCH window: disabled.
[    0.438441] PCI: Bridge: 0000:00:1c.1
[    0.438441]   IO window: disabled.
[    0.438441]   MEM window: disabled.
[    0.438441]   PREFETCH window: disabled.
[    0.438441] PCI: Bridge: 0000:00:1c.2
[    0.438441]   IO window: disabled.
[    0.438441]   MEM window: 0xf7100000-0xf71fffff
[    0.438441]   PREFETCH window: disabled.
[    0.438441] PCI: Bridge: 0000:00:1c.3
[    0.438441]   IO window: 3000-3fff
[    0.438441]   MEM window: 0xf0000000-0xf3ffffff
[    0.438441]   PREFETCH window: 0x00000000f8000000-0x00000000f9ffffff
[    0.438441] PCI: Bridge: 0000:00:1c.5
[    0.438441]   IO window: disabled.
[    0.438441]   MEM window: 0xf7000000-0xf70fffff
[    0.438441]   PREFETCH window: disabled.
[    0.438441] PCI: Bridge: 0000:00:1e.0
[    0.438441]   IO window: disabled.
[    0.438441]   MEM window: disabled.
[    0.438441]   PREFETCH window: disabled.
[    0.438441] ACPI: PCI Interrupt 0000:00:01.0[A] -> GSI 16 (level, low) -> IRQ 16
[    0.438441] PCI: Setting latency timer of device 0000:00:01.0 to 64
[    0.438441] ACPI: PCI Interrupt 0000:00:1c.0[A] -> GSI 17 (level, low) -> IRQ 17
[    0.438441] PCI: Setting latency timer of device 0000:00:1c.0 to 64
[    0.438441] ACPI: PCI Interrupt 0000:00:1c.1[B] -> GSI 16 (level, low) -> IRQ 16
[    0.438441] PCI: Setting latency timer of device 0000:00:1c.1 to 64
[    0.438441] ACPI: PCI Interrupt 0000:00:1c.2[C] -> GSI 18 (level, low) -> IRQ 18
[    0.438441] PCI: Setting latency timer of device 0000:00:1c.2 to 64
[    0.438441] ACPI: PCI Interrupt 0000:00:1c.3[D] -> GSI 19 (level, low) -> IRQ 19
[    0.438441] PCI: Setting latency timer of device 0000:00:1c.3 to 64
[    0.438441] ACPI: PCI Interrupt 0000:00:1c.5[B] -> GSI 16 (level, low) -> IRQ 16
[    0.438442] PCI: Setting latency timer of device 0000:00:1c.5 to 64
[    0.438442] PCI: Setting latency timer of device 0000:00:1e.0 to 64
[    0.438442] NET: Registered protocol family 2
[    0.451723] IP route cache hash table entries: 32768 (order: 5, 131072 bytes)
[    0.451913] TCP established hash table entries: 131072 (order: 8, 1048576 bytes)
[    0.452227] TCP bind hash table entries: 65536 (order: 7, 524288 bytes)
[    0.454092] TCP: Hash tables configured (established 131072 bind 65536)
[    0.454095] TCP reno registered
[    0.461408] NET: Registered protocol family 1
[    0.461496] checking if image is initramfs...<7>Switched to high resolution mode on CPU 1
[    0.515489] Switched to high resolution mode on CPU 0
[    0.743593]  it is
[    1.043603] Freeing initrd memory: 8564k freed
[    1.043604] Simple Boot Flag at 0x36 set to 0x1
[    1.043972] audit: initializing netlink socket (disabled)
[    1.043972] type=2000 audit(1258649924.028:1): initialized
[    1.043972] highmem bounce pool size: 64 pages
[    1.043972] Total HugeTLB memory allocated, 0
[    1.043972] VFS: Disk quotas dquot_6.5.1
[    1.043972] Dquot-cache hash table entries: 1024 (order 0, 4096 bytes)
[    1.043972] msgmni has been set to 1719
[    1.043972] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 253)
[    1.043972] io scheduler noop registered
[    1.043972] io scheduler anticipatory registered
[    1.043972] io scheduler deadline registered
[    1.043972] io scheduler cfq registered (default)
[    1.043972] pci 0000:01:00.0: Boot video device
[    1.043972] PCI: Setting latency timer of device 0000:00:01.0 to 64
[    1.043972] assign_interrupt_mode Found MSI capability
[    1.043972] Allocate Port Service[0000:00:01.:p cie00]
[    1.043972] Allocate Port Service[0000:00:01.:p cie02]
[    1.043972] Allocate Port Service[0000:00:01.:p cie03]
[    1.043972] PCI: Setting latency timer of device 0000:00:1c.0 to 64
[    1.043972] assign_interrupt_mode Found MSI capability
[    1.043972] Allocate Port Service[0000:00:1c.:p cie00]
[    1.043972] Allocate Port Service[0000:00:1c.:p cie02]
[    1.043972] Allocate Port Service[0000:00:1c.:p cie03]
[    1.043972] PCI: Setting latency timer of device 0000:00:1c.1 to 64
[    1.043972] assign_interrupt_mode Found MSI capability
[    1.043972] Allocate Port Service[0000:00:1c.1 :p cie00]
[    1.043972] Allocate Port Service[0000:00:1c.1 :p cie02]
[    1.043972] Allocate Port Service[0000:00:1c.1 :p cie03]
[    1.043972] PCI: Setting latency timer of device 0000:00:1c.2 to 64
[    1.043972] assign_interrupt_mode Found MSI capability
[    1.043972] Allocate Port Service[0000:00:1c.2 :p cie00]
[    1.043972] Allocate Port Service[0000:00:1c.2 :p cie02]
[    1.043972] Allocate Port Service[0000:00:1c.2 :p cie03]
[    1.043972] PCI: Setting latency timer of device 0000:00:1c.3 to 64
[    1.043972] assign_interrupt_mode Found MSI capability
[    1.043972] Allocate Port Service[0000:00:1c.3 :p cie00]
[    1.043972] Allocate Port Service[0000:00:1c.3 :p cie02]
[    1.043972] Allocate Port Service[0000:00:1c.3 :p cie03]
[    1.043972] PCI: Setting latency timer of device 0000:00:1c.5 to 64
[    1.043972] assign_interrupt_mode Found MSI capability
[    1.043972] Allocate Port Service[0000:00:1c.5 :p cie00]
[    1.043972] Allocate Port Service[0000:00:1c.5 :p cie02]
[    1.043972] Allocate Port Service[0000:00:1c.5 :p cie03]
[    1.044254] vesafb: framebuffer at 0xf5000000, mapped to 0xf8880000, using 3072k, total 14336k
[    1.044257] vesafb: mode is 1024x768x16, linelength=2048, pages=1
[    1.044259] vesafb: protected mode interface info at c000:cd10
[    1.044261] vesafb: pmi: set display start = c00ccd73, set palette = c00ccdce
[    1.044263] vesafb: pmi: ports = 3b4 3b5 3ba 3c0 3c1 3c4 3c5 3c6 3c7 3c8 3c9 3cc 3ce 3cf 3d0 3d1 3d2 3d3 3d4 3d5 3da
[    1.044272] vesafb: scrolling: redraw
[    1.044274] vesafb: Truecolor: size=0:5:6:5, shift=0:11:5:0
[    1.068955] Console: switching to colour frame buffer device 128x48
[    1.093581] fb0: VESA VGA frame buffer device
[    1.095971] isapnp: Scanning for PnP cards...
[    1.407973] isapnp: No Plug & Play device found
[    1.407973] hpet_resources: 0xfed00000 is busy
[    1.407973] Serial: 8250/16550 driver $Revision: 1.90 $ 4 ports, IRQ sharing enabled
[    1.407984] brd: module loaded
[    1.407984] PNP: PS/2 Controller [PNP0303:PS2K,PNP0f13:PS2M] at 0x60,0x64 irq 1,12
[    1.498503] serio: i8042 KBD port at 0x60,0x64 irq 1
[    1.498506] serio: i8042 AUX port at 0x60,0x64 irq 12
[    1.500659] mice: PS/2 mouse device common for all mice
[    1.500659] rtc_cmos 00:06: rtc core: registered rtc_cmos as rtc0
[    1.500659] rtc0: alarms up to one month, y3k
[    1.500659] cpuidle: using governor ladder
[    1.500659] cpuidle: using governor menu
[    1.500659] No iBFT detected.
[    1.502037] TCP cubic registered
[    1.502040] NET: Registered protocol family 17
[    1.502047] Using IPI No-Shortcut mode
[    1.504991] registered taskstats version 1
[    1.504991] rtc_cmos 00:06: setting system clock to 2009-11-19 16:58:45 UTC (1258649925)
[    1.504991] Freeing unused kernel memory: 244k freed
[    1.585656] input: AT Translated Set 2 keyboard as /class/input/input0
[    1.617532] ACPI: SSDT BDF1ACA0, 0223 (r1  PmRef  Cpu0Ist     3000 INTL 20050624)
[    1.617956] ACPI: SSDT BDF19620, 0549 (r1  PmRef  Cpu0Cst     3001 INTL 20050624)
[    1.618132] Monitor-Mwait will be used to enter C-1 state
[    1.618132] Monitor-Mwait will be used to enter C-2 state
[    1.618132] ACPI: CPU0 (power states: C1[C1] C2[C2])
[    1.618132] ACPI: ACPI0007:00 is registered as cooling_device0
[    1.618132] ACPI: Processor [CPU0] (supports 8 throttling states)
[    1.618132] ACPI: SSDT BDF1AA20, 01CF (r1  PmRef    ApIst     3000 INTL 20050624)
[    1.618132] ACPI: SSDT BDF1AF20, 008D (r1  PmRef    ApCst     3000 INTL 20050624)
[    1.629864] Marking TSC unstable due to: TSC halts in idle.
[    1.631869] ACPI: CPU1 (power states: C1[C1] C2[C2])
[    1.631869] ACPI: ACPI0007:01 is registered as cooling_device1
[    1.631869] ACPI: Processor [CPU1] (supports 8 throttling states)
[    1.633591] ACPI: LNXTHERM:01 is registered as thermal_zone0
[    1.639017] ACPI: Thermal Zone [TZ00] (45 C)
[    1.847501] usbcore: registered new interface driver usbfs
[    1.847501] usbcore: registered new interface driver hub
[    1.859500] usbcore: registered new device driver usb
[    1.867428] USB Universal Host Controller Interface driver v3.0
[    1.867465] ACPI: PCI Interrupt 0000:00:1a.0[A] -> GSI 16 (level, low) -> IRQ 16
[    1.867474] PCI: Setting latency timer of device 0000:00:1a.0 to 64
[    1.867478] uhci_hcd 0000:00:1a.0: UHCI Host Controller
[    1.867575] uhci_hcd 0000:00:1a.0: new USB bus registered, assigned bus number 1
[    1.867612] uhci_hcd 0000:00:1a.0: irq 16, io base 0x00001800
[    1.867680] usb usb1: configuration #1 chosen from 1 choice
[    1.867704] hub 1-0:1.0: USB hub found
[    1.867710] hub 1-0:1.0: 2 ports detected
[    1.914439] No dock devices found.
[    1.930411] SCSI subsystem initialized
[    1.942998] libata version 3.00 loaded.
[    1.970540] usb usb1: New USB device found, idVendor=1d6b, idProduct=0001
[    1.970544] usb usb1: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[    1.970546] usb usb1: Product: UHCI Host Controller
[    1.970548] usb usb1: Manufacturer: Linux 2.6.26-2-686 uhci_hcd
[    1.970549] usb usb1: SerialNumber: 0000:00:1a.0
[    1.972610] ACPI: PCI Interrupt 0000:00:1a.1[B] -> GSI 21 (level, low) -> IRQ 21
[    1.972619] PCI: Setting latency timer of device 0000:00:1a.1 to 64
[    1.972623] uhci_hcd 0000:00:1a.1: UHCI Host Controller
[    1.972642] uhci_hcd 0000:00:1a.1: new USB bus registered, assigned bus number 2
[    1.972674] uhci_hcd 0000:00:1a.1: irq 21, io base 0x00001820
[    1.972737] usb usb2: configuration #1 chosen from 1 choice
[    1.972760] hub 2-0:1.0: USB hub found
[    1.972765] hub 2-0:1.0: 2 ports detected
[    2.074384] usb usb2: New USB device found, idVendor=1d6b, idProduct=0001
[    2.074390] usb usb2: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[    2.074393] usb usb2: Product: UHCI Host Controller
[    2.074396] usb usb2: Manufacturer: Linux 2.6.26-2-686 uhci_hcd
[    2.074399] usb usb2: SerialNumber: 0000:00:1a.1
[    2.077491] ACPI: PCI Interrupt 0000:00:1a.2[C] -> GSI 20 (level, low) -> IRQ 20
[    2.077491] PCI: Setting latency timer of device 0000:00:1a.2 to 64
[    2.077491] uhci_hcd 0000:00:1a.2: UHCI Host Controller
[    2.077491] uhci_hcd 0000:00:1a.2: new USB bus registered, assigned bus number 3
[    2.077491] uhci_hcd 0000:00:1a.2: irq 20, io base 0x00001840
[    2.077491] usb usb3: configuration #1 chosen from 1 choice
[    2.077491] hub 3-0:1.0: USB hub found
[    2.077491] hub 3-0:1.0: 2 ports detected
[    2.180493] usb usb3: New USB device found, idVendor=1d6b, idProduct=0001
[    2.180498] usb usb3: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[    2.180502] usb usb3: Product: UHCI Host Controller
[    2.180505] usb usb3: Manufacturer: Linux 2.6.26-2-686 uhci_hcd
[    2.180508] usb usb3: SerialNumber: 0000:00:1a.2
[    2.180736] ACPI: PCI Interrupt 0000:00:1a.7[C] -> GSI 20 (level, low) -> IRQ 20
[    2.180736] PCI: Setting latency timer of device 0000:00:1a.7 to 64
[    2.180736] ehci_hcd 0000:00:1a.7: EHCI Host Controller
[    2.180736] ehci_hcd 0000:00:1a.7: new USB bus registered, assigned bus number 4
[    2.181884] ehci_hcd 0000:00:1a.7: debug port 1
[    2.181890] PCI: cache line size of 32 is not supported by device 0000:00:1a.7
[    2.181894] ehci_hcd 0000:00:1a.7: irq 20, io mem 0xf7405800
[    2.212922] usb 1-1: new full speed USB device using uhci_hcd and address 2
[    2.225669] ehci_hcd 0000:00:1a.7: USB 2.0 started, EHCI 1.00, driver 10 Dec 2004
[    2.225749] usb usb4: configuration #1 chosen from 1 choice
[    2.225789] hub 4-0:1.0: USB hub found
[    2.225799] hub 4-0:1.0: 6 ports detected
[    2.280712] hub 1-0:1.0: unable to enumerate USB device on port 1
[    2.329960] usb usb4: New USB device found, idVendor=1d6b, idProduct=0002
[    2.329960] usb usb4: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[    2.329960] usb usb4: Product: EHCI Host Controller
[    2.329960] usb usb4: Manufacturer: Linux 2.6.26-2-686 ehci_hcd
[    2.329960] usb usb4: SerialNumber: 0000:00:1a.7
[    2.329960] ACPI: PCI Interrupt 0000:00:1d.0[A] -> GSI 23 (level, low) -> IRQ 23
[    2.329960] PCI: Setting latency timer of device 0000:00:1d.0 to 64
[    2.329960] uhci_hcd 0000:00:1d.0: UHCI Host Controller
[    2.329960] uhci_hcd 0000:00:1d.0: new USB bus registered, assigned bus number 5
[    2.329960] uhci_hcd 0000:00:1d.0: irq 23, io base 0x00001860
[    2.329960] usb usb5: configuration #1 chosen from 1 choice
[    2.329960] hub 5-0:1.0: USB hub found
[    2.329960] hub 5-0:1.0: 2 ports detected
[    2.433386] usb usb5: New USB device found, idVendor=1d6b, idProduct=0001
[    2.433391] usb usb5: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[    2.433394] usb usb5: Product: UHCI Host Controller
[    2.433397] usb usb5: Manufacturer: Linux 2.6.26-2-686 uhci_hcd
[    2.433400] usb usb5: SerialNumber: 0000:00:1d.0
[    2.434763] ACPI: PCI Interrupt 0000:00:1d.1[B] -> GSI 19 (level, low) -> IRQ 19
[    2.434763] PCI: Setting latency timer of device 0000:00:1d.1 to 64
[    2.434763] uhci_hcd 0000:00:1d.1: UHCI Host Controller
[    2.434763] uhci_hcd 0000:00:1d.1: new USB bus registered, assigned bus number 6
[    2.434763] uhci_hcd 0000:00:1d.1: irq 19, io base 0x00001880
[    2.434763] usb usb6: configuration #1 chosen from 1 choice
[    2.434763] hub 6-0:1.0: USB hub found
[    2.434763] hub 6-0:1.0: 2 ports detected
[    2.528718] Clocksource tsc unstable (delta = -472874236 ns)
[    2.537669] usb usb6: New USB device found, idVendor=1d6b, idProduct=0001
[    2.537674] usb usb6: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[    2.537678] usb usb6: Product: UHCI Host Controller
[    2.537681] usb usb6: Manufacturer: Linux 2.6.26-2-686 uhci_hcd
[    2.537684] usb usb6: SerialNumber: 0000:00:1d.1
[    2.538750] ACPI: PCI Interrupt 0000:00:1d.2[C] -> GSI 18 (level, low) -> IRQ 18
[    2.538750] PCI: Setting latency timer of device 0000:00:1d.2 to 64
[    2.538750] uhci_hcd 0000:00:1d.2: UHCI Host Controller
[    2.538750] uhci_hcd 0000:00:1d.2: new USB bus registered, assigned bus number 7
[    2.538750] uhci_hcd 0000:00:1d.2: irq 18, io base 0x000018a0
[    2.538750] usb usb7: configuration #1 chosen from 1 choice
[    2.538750] hub 7-0:1.0: USB hub found
[    2.538750] hub 7-0:1.0: 2 ports detected
[    2.641742] usb usb7: New USB device found, idVendor=1d6b, idProduct=0001
[    2.641746] usb usb7: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[    2.641750] usb usb7: Product: UHCI Host Controller
[    2.641753] usb usb7: Manufacturer: Linux 2.6.26-2-686 uhci_hcd
[    2.641756] usb usb7: SerialNumber: 0000:00:1d.2
[    2.641876] ACPI: PCI Interrupt 0000:00:1d.7[A] -> GSI 23 (level, low) -> IRQ 23
[    2.641876] PCI: Setting latency timer of device 0000:00:1d.7 to 64
[    2.641876] ehci_hcd 0000:00:1d.7: EHCI Host Controller
[    2.641876] ehci_hcd 0000:00:1d.7: new USB bus registered, assigned bus number 8
[    2.642762] ehci_hcd 0000:00:1d.7: debug port 1
[    2.642768] PCI: cache line size of 32 is not supported by device 0000:00:1d.7
[    2.642772] ehci_hcd 0000:00:1d.7: irq 23, io mem 0xf7405c00
[    2.658767] ehci_hcd 0000:00:1d.7: USB 2.0 started, EHCI 1.00, driver 10 Dec 2004
[    2.658844] usb usb8: configuration #1 chosen from 1 choice
[    2.658844] hub 8-0:1.0: USB hub found
[    2.658844] hub 8-0:1.0: 6 ports detected
[    2.762114] usb usb8: New USB device found, idVendor=1d6b, idProduct=0002
[    2.762118] usb usb8: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[    2.762122] usb usb8: Product: EHCI Host Controller
[    2.762125] usb usb8: Manufacturer: Linux 2.6.26-2-686 ehci_hcd
[    2.762128] usb usb8: SerialNumber: 0000:00:1d.7
[    2.763184] ahci 0000:00:1f.2: version 3.0
[    2.763184] ACPI: PCI Interrupt 0000:00:1f.2[B] -> GSI 19 (level, low) -> IRQ 19
[    3.159937] usb 1-1: new full speed USB device using uhci_hcd and address 3
[    3.331873] usb 1-1: configuration #1 chosen from 1 choice
[    3.335074] usb 1-1: New USB device found, idVendor=0a5c, idProduct=2150
[    3.335077] usb 1-1: New USB device strings: Mfr=1, Product=2, SerialNumber=3
[    3.335079] usb 1-1: Product: BCM2046 Bluetooth Device
[    3.335080] usb 1-1: Manufacturer: Broadcom Corp
[    3.335082] usb 1-1: SerialNumber: 00265E9E6742
[    3.759383] usb 8-3: new high speed USB device using ehci_hcd and address 3
[    3.767726] ahci 0000:00:1f.2: AHCI 0001.0200 32 slots 4 ports 3 Gbps 0x13 impl SATA mode
[    3.767732] ahci 0000:00:1f.2: flags: 64bit ncq sntf stag pm led clo pio slum part
[    3.767739] PCI: Setting latency timer of device 0000:00:1f.2 to 64
[    3.769880] scsi0 : ahci
[    3.769880] scsi1 : ahci
[    3.769880] scsi2 : ahci
[    3.769880] scsi3 : ahci
[    3.769880] scsi4 : ahci
[    3.769880] ata1: SATA max UDMA/133 abar m2048@0xf7405000 port 0xf7405100 irq 217
[    3.769880] ata2: SATA max UDMA/133 abar m2048@0xf7405000 port 0xf7405180 irq 217
[    3.769880] ata3: DUMMY
[    3.769880] ata4: DUMMY
[    3.769880] ata5: SATA max UDMA/133 abar m2048@0xf7405000 port 0xf7405300 irq 217
[    4.005378] usb 8-3: configuration #1 chosen from 1 choice
[    4.025703] usb 8-3: New USB device found, idVendor=5986, idProduct=0145
[    4.025703] usb 8-3: New USB device strings: Mfr=3, Product=1, SerialNumber=0
[    4.025703] usb 8-3: Product: Lenovo EasyCamera
[    4.025703] usb 8-3: Manufacturer: Bison Electronics Inc.
[    4.090306] ata1: SATA link up 3.0 Gbps (SStatus 123 SControl 300)
[    4.091757] ata1.00: ATA-8: Hitachi HTS543232L9A300, FB4OC4DC, max UDMA/133
[    4.091757] ata1.00: 625142448 sectors, multi 16: LBA48 NCQ (depth 31/32)
[    4.092279] ata1.00: configured for UDMA/133
[    4.263061] usb 5-1: new low speed USB device using uhci_hcd and address 2
[    4.426423] ata2: SATA link up 1.5 Gbps (SStatus 113 SControl 300)
[    4.430195] ata2.00: ATAPI: HL-DT-ST DVDRAM GSA-T50N, RV06, max UDMA/133
[    4.434654] usb 5-1: configuration #1 chosen from 1 choice
[    4.434954] ata2.00: configured for UDMA/133
[    4.437308] usb 5-1: New USB device found, idVendor=09da, idProduct=000a
[    4.437308] usb 5-1: New USB device strings: Mfr=1, Product=2, SerialNumber=0
[    4.437308] usb 5-1: Product: PS/2+USB Mouse
[    4.437308] usb 5-1: Manufacturer: A4Tech
[    4.453191] usbcore: registered new interface driver hiddev
[    4.462603] input: A4Tech PS/2+USB Mouse as /class/input/input1
[    4.462603] input,hidraw0: USB HID v1.10 Mouse [A4Tech PS/2+USB Mouse] on usb-0000:00:1d.0-1
[    4.462603] usbcore: registered new interface driver usbhid
[    4.462603] usbhid: v2.6:USB HID core driver
[    4.768297] ata5: SATA link down (SStatus 0 SControl 300)
[    4.784396] scsi 0:0:0:0: Direct-Access     ATA      Hitachi HTS54323 FB4O PQ: 0 ANSI: 5
[    4.786438] scsi 1:0:0:0: CD-ROM            HL-DT-ST DVDRAM GSA-T50N  RV06 PQ: 0 ANSI: 5
[    4.788715] tg3.c:v3.92.1 (June 9, 2008)
[    4.788715] ACPI: PCI Interrupt 0000:07:00.0[A] -> GSI 17 (level, low) -> IRQ 17
[    4.788715] PCI: Setting latency timer of device 0000:07:00.0 to 64
[    5.124176] eth0: Tigon3 [partno(BCM95906) rev c002 PHY(5906)] (PCI Express) 10/100Base-TX Ethernet 00:26:22:05:14:a4
[    5.124179] eth0: RXcsums[1] LinkChgREG[0] MIirq[0] ASF[0] WireSpeed[0] TSOcap[0]
[    5.124182] eth0: dma_rwctrl[76180000] dma_mask[64-bit]
[    5.135747] Driver 'sd' needs updating - please use bus_type methods
[    5.135748] sd 0:0:0:0: [sda] 625142448 512-byte hardware sectors (320073 MB)
[    5.135748] sd 0:0:0:0: [sda] Write Protect is off
[    5.135748] sd 0:0:0:0: [sda] Mode Sense: 00 3a 00 00
[    5.135748] sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
[    5.135748] sd 0:0:0:0: [sda] 625142448 512-byte hardware sectors (320073 MB)
[    5.135748] sd 0:0:0:0: [sda] Write Protect is off
[    5.135748] sd 0:0:0:0: [sda] Mode Sense: 00 3a 00 00
[    5.135748] sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
[    5.135748]  sda:<4>Driver 'sr' needs updating - please use bus_type methods
[    5.155537]  sda1 sda2 sda3 sda4
[    5.186041] sd 0:0:0:0: [sda] Attached SCSI disk
[    5.405328] sr0: scsi3-mmc drive: 24x/24x writer dvd-ram cd/rw xa/form2 cdda tray
[    5.405328] Uniform CD-ROM driver Revision: 3.20
[    5.405328] sr 1:0:0:0: Attached scsi CD-ROM sr0
[    5.414196] sd 0:0:0:0: Attached scsi generic sg0 type 0
[    5.414196] sr 1:0:0:0: Attached scsi generic sg1 type 5
[    6.304314] PM: Starting manual resume from disk
[    7.402089] kjournald starting.  Commit interval 5 seconds
[    7.402089] EXT3-fs: mounted filesystem with ordered data mode.
[    9.432339] udevd version 125 started
[   10.005020] Linux agpgart interface v0.103
[   10.036049] input: Power Button (FF) as /class/input/input2
[   10.091800] ACPI: Power Button (FF) [PWRF]
[   10.091853] input: Lid Switch as /class/input/input3
[   10.124700] ACPI: Lid Switch [LID0]
[   10.124747] input: Power Button (CM) as /class/input/input4
[   10.189132] ACPI: Power Button (CM) [PWRB]
[   10.189181] input: Sleep Button (CM) as /class/input/input5
[   10.251881] ACPI: Sleep Button (CM) [SLPB]
[   10.257770] ACPI: device:04 is registered as cooling_device2
[   10.257969] input: Video Bus as /class/input/input6
[   10.315502] ACPI: Video Device [VGA] (multi-head: yes  rom: no  post: no)
[   10.319349] ACPI: device:08 is registered as cooling_device3
[   10.337772] ACPI: device:09 is registered as cooling_device4
[   10.341772] ACPI: device:0a is registered as cooling_device5
[   10.352503] ACPI: device:0b is registered as cooling_device6
[   10.360501] ACPI: device:0c is registered as cooling_device7
[   10.360501] input: Video Bus as /class/input/input7
[   10.422447] ACPI: Video Device [GFX0] (multi-head: yes  rom: no  post: no)
[   10.422407] ACPI: AC Adapter [ACAD] (on-line)
[   10.474338] Bluetooth: Core ver 2.11
[   10.482864] NET: Registered protocol family 31
[   10.482864] Bluetooth: HCI device and connection manager initialized
[   10.482864] Bluetooth: HCI socket layer initialized
[   10.494866] Bluetooth: HCI USB driver ver 2.9
[   10.495214] usbcore: registered new interface driver hci_usb
[   10.564694] ACPI: Battery Slot [BAT1] (battery present)
[   10.825739] input: PC Speaker as /class/input/input8
[   10.863697] ACPI: PCI Interrupt 0000:00:1f.3[C] -> GSI 19 (level, low) -> IRQ 19
[   10.864692] Linux video capture interface: v2.00
[   10.892810] uvcvideo: Found UVC 1.00 device Lenovo EasyCamera (5986:0145)
[   10.897544] input: Lenovo EasyCamera as /class/input/input9
[   10.919877] usbcore: registered new interface driver uvcvideo
[   10.919881] USB Video Class driver (v0.1.0)
[   11.043589] ACPI: PCI Interrupt 0000:00:1b.0[A] -> GSI 22 (level, low) -> IRQ 22
[   11.043614] PCI: Setting latency timer of device 0000:00:1b.0 to 64
[   12.033687] input: PS/2 Mouse as /class/input/input10
[   12.093138] input: AlpsPS/2 ALPS GlidePoint as /class/input/input11
[   12.634715] Adding 7783484k swap on /dev/sda4.  Priority:-1 extents:1 across:7783484k
[   13.145815] EXT3 FS on sda1, internal journal
[   13.499256] loop: module loaded
[  114.146020] kjournald starting.  Commit interval 5 seconds
[  114.146234] EXT3 FS on sda2, internal journal
[  114.146234] EXT3-fs: mounted filesystem with ordered data mode.
[  114.203842] kjournald starting.  Commit interval 5 seconds
[  114.204509] EXT3 FS on sda3, internal journal
[  114.204515] EXT3-fs: mounted filesystem with ordered data mode.
[  117.133267] ACPI: WMI: Mapper loaded
[  117.917721] NET: Registered protocol family 10
[  117.918064] lo: Disabled Privacy Extensions
[  132.819773] ADDRCONF(NETDEV_UP): eth0: link is not ready
[  133.227976] nvidia: module license 'NVIDIA' taints kernel.
[  133.480535] ACPI: PCI Interrupt 0000:01:00.0[A] -> GSI 16 (level, low) -> IRQ 16
[  133.480547] PCI: Setting latency timer of device 0000:01:00.0 to 64
[  133.480675] NVRM: loading NVIDIA UNIX x86 Kernel Module  173.14.09  Wed Jun  4 23:43:17 PDT 2008
[  134.473641] tg3: eth0: Link is up at 100 Mbps, full duplex.
[  134.473641] tg3: eth0: Flow control is on for TX and on for RX.
[  135.369643] ADDRCONF(NETDEV_CHANGE): eth0: link becomes ready
[  135.950973] ADDRCONF(NETDEV_UP): eth0: link is not ready
[  137.521977] tg3: eth0: Link is up at 100 Mbps, full duplex.
[  137.521977] tg3: eth0: Flow control is on for TX and on for RX.
[  137.521977] ADDRCONF(NETDEV_CHANGE): eth0: link becomes ready
[  147.832106] eth0: no IPv6 routers present
[  161.206705] CPU0 attaching NULL sched-domain.
[  161.206711] CPU1 attaching NULL sched-domain.
[  161.214673] CPU0 attaching sched-domain:
[  161.214673]  domain 0: span 0-1
[  161.214673]   groups: 0 1
[  161.214673] CPU1 attaching sched-domain:
[  161.214673]  domain 0: span 0-1
[  161.214673]   groups: 1 0

Kod: Zaznacz cały

lenny kernel 2.6.26-2-686
Po zainstalowaniu pakietu firmware-iwlwifi i restarcie nic się nie zmieniło. Nadal nie wykrywa karty.

sidjestgit
Beginner
Posty: 181
Rejestracja: 06 grudnia 2008, 17:55

Post autor: sidjestgit » 19 listopada 2009, 21:45

Zainstaluj kernel z backortow.
dodaj do /etc/apt/sources.list taki wpis

Kod: Zaznacz cały

deb [url]http://www.backports.org/debian[/url] lenny-backports main contrib non-free
nastepnie

Kod: Zaznacz cały

su
apt-get update
apt-cache search linux-image
apt-get install nazwa_kernela_jaki_wybrales np:

Kod: Zaznacz cały

apt-get install linux-image-2.6.30-bpo.2-686
odinstaluj stary pakiet firmware-iwlwifi

Kod: Zaznacz cały

apt-get remove --purge firmware-iwlwifi
Restart systemu - uruchom system na nowym kernelu.

sciagnij i zainstaluj nowsza wersje firmware-iwlwifi

Kod: Zaznacz cały

wget [url]http://www.backports.org/debian/pool/non-free/f/firmware-nonfree/firmware-iwlwifi_0.17~bpo50+1_all.deb[/url]

Kod: Zaznacz cały

dpkg -i firmware-iwlwifi_0.17~bpo50+1_all.deb

Kod: Zaznacz cały

ifconfig wlan0 up
uruchom wicd - i polacz sie z siecia.

szcz00ri
Posty: 13
Rejestracja: 05 sierpnia 2009, 09:33
Lokalizacja: Inowrocław

Post autor: szcz00ri » 19 listopada 2009, 23:06

Dobra sprawa wlan rozwiązana, ale po instalacji nowego jądra X-y mi nie wstały.

Doinstalowałem headers i podczas instalacji wyskoczyła mi informacja

Kod: Zaznacz cały

No precompiled kernel interface was found to match your kernel; this means that the installer will need to compilke a new kernel interface.
Następne okienko:

Kod: Zaznacz cały

Depending on where and how the kernel sources (or the kernel headers) were installed, you may need to specify their location with the SYSSRC environment variable or the equivalent nvidia-installer command line option.
Na sterowniku Vesa działa.

Jakieś propozycje?

fnmirk
Senior Member
Posty: 8037
Rejestracja: 03 grudnia 2007, 06:37

Post autor: fnmirk » 20 listopada 2009, 06:59

szcz00ri pisze:Na sterowniku Vesa działa.
Potrzebna instalacja sterowników karty graficzne.

szcz00ri
Posty: 13
Rejestracja: 05 sierpnia 2009, 09:33
Lokalizacja: Inowrocław

Post autor: szcz00ri » 20 listopada 2009, 07:05

Też tak myślę, ale z jakiegoś powodu nie chcą się zainstalować. Na starym kernelu korzystając z tego poradnika HOWTO wszystko poszło bez problemów.

Sterownik

Kod: Zaznacz cały

NVIDIA-Linux-x86-173.14.09-pkg1.run
Błędy jakie się pokazują podczas instalacji napisałem w poście wyżej.

edit

Poradziłem sobie. Zainstalowałem najnowszy sterownik.

Kod: Zaznacz cały

NVIDIA-Linux-x86-190.42-pkg1.run
Dziękuję wszystkim za pomoc.

[ Dodano: |20 Lis 2009|, 2009 11:12 ]
Jeden problem zniknął to następny się pojawił.

Hibernacja przestała mi działać. Laptop się hibernuje, ale po wybudzeniu dochodzi do 100% i pojawia się czarny ekran.

Gdzieś na forum przeczytałem, że trzeba zakomentować "nvidia" w

Kod: Zaznacz cały

/etc/hibernate/blacklisted-modules
. Nie pomogło.

kuba_astr
Posty: 12
Rejestracja: 09 stycznia 2008, 13:56

Post autor: kuba_astr » 14 grudnia 2009, 19:01

Przepraszam, że tak z buta bez przywitania się wtrącę w wątek ale nigdzie (absolutnie nigdzie) w sieci nie ma informacji na temat konfiguracji i 5100 pod jądrem 2.6.26.
Rozumiem, że najprostszym rozwiązaniem jest instalacja nowego jajca ale cóż... Nie wchodzi to w grę. Mam laptopa Lenovo t400 i przy jądrach wyższych niż 2.6.26 wywala mi całkowicie ACPI (nie działa BT, i skróty klawiszowe FN+...)
Jest to jakaś masakra!
Mogę mieć wifi i pół-system, lub stabilny system i brak wifi.

Może macie jakieś sugestie, najlepiej jak dodać sterowniki do 5100 do jądra 2.6.26.

Kod: Zaznacz cały

debian:/home/kuba/Desktop# modprobe iwlagn
FATAL: Module iwlagn not found.
debian:/home/kuba/Desktop# modprobe iwlwifi
FATAL: Module iwlwifi not found.
debian:/home/kuba/Desktop#
Pozdrawiam
Kuba

Awatar użytkownika
iria
Junior Member
Posty: 941
Rejestracja: 04 czerwca 2007, 18:54

Post autor: iria » 14 grudnia 2009, 19:51

Spróbowałeś, po prostu zainstalować paczkę z firmware do kart Intela, np. ze Squeeze?

kuba_astr
Posty: 12
Rejestracja: 09 stycznia 2008, 13:56

Post autor: kuba_astr » 14 grudnia 2009, 20:39

Iria: nie za bardzo, próbowałem coś wykombinowac z dograniem firmware'u z intellinux.... Ale to chyba na nic...

ODPOWIEDZ