Interfejs sieciowy nie podnosi sie podczas startu

Masz problemy z siecią bądź internetem? Zapytaj tu
Globals
Posty: 53
Rejestracja: 21 maja 2011, 21:00

Interfejs sieciowy nie podnosi sie podczas startu

Post autor: Globals » 21 stycznia 2014, 07:56

Witam
Mam taki problem interfejs sieciowy eth0 nie chce się podnieść podczas startu komputera.Dopiero po wydaniu polecenia dhclient eth0 wstaje.
Plik /etc/network/interfaces:

Kod: Zaznacz cały

This file describes the network interfaces available on your system
# and how to activate them. For more information, see interfaces(5).

# The loopback network interface
auto lo
iface lo inet loopback

# The primary network interface
auto eth0
iface eth0 inet dhcp
dodam jeszcze że jak wchodzę do katalogu /etc/network to mam plik !run na czerwono

Van Pytel
Beginner
Posty: 166
Rejestracja: 09 maja 2010, 17:05

Post autor: Van Pytel » 21 stycznia 2014, 08:46

! oznacza, żę jest źle podlinkowany. Dowiązanie powinno być do: /run/network/

Globals
Posty: 53
Rejestracja: 21 maja 2011, 21:00

Post autor: Globals » 21 stycznia 2014, 09:54

ale jak wchodzę do katalogu /run to nie mam /network

Awatar użytkownika
pone13
Beginner
Posty: 337
Rejestracja: 30 listopada 2007, 20:59
Lokalizacja: Leszno

Post autor: pone13 » 21 stycznia 2014, 10:16

To go utwórz i ewentualnie popraw dowiązanie /etc/network/run -> /run/network - sprawdź po stworzeniu katalogu /run/network poleceniem ls
czy wspomniane dowiązanie nie jest już poprawne.

Globals
Posty: 53
Rejestracja: 21 maja 2011, 21:00

Post autor: Globals » 21 stycznia 2014, 10:52

No dobra po utworzeniu katalogu network nie ma już wykrzyknika w /etc/network ale później jeszcze uruchomię maszynę i zobaczymy czy interfejs wstanie

Globals
Posty: 53
Rejestracja: 21 maja 2011, 21:00

Post autor: Globals » 21 stycznia 2014, 15:07

uruchomiłem komputer ponownie i interfejs się nie podniósł podczas startu wszedłem w katalog /run a tam nie był już network

Awatar użytkownika
pone13
Beginner
Posty: 337
Rejestracja: 30 listopada 2007, 20:59
Lokalizacja: Leszno

Post autor: pone13 » 22 stycznia 2014, 07:42

Masz uszkodzone lub brak zainstalowanych skryptów startowych dla sieci.
Co to za system, czy korzystasz z jakiegoś środowiska graficznego (menedżer sieci środowiska graficznego może
zmieniać ustawienia sieci podczas startu)?.
Jeżeli nie korzystasz z menedżera sieci sprawdź czy masz skrypt /etc/init.d/networking i czy jest on wykonywany
przy starcie systemu (ma dowiązania w odpowiednich katalogach /etc/rc*):

Kod: Zaznacz cały

grep networking /etc/rc*/*

Globals
Posty: 53
Rejestracja: 21 maja 2011, 21:00

Post autor: Globals » 22 stycznia 2014, 08:35

Nie nie korzystam żadnego środowiska graficznego. Jest skrypt /etc/init.d/networking posiada prawa root 755.Wydałem też polecenie

Kod: Zaznacz cały

grep networking /etc/rc*/*
i o to wynik

Kod: Zaznacz cały

/etc/rc0.d/K06networking:# Provides:          networking ifupdown
/etc/rc0.d/K06networking:[ -f /etc/default/networking ] && . /etc/default/networking
/etc/rc0.d/K06networking:           log_action_msg "Not configuring network interfaces, see /etc/default/networking"
/etc/rc0.d/K06networking:       echo "Usage: /etc/init.d/networking {start|stop|reload|restart|force-reload}"
/etc/rc6.d/K06networking:# Provides:          networking ifupdown
/etc/rc6.d/K06networking:[ -f /etc/default/networking ] && . /etc/default/networking
/etc/rc6.d/K06networking:           log_action_msg "Not configuring network interfaces, see /etc/default/networking"
/etc/rc6.d/K06networking:       echo "Usage: /etc/init.d/networking {start|stop|reload|restart|force-reload}"
/etc/rcS.d/S12ifupdown:    log_begin_msg "Setting up networking..."
/etc/rcS.d/S13networking:# Provides:          networking ifupdown
/etc/rcS.d/S13networking:[ -f /etc/default/networking ] && . /etc/default/networking
/etc/rcS.d/S13networking:           log_action_msg "Not configuring network interfaces, see /etc/default/networking"
/etc/rcS.d/S13networking:       echo "Usage: /etc/init.d/networking {start|stop|reload|restart|force-reload}"

Awatar użytkownika
pone13
Beginner
Posty: 337
Rejestracja: 30 listopada 2007, 20:59
Lokalizacja: Leszno

Post autor: pone13 » 22 stycznia 2014, 14:53

Żeby rozwiązać twój problem będzie potrzebne więcej informacji, podaj wyniki:

Kod: Zaznacz cały

$ lspci
oraz

Kod: Zaznacz cały

$ dmesg
i na koniec

Kod: Zaznacz cały

# cat /var/log/syslog | grep eth0

Globals
Posty: 53
Rejestracja: 21 maja 2011, 21:00

Post autor: Globals » 22 stycznia 2014, 16:46

wyniki
lspci

Kod: Zaznacz cały

00:00.0 Host bridge: Intel Corporation 4 Series Chipset DRAM Controller (rev 03)
00:02.0 VGA compatible controller: Intel Corporation 4 Series Chipset Integrated Graphics Controller (rev 03)
00:1c.0 PCI bridge: Intel Corporation NM10/ICH7 Family PCI Express Port 1 (rev 01)
00:1d.0 USB controller: Intel Corporation NM10/ICH7 Family USB UHCI Controller #1 (rev 01)
00:1d.1 USB controller: Intel Corporation NM10/ICH7 Family USB UHCI Controller #2 (rev 01)
00:1d.2 USB controller: Intel Corporation NM10/ICH7 Family USB UHCI Controller #3 (rev 01)
00:1d.3 USB controller: Intel Corporation NM10/ICH7 Family USB UHCI Controller #4 (rev 01)
00:1d.7 USB controller: Intel Corporation NM10/ICH7 Family USB2 EHCI Controller(rev 01)
00:1e.0 PCI bridge: Intel Corporation 82801 PCI Bridge (rev e1)
00:1f.0 ISA bridge: Intel Corporation 82801GB/GR (ICH7 Family) LPC Interface Bridge (rev 01)
00:1f.1 IDE interface: Intel Corporation 82801G (ICH7 Family) IDE Controller (rev 01)
00:1f.2 IDE interface: Intel Corporation NM10/ICH7 Family SATA Controller [IDE mode] (rev 01)
02:01.0 Ethernet controller: Intel Corporation 82541PI Gigabit Ethernet Controller (rev 05)
cat /var/log/syslog | grep eth0

Kod: Zaznacz cały

Jan 22 15:03:01 nnd kernel: [    1.290307] e1000 0000:02:01.0: eth0: (PCI:33MHz32-bit) 00:1b:21:82:74:b3
Jan 22 15:03:01 nnd kernel: [    1.290310] e1000 0000:02:01.0: eth0: Intel(R) PRO/1000 Network Connection
Jan 22 15:06:17 nnd kernel: [    1.294329] e1000 0000:02:01.0: eth0: (PCI:33MHz:32-bit) 00:1b:21:82:74:b3
Jan 22 15:06:17 nnd kernel: [    1.294332] e1000 0000:02:01.0: eth0: Intel(R) PRO/1000 Network Connection
Jan 22 15:07:34 nnd kernel: [    1.314477] e1000 0000:02:01.0: eth0: (PCI:33MHz32-bit) 00:1b:21:82:74:b3
Jan 22 15:07:34 nnd kernel: [    1.314480] e1000 0000:02:01.0: eth0: Intel(R) PRO/1000 Network Connection
Jan 22 15:08:09 nnd kernel: [   43.689371] ADDRCONF(NETDEV_UP): eth0: link is not ready
Jan 22 15:08:09 nnd kernel: [   43.693403] e1000: eth0 NIC Link is Up 1000 MbpsFull Duplex, Flow Control: RX
Jan 22 15:08:09 nnd kernel: [   43.693587] ADDRCONF(NETDEV_CHANGE): eth0: link becomes ready
Jan 22 15:08:09 nnd dhclient: DHCPREQUEST on eth0 to 255.255.255.255 port 6
dmesg

Kod: Zaznacz cały

[    0.000000] Initializing cgroup subsys cpuset
[    0.000000] Initializing cgroup subsys cpu
[    0.000000] Linux version 3.2.0-4-686-pae (debian-kernel@lists.debian.org) (gcc version 4.6.3 (Debian 4.6.3-14) ) #1 SMP Debian 3.2.51-1
[    0.000000] BIOS-provided physical RAM map:
[    0.000000]  BIOS-e820: 0000000000000000 - 000000000009fc00 (usable)
[    0.000000]  BIOS-e820: 000000000009fc00 - 00000000000a0000 (reserved)
[    0.000000]  BIOS-e820: 00000000000e4000 - 0000000000100000 (reserved)
[    0.000000]  BIOS-e820: 0000000000100000 - 00000000ddd80000 (usable)
[    0.000000]  BIOS-e820: 00000000ddd80000 - 00000000ddd8e000 (ACPI data)
[    0.000000]  BIOS-e820: 00000000ddd8e000 - 00000000dddd0000 (ACPI NVS)
[    0.000000]  BIOS-e820: 00000000dddd0000 - 00000000e0000000 (reserved)
[    0.000000]  BIOS-e820: 00000000fee00000 - 00000000fee01000 (reserved)
[    0.000000]  BIOS-e820: 00000000fff00000 - 0000000100000000 (reserved)
[    0.000000]  BIOS-e820: 0000000100000000 - 0000000120000000 (usable)
[    0.000000] NX (Execute Disable) protection: active
[    0.000000] SMBIOS 2.5 present.
[    0.000000] DMI: System manufacturer System Product Name/P5G41T-M LX3, BIOS 0503    08/09/2012
[    0.000000] e820 update range: 0000000000000000 - 0000000000010000 (usable) ==> (reserved)
[    0.000000] e820 remove range: 00000000000a0000 - 0000000000100000 (usable)
[    0.000000] last_pfn = 0x120000 max_arch_pfn = 0x1000000
[    0.000000] MTRR default type: uncachable
[    0.000000] MTRR fixed ranges enabled:
[    0.000000]   00000-9FFFF write-back
[    0.000000]   A0000-BFFFF uncachable
[    0.000000]   C0000-CFFFF write-protect
[    0.000000]   D0000-DFFFF uncachable
[    0.000000]   E0000-EFFFF write-through
[    0.000000]   F0000-FFFFF write-protect
[    0.000000] MTRR variable ranges enabled:
[    0.000000]   0 base 000000000 mask F00000000 write-back
[    0.000000]   1 base 100000000 mask FE0000000 write-back
[    0.000000]   2 base 0E0000000 mask FE0000000 uncachable
[    0.000000]   3 base 0DDE00000 mask FFFE00000 uncachable
[    0.000000]   4 base 0DE000000 mask FFE000000 uncachable
[    0.000000]   5 disabled
[    0.000000]   6 disabled
[    0.000000]   7 disabled
[    0.000000] x86 PAT enabled: cpu 0, old 0x7040600070406, new 0x7010600070106
[    0.000000] e820 update range: 00000000dde00000 - 0000000100000000 (usable) ==> (reserved)
[    0.000000] found SMP MP-table at [c00ff780] ff780
[    0.000000] initial memory mapped : 0 - 01a00000
[    0.000000] Base memory trampoline at [c009b000] 9b000 size 16384
[    0.000000] init_memory_mapping: 0000000000000000-00000000379fe000
[    0.000000]  0000000000 - 0000200000 page 4k
[    0.000000]  0000200000 - 0037800000 page 2M
[    0.000000]  0037800000 - 00379fe000 page 4k
[    0.000000] kernel direct mapping tables up to 379fe000 @ 19f9000-1a00000
[    0.000000] RAMDISK: 36d18000 - 37684000
[    0.000000] ACPI: RSDP 000fbd40 00024 (v02 ACPIAM)
[    0.000000] ACPI: XSDT ddd80100 00054 (v01 A_M_I_ OEMXSDT  08001209 MSFT 00000097)
[    0.000000] ACPI: FACP ddd80290 000F4 (v03 A_M_I_ OEMFACP  08001209 MSFT 00000097)
[    0.000000] ACPI: DSDT ddd80440 07AFD (v01  A1788 A1788000 00000000 INTL 20060113)
[    0.000000] ACPI: FACS ddd8e000 00040
[    0.000000] ACPI: APIC ddd80390 0006C (v01 A_M_I_ OEMAPIC  08001209 MSFT 00000097)
[    0.000000] ACPI: MCFG ddd80400 0003C (v01 A_M_I_ OEMMCFG  08001209 MSFT 00000097)
[    0.000000] ACPI: OEMB ddd8e040 00089 (v01 A_M_I_ AMI_OEM  08001209 MSFT 00000097)
[    0.000000] ACPI: HPET ddd87f40 00038 (v01 A_M_I_ OEMHPET  08001209 MSFT 00000097)
[    0.000000] ACPI: GSCI ddd8e0d0 02024 (v01 A_M_I_ GMCHSCI  08001209 MSFT 00000097)
[    0.000000] ACPI: Local APIC address 0xfee00000
[    0.000000] 3718MB HIGHMEM available.
[    0.000000] 889MB LOWMEM available.
[    0.000000]   mapped low ram: 0 - 379fe000
[    0.000000]   low ram: 0 - 379fe000
[    0.000000] Zone PFN ranges:
[    0.000000]   DMA      0x00000010 -> 0x00001000
[    0.000000]   Normal   0x00001000 -> 0x000379fe
[    0.000000]   HighMem  0x000379fe -> 0x00120000
[    0.000000] Movable zone start PFN for each node
[    0.000000] early_node_map[3] active PFN ranges
[    0.000000]     0: 0x00000010 -> 0x0000009f
[    0.000000]     0: 0x00000100 -> 0x000ddd80
[    0.000000]     0: 0x00100000 -> 0x00120000
[    0.000000] On node 0 totalpages: 1039631
[    0.000000] free_area_init_node: node 0, pgdat c1412740, node_mem_map f4918200
[    0.000000]   DMA zone: 32 pages used for memmap
[    0.000000]   DMA zone: 0 pages reserved
[    0.000000]   DMA zone: 3951 pages, LIFO batch:0
[    0.000000]   Normal zone: 1748 pages used for memmap
[    0.000000]   Normal zone: 221994 pages, LIFO batch:31
[    0.000000]   HighMem zone: 7437 pages used for memmap
[    0.000000]   HighMem zone: 804469 pages, LIFO batch:31
[    0.000000] Using APIC driver default
[    0.000000] ACPI: PM-Timer IO Port: 0x808
[    0.000000] ACPI: Local APIC address 0xfee00000
[    0.000000] ACPI: LAPIC (acpi_id[0x01] lapic_id[0x00] enabled)
[    0.000000] ACPI: LAPIC (acpi_id[0x02] lapic_id[0x01] enabled)
[    0.000000] ACPI: LAPIC (acpi_id[0x03] lapic_id[0x82] disabled)
[    0.000000] ACPI: LAPIC (acpi_id[0x04] lapic_id[0x83] disabled)
[    0.000000] ACPI: IOAPIC (id[0x02] address[0xfec00000] gsi_base[0])
[    0.000000] IOAPIC[0]: apic_id 2, version 32, address 0xfec00000, GSI 0-23
[    0.000000] ACPI: INT_SRC_OVR (bus 0 bus_irq 0 global_irq 2 dfl dfl)
[    0.000000] ACPI: INT_SRC_OVR (bus 0 bus_irq 9 global_irq 9 high level)
[    0.000000] ACPI: IRQ0 used by override.
[    0.000000] ACPI: IRQ2 used by override.
[    0.000000] ACPI: IRQ9 used by override.
[    0.000000] Using ACPI (MADT) for SMP configuration information
[    0.000000] ACPI: HPET id: 0x8086a201 base: 0xfed00000
[    0.000000] SMP: Allowing 4 CPUs, 2 hotplug CPUs
[    0.000000] nr_irqs_gsi: 40
[    0.000000] PM: Registered nosave memory: 000000000009f000 - 00000000000a0000
[    0.000000] PM: Registered nosave memory: 00000000000a0000 - 00000000000e4000
[    0.000000] PM: Registered nosave memory: 00000000000e4000 - 0000000000100000
[    0.000000] Allocating PCI resources starting at e0000000 (gap: e0000000:1ee00000)
[    0.000000] Booting paravirtualized kernel on bare hardware
[    0.000000] setup_percpu: NR_CPUS:32 nr_cpumask_bits:32 nr_cpu_ids:4 nr_node_ids:1
[    0.000000] PERCPU: Embedded 14 pages/cpu @f79b3000 s33280 r0 d24064 u57344
[    0.000000] pcpu-alloc: s33280 r0 d24064 u57344 alloc=14*4096
[    0.000000] pcpu-alloc: [0] 0 [0] 1 [0] 2 [0] 3
[    0.000000] Built 1 zonelists in Zone order, mobility grouping on.  Total pages: 1030414
[    0.000000] Kernel command line: BOOT_IMAGE=/boot/vmlinuz-3.2.0-4-686-pae root=UUID=b5f56152-12bb-4b2e-8e1f-4964b8e35d6e ro quiet
[    0.000000] PID hash table entries: 4096 (order: 2, 16384 bytes)
[    0.000000] Dentry cache hash table entries: 131072 (order: 7, 524288 bytes)
[    0.000000] Inode-cache hash table entries: 65536 (order: 6, 262144 bytes)
[    0.000000] Initializing CPU#0
[    0.000000] xsave/xrstor: enabled xstate_bv 0x3, cntxt size 0x240
[    0.000000] Initializing HighMem for node 0 (000379fe:00120000)
[    0.000000] Memory: 4105684k/4718592k available (2852k kernel code, 52840k reserved, 1347k data, 416k init, 3247624k highmem)
[    0.000000] virtual kernel memory layout:
[    0.000000]     fixmap  : 0xffd36000 - 0xfffff000   (2852 kB)
[    0.000000]     pkmap   : 0xffa00000 - 0xffc00000   (2048 kB)
[    0.000000]     vmalloc : 0xf81fe000 - 0xff9fe000   ( 120 MB)
[    0.000000]     lowmem  : 0xc0000000 - 0xf79fe000   ( 889 MB)
[    0.000000]       .init : 0xc141b000 - 0xc1483000   ( 416 kB)
[    0.000000]       .data : 0xc12c93c0 - 0xc141a100   (1347 kB)
[    0.000000]       .text : 0xc1000000 - 0xc12c93c0   (2852 kB)
[    0.000000] Checking if this processor honours the WP bit even in supervisor mode...Ok.
[    0.000000] Hierarchical RCU implementation.
[    0.000000]  RCU dyntick-idle grace-period acceleration is enabled.
[    0.000000] NR_IRQS:2304 nr_irqs:712 16
[    0.000000] CPU 0 irqstacks, hard=f4406000 soft=f4408000
[    0.000000] Extended CMOS year: 2000
[    0.000000] Console: colour VGA+ 80x25
[    0.000000] console [tty0] enabled
[    0.000000] hpet clockevent registered
[    0.000000] Fast TSC calibration using PIT
[    0.000000] Detected 3001.070 MHz processor.
[    0.004001] Calibrating delay loop (skipped), value calculated using timer frequency.. 6002.14 BogoMIPS (lpj=12004280)
[    0.004005] pid_max: default: 32768 minimum: 301
[    0.004030] Security Framework initialized
[    0.004034] AppArmor: AppArmor disabled by boot time parameter
[    0.004045] Mount-cache hash table entries: 512
[    0.004137] Initializing cgroup subsys cpuacct
[    0.004141] Initializing cgroup subsys memory
[    0.004147] Initializing cgroup subsys devices
[    0.004149] Initializing cgroup subsys freezer
[    0.004150] Initializing cgroup subsys net_cls
[    0.004152] Initializing cgroup subsys blkio
[    0.004156] Initializing cgroup subsys perf_event
[    0.004178] CPU: Physical Processor ID: 0
[    0.004179] CPU: Processor Core ID: 0
[    0.004182] mce: CPU supports 6 MCE banks
[    0.004188] CPU0: Thermal monitoring enabled (TM2)
[    0.004191] using mwait in idle threads.
[    0.004502] ACPI: Core revision 20110623
[    0.008605] Enabling APIC mode:  Flat.  Using 1 I/O APICs
[    0.008953] ..TIMER: vector=0x30 apic1=0 pin1=2 apic2=-1 pin2=-1
[    0.048646] CPU0: Intel(R) Core(TM)2 Duo CPU     E8400  @ 3.00GHz stepping 0a
[    0.052002] Performance Events: PEBS fmt0+, Core2 events, Intel PMU driver.
[    0.052002] ... version:                2
[    0.052002] ... bit width:              40
[    0.052002] ... generic registers:      2
[    0.052002] ... value mask:             000000ffffffffff
[    0.052002] ... max period:             000000007fffffff
[    0.052002] ... fixed-purpose events:   3
[    0.052002] ... event mask:             0000000700000003
[    0.052002] NMI watchdog enabled, takes one hw-pmu counter.
[    0.052002] CPU 1 irqstacks, hard=f44d4000 soft=f44d6000
[    0.052002] Booting Node   0, Processors  #1
[    0.052002] smpboot cpu 1: start_ip = 9b000
[    0.008000] Initializing CPU#1
[    0.140031] NMI watchdog enabled, takes one hw-pmu counter.
[    0.140057] Brought up 2 CPUs
[    0.140059] Total of 2 processors activated (12003.81 BogoMIPS).
[    0.142644] devtmpfs: initialized
[    0.142644] PM: Registering ACPI NVS region at ddd8e000 (270336 bytes)
[    0.142644] print_constraints: dummy:
[    0.142644] NET: Registered protocol family 16
[    0.142644] ACPI: bus type pci registered
[    0.142644] PCI: MMCONFIG for domain 0000 [bus 00-3f] at [mem 0xf0000000-0xf3ffffff] (base 0xf0000000)
[    0.142644] PCI: not using MMCONFIG
[    0.142644] PCI : PCI BIOS aera is rw and x. Use pci=nobios if you want it NX.
[    0.142644] PCI: PCI BIOS revision 3.00 entry at 0xf0031, last bus=2
[    0.142644] PCI: Using configuration type 1 for base access
[    0.142644] bio: create slab <bio-0> at 0
[    0.142644] ACPI: Added _OSI(Module Device)
[    0.142644] ACPI: Added _OSI(Processor Device)
[    0.142644] ACPI: Added _OSI(3.0 _SCP Extensions)
[    0.142644] ACPI: Added _OSI(Processor Aggregator Device)
[    0.144701] ACPI: EC: Look up EC in DSDT
[    0.145487] ACPI: Executed 1 blocks of module-level executable AML code
[    0.148364] ACPI: Interpreter enabled
[    0.148375] ACPI: (supports S0 S1 S3 S4 S5)
[    0.148393] ACPI: Using IOAPIC for interrupt routing
[    0.148410] PCI: MMCONFIG for domain 0000 [bus 00-3f] at [mem 0xf0000000-0xf3ffffff] (base 0xf0000000)
[    0.149153] PCI: MMCONFIG at [mem 0xf0000000-0xf3ffffff] reserved in ACPI motherboard resources
[    0.149154] PCI: Using MMCONFIG for extended config space
[    0.152981] ACPI: No dock devices found.
[    0.152983] HEST: Table not found.
[    0.152986] PCI: Using host bridge windows from ACPI; if necessary, use "pci=nocrs" and report a bug
[    0.153048] ACPI: PCI Root Bridge [PCI0] (domain 0000 [bus 00-ff])
[    0.153176] pci_root PNP0A08:00: host bridge window [io  0x0000-0x0cf7]
[    0.153179] pci_root PNP0A08:00: host bridge window [io  0x0d00-0xffff]
[    0.153181] pci_root PNP0A08:00: host bridge window [mem 0x000a0000-0x000bffff]
[    0.153183] pci_root PNP0A08:00: host bridge window [mem 0x000d0000-0x000dffff]
[    0.153185] pci_root PNP0A08:00: host bridge window [mem 0xdde00000-0xefffffff]
[    0.153186] pci_root PNP0A08:00: host bridge window [mem 0xf4000000-0xffffffff]
[    0.153196] pci 0000:00:00.0: [8086:2e30] type 0 class 0x000600
[    0.153228] pci 0000:00:02.0: [8086:2e32] type 0 class 0x000300
[    0.153237] pci 0000:00:02.0: reg 10: [mem 0xfe400000-0xfe7fffff 64bit]
[    0.153243] pci 0000:00:02.0: reg 18: [mem 0xe0000000-0xefffffff 64bit pref]
[    0.153247] pci 0000:00:02.0: reg 20: [io  0xdc00-0xdc07]
[    0.153295] pci 0000:00:1c.0: [8086:27d0] type 1 class 0x000604
[    0.153351] pci 0000:00:1c.0: PME# supported from D0 D3hot D3cold
[    0.153373] pci 0000:00:1d.0: [8086:27c8] type 0 class 0x000c03
[    0.153405] pci 0000:00:1d.0: reg 20: [io  0xd400-0xd41f]
[    0.153431] pci 0000:00:1d.1: [8086:27c9] type 0 class 0x000c03
[    0.153463] pci 0000:00:1d.1: reg 20: [io  0xd480-0xd49f]
[    0.153490] pci 0000:00:1d.2: [8086:27ca] type 0 class 0x000c03
[    0.153522] pci 0000:00:1d.2: reg 20: [io  0xd800-0xd81f]
[    0.153547] pci 0000:00:1d.3: [8086:27cb] type 0 class 0x000c03
[    0.153580] pci 0000:00:1d.3: reg 20: [io  0xd880-0xd89f]
[    0.153612] pci 0000:00:1d.7: [8086:27cc] type 0 class 0x000c03
[    0.153628] pci 0000:00:1d.7: reg 10: [mem 0xfeafbc00-0xfeafbfff]
[    0.153696] pci 0000:00:1d.7: PME# supported from D0 D3hot D3cold
[    0.153712] pci 0000:00:1e.0: [8086:244e] type 1 class 0x000604
[    0.153762] pci 0000:00:1f.0: [8086:27b8] type 0 class 0x000601
[    0.153832] pci 0000:00:1f.0: ICH7 LPC Generic IO decode 1 PIO at 0294 (mask 0003)
[    0.153869] pci 0000:00:1f.1: [8086:27df] type 0 class 0x000101
[    0.153879] pci 0000:00:1f.1: reg 10: [io  0x0000-0x0007]
[    0.153886] pci 0000:00:1f.1: reg 14: [io  0x0000-0x0003]
[    0.153894] pci 0000:00:1f.1: reg 18: [io  0x08f0-0x08f7]
[    0.153901] pci 0000:00:1f.1: reg 1c: [io  0x08f8-0x08fb]
[    0.153909] pci 0000:00:1f.1: reg 20: [io  0xffa0-0xffaf]
[    0.153937] pci 0000:00:1f.2: [8086:27c0] type 0 class 0x000101
[    0.153948] pci 0000:00:1f.2: reg 10: [io  0xd080-0xd087]
[    0.153955] pci 0000:00:1f.2: reg 14: [io  0xd000-0xd003]
[    0.153961] pci 0000:00:1f.2: reg 18: [io  0xcc00-0xcc07]
[    0.153968] pci 0000:00:1f.2: reg 1c: [io  0xc880-0xc883]
[    0.153974] pci 0000:00:1f.2: reg 20: [io  0xc800-0xc80f]
[    0.154002] pci 0000:00:1f.2: PME# supported from D3hot
[    0.154041] pci 0000:00:1c.0: PCI bridge to [bus 01-01]
[    0.154076] pci 0000:02:01.0: [8086:107c] type 0 class 0x000200
[    0.154093] pci 0000:02:01.0: reg 10: [mem 0xfebe0000-0xfebfffff]
[    0.154101] pci 0000:02:01.0: reg 14: [mem 0xfebc0000-0xfebdffff]
[    0.154110] pci 0000:02:01.0: reg 18: [io  0xec00-0xec3f]
[    0.154139] pci 0000:02:01.0: reg 30: [mem 0xfeba0000-0xfebbffff pref]
[    0.154171] pci 0000:02:01.0: PME# supported from D0 D3hot D3cold
[    0.154211] pci 0000:00:1e.0: PCI bridge to [bus 02-02] (subtractive decode)
[    0.154215] pci 0000:00:1e.0:   bridge window [io  0xe000-0xefff]
[    0.154218] pci 0000:00:1e.0:   bridge window [mem 0xfeb00000-0xfebfffff]
[    0.154222] pci 0000:00:1e.0:   bridge window [io  0x0000-0x0cf7] (subtractive decode)
[    0.154224] pci 0000:00:1e.0:   bridge window [io  0x0d00-0xffff] (subtractive decode)
[    0.154226] pci 0000:00:1e.0:   bridge window [mem 0x000a0000-0x000bffff] (subtractive decode)
[    0.154228] pci 0000:00:1e.0:   bridge window [mem 0x000d0000-0x000dffff] (subtractive decode)
[    0.154230] pci 0000:00:1e.0:   bridge window [mem 0xdde00000-0xefffffff] (subtractive decode)
[    0.154232] pci 0000:00:1e.0:   bridge window [mem 0xf4000000-0xffffffff] (subtractive decode)
[    0.154241] pci_bus 0000:00: on NUMA node 0
[    0.154243] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0._PRT]
[    0.154356] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.P0P1._PRT]
[    0.154406] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.P0P4._PRT]
[    0.154445]  pci0000:00: Requesting ACPI _OSC control (0x1d)
[    0.154447]  pci0000:00: ACPI _OSC request failed (AE_NOT_FOUND), returned control mask: 0x1d
[    0.154449] ACPI _OSC control for PCIe not granted, disabling ASPM
[    0.157764] ACPI: PCI Interrupt Link [LNKA] (IRQs 3 4 5 6 7 *10 12 14 15)
[    0.157800] ACPI: PCI Interrupt Link [LNKB] (IRQs 3 4 5 6 7 10 12 14 15) *0, disabled.
[    0.157835] ACPI: PCI Interrupt Link [LNKC] (IRQs *3 4 5 6 7 10 12 14 15)
[    0.157868] ACPI: PCI Interrupt Link [LNKD] (IRQs 3 4 5 6 *7 10 12 14 15)
[    0.157903] ACPI: PCI Interrupt Link [LNKE] (IRQs 3 4 5 6 7 10 12 14 15) *0, disabled.
[    0.157937] ACPI: PCI Interrupt Link [LNKF] (IRQs 3 4 5 6 7 10 12 14 15) *0, disabled.
[    0.157972] ACPI: PCI Interrupt Link [LNKG] (IRQs *11)
[    0.158004] ACPI: PCI Interrupt Link [LNKH] (IRQs 3 4 *5 6 7 10 12 14 15)
[    0.158066] vgaarb: device added: PCI:0000:00:02.0,decodes=io+mem,owns=io+mem,locks=none
[    0.158066] vgaarb: loaded
[    0.158066] vgaarb: bridge control possible 0000:00:02.0
[    0.158066] PCI: Using ACPI for IRQ routing
[    0.158066] PCI: pci_cache_line_size set to 64 bytes
[    0.158066] Expanded resource reserved due to conflict with PCI Bus 0000:00
[    0.158066] reserve RAM buffer: 000000000009fc00 - 000000000009ffff
[    0.158066] reserve RAM buffer: 00000000ddd80000 - 00000000dfffffff
[    0.158066] HPET: 3 timers in total, 0 timers will be used for per-cpu timer
[    0.158066] hpet0: at MMIO 0xfed00000, IRQs 2, 8, 0
[    0.158066] hpet0: 3 comparators, 64-bit 14.318180 MHz counter
[    0.164139] Switching to clocksource hpet
[    0.165273] pnp: PnP ACPI init
[    0.165282] ACPI: bus type pnp registered
[    0.165347] pnp 00:00: [bus 00-ff]
[    0.165349] pnp 00:00: [io  0x0cf8-0x0cff]
[    0.165351] pnp 00:00: [io  0x0000-0x0cf7 window]
[    0.165352] pnp 00:00: [io  0x0d00-0xffff window]
[    0.165354] pnp 00:00: [mem 0x000a0000-0x000bffff window]
[    0.165356] pnp 00:00: [mem 0x000d0000-0x000dffff window]
[    0.165358] pnp 00:00: [mem 0xdde00000-0xefffffff window]
[    0.165360] pnp 00:00: [mem 0xf4000000-0xffffffff window]
[    0.165390] pnp 00:00: Plug and Play ACPI device, IDs PNP0a08 PNP0a03 (active)
[    0.165397] pnp 00:01: [mem 0xfed14000-0xfed19fff]
[    0.165425] system 00:01: [mem 0xfed14000-0xfed19fff] has been reserved
[    0.165427] system 00:01: Plug and Play ACPI device, IDs PNP0c01 (active)
[    0.165451] pnp 00:02: [dma 4]
[    0.165453] pnp 00:02: [io  0x0000-0x000f]
[    0.165454] pnp 00:02: [io  0x0081-0x0083]
[    0.165456] pnp 00:02: [io  0x0087]
[    0.165457] pnp 00:02: [io  0x0089-0x008b]
[    0.165459] pnp 00:02: [io  0x008f]
[    0.165460] pnp 00:02: [io  0x00c0-0x00df]
[    0.165479] pnp 00:02: Plug and Play ACPI device, IDs PNP0200 (active)
[    0.165488] pnp 00:03: [io  0x0070-0x0071]
[    0.165494] pnp 00:03: [irq 8]
[    0.165514] pnp 00:03: Plug and Play ACPI device, IDs PNP0b00 (active)
[    0.165520] pnp 00:04: [io  0x0061]
[    0.165540] pnp 00:04: Plug and Play ACPI device, IDs PNP0800 (active)
[    0.165547] pnp 00:05: [io  0x00f0-0x00ff]
[    0.165550] pnp 00:05: [irq 13]
[    0.165570] pnp 00:05: Plug and Play ACPI device, IDs PNP0c04 (active)
[    0.165619] pnp 00:06: [io  0x0000-0xffffffffffffffff disabled]
[    0.165621] pnp 00:06: [io  0x0000-0xffffffffffffffff disabled]
[    0.165622] pnp 00:06: [io  0x0290-0x029f]
[    0.165653] system 00:06: [io  0x0290-0x029f] has been reserved
[    0.165656] system 00:06: Plug and Play ACPI device, IDs PNP0c02 (active)
[    0.165730] pnp 00:07: [io  0x0010-0x001f]
[    0.165732] pnp 00:07: [io  0x0022-0x003f]
[    0.165733] pnp 00:07: [io  0x0044-0x005f]
[    0.165735] pnp 00:07: [io  0x0062-0x0063]
[    0.165736] pnp 00:07: [io  0x0065-0x006f]
[    0.165737] pnp 00:07: [io  0x0072-0x007f]
[    0.165739] pnp 00:07: [io  0x0080]
[    0.165740] pnp 00:07: [io  0x0084-0x0086]
[    0.165742] pnp 00:07: [io  0x0088]
[    0.165743] pnp 00:07: [io  0x008c-0x008e]
[    0.165745] pnp 00:07: [io  0x0090-0x009f]
[    0.165746] pnp 00:07: [io  0x00a2-0x00bf]
[    0.165748] pnp 00:07: [io  0x00e0-0x00ef]
[    0.165749] pnp 00:07: [io  0x0400-0x041f]
[    0.165751] pnp 00:07: [io  0x04d0-0x04d1]
[    0.165752] pnp 00:07: [io  0x0800-0x087f]
[    0.165754] pnp 00:07: [io  0x0400-0x03ff disabled]
[    0.165755] pnp 00:07: [io  0x0480-0x04bf]
[    0.165757] pnp 00:07: [mem 0xfed1c000-0xfed1ffff]
[    0.165759] pnp 00:07: [mem 0xfed20000-0xfed8ffff]
[    0.165797] system 00:07: [io  0x0400-0x041f] has been reserved
[    0.165799] system 00:07: [io  0x04d0-0x04d1] has been reserved
[    0.165801] system 00:07: [io  0x0800-0x087f] has been reserved
[    0.165803] system 00:07: [io  0x0480-0x04bf] has been reserved
[    0.165806] system 00:07: [mem 0xfed1c000-0xfed1ffff] has been reserved
[    0.165808] system 00:07: [mem 0xfed20000-0xfed8ffff] has been reserved
[    0.165810] system 00:07: Plug and Play ACPI device, IDs PNP0c02 (active)
[    0.165857] pnp 00:08: [mem 0xfed00000-0xfed003ff]
[    0.165880] pnp 00:08: Plug and Play ACPI device, IDs PNP0103 (active)
[    0.165917] pnp 00:09: [mem 0xffb00000-0xffbfffff]
[    0.165919] pnp 00:09: [mem 0xfff00000-0xffffffff]
[    0.165942] pnp 00:09: Plug and Play ACPI device, IDs INT0800 (active)
[    0.165973] pnp 00:0a: [mem 0xffc00000-0xffefffff]
[    0.166003] system 00:0a: [mem 0xffc00000-0xffefffff] has been reserved
[    0.166006] system 00:0a: Plug and Play ACPI device, IDs PNP0c02 (active)
[    0.166050] pnp 00:0b: [io  0x0000-0xffffffffffffffff disabled]
[    0.166052] pnp 00:0b: [io  0x0000-0xffffffffffffffff disabled]
[    0.166054] pnp 00:0b: [mem 0xfec00000-0xfec00fff]
[    0.166055] pnp 00:0b: [mem 0xfee00000-0xfee00fff]
[    0.166087] system 00:0b: [mem 0xfec00000-0xfec00fff] could not be reserved
[    0.166089] system 00:0b: [mem 0xfee00000-0xfee00fff] has been reserved
[    0.166092] system 00:0b: Plug and Play ACPI device, IDs PNP0c02 (active)
[    0.166112] pnp 00:0c: [io  0x0060]
[    0.166114] pnp 00:0c: [io  0x0064]
[    0.166118] pnp 00:0c: [irq 1]
[    0.166145] pnp 00:0c: Plug and Play ACPI device, IDs PNP0303 PNP030b (active)
[    0.166348] pnp 00:0d: [io  0x03f8-0x03ff]
[    0.166352] pnp 00:0d: [irq 4]
[    0.166354] pnp 00:0d: [dma 0 disabled]
[    0.166411] pnp 00:0d: Plug and Play ACPI device, IDs PNP0501 (active)
[    0.166436] pnp 00:0e: [mem 0xf0000000-0xf3ffffff]
[    0.166468] system 00:0e: [mem 0xf0000000-0xf3ffffff] has been reserved
[    0.166471] system 00:0e: Plug and Play ACPI device, IDs PNP0c02 (active)
[    0.166581] pnp 00:0f: [mem 0x00000000-0x0009ffff]
[    0.166583] pnp 00:0f: [mem 0x000c0000-0x000cffff]
[    0.166584] pnp 00:0f: [mem 0x000e0000-0x000fffff]
[    0.166586] pnp 00:0f: [mem 0x00100000-0xdddfffff]
[    0.166587] pnp 00:0f: [mem 0xf0000000-0xffffffff]
[    0.166626] system 00:0f: [mem 0x00000000-0x0009ffff] could not be reserved
[    0.166628] system 00:0f: [mem 0x000c0000-0x000cffff] could not be reserved
[    0.166630] system 00:0f: [mem 0x000e0000-0x000fffff] could not be reserved
[    0.166633] system 00:0f: [mem 0x00100000-0xdddfffff] could not be reserved
[    0.166635] system 00:0f: [mem 0xf0000000-0xffffffff] could not be reserved
[    0.166637] system 00:0f: Plug and Play ACPI device, IDs PNP0c01 (active)
[    0.166732] pnp: PnP ACPI: found 16 devices
[    0.166733] ACPI: ACPI bus type pnp unregistered
[    0.166736] PnPBIOS: Disabled by ACPI PNP
[    0.202874] PCI: max bus depth: 1 pci_try_num: 2
[    0.202890] pci 0000:00:1c.0: BAR 14: assigned [mem 0xf4000000-0xf41fffff]
[    0.202894] pci 0000:00:1c.0: BAR 15: assigned [mem 0xf4200000-0xf43fffff 64bit pref]
[    0.202897] pci 0000:00:1c.0: BAR 13: assigned [io  0x1000-0x1fff]
[    0.202899] pci 0000:00:1c.0: PCI bridge to [bus 01-01]
[    0.202901] pci 0000:00:1c.0:   bridge window [io  0x1000-0x1fff]
[    0.202905] pci 0000:00:1c.0:   bridge window [mem 0xf4000000-0xf41fffff]
[    0.202908] pci 0000:00:1c.0:   bridge window [mem 0xf4200000-0xf43fffff 64bit pref]
[    0.202913] pci 0000:00:1e.0: PCI bridge to [bus 02-02]
[    0.202915] pci 0000:00:1e.0:   bridge window [io  0xe000-0xefff]
[    0.202919] pci 0000:00:1e.0:   bridge window [mem 0xfeb00000-0xfebfffff]
[    0.202928] pci 0000:00:1c.0: enabling device (0104 -> 0107)
[    0.202936] pci 0000:00:1c.0: setting latency timer to 64
[    0.202941] pci 0000:00:1e.0: setting latency timer to 64
[    0.202943] pci_bus 0000:00: resource 4 [io  0x0000-0x0cf7]
[    0.202945] pci_bus 0000:00: resource 5 [io  0x0d00-0xffff]
[    0.202947] pci_bus 0000:00: resource 6 [mem 0x000a0000-0x000bffff]
[    0.202949] pci_bus 0000:00: resource 7 [mem 0x000d0000-0x000dffff]
[    0.202950] pci_bus 0000:00: resource 8 [mem 0xdde00000-0xefffffff]
[    0.202952] pci_bus 0000:00: resource 9 [mem 0xf4000000-0xffffffff]
[    0.202954] pci_bus 0000:01: resource 0 [io  0x1000-0x1fff]
[    0.202956] pci_bus 0000:01: resource 1 [mem 0xf4000000-0xf41fffff]
[    0.202958] pci_bus 0000:01: resource 2 [mem 0xf4200000-0xf43fffff 64bit pref]
[    0.202959] pci_bus 0000:02: resource 0 [io  0xe000-0xefff]
[    0.202961] pci_bus 0000:02: resource 1 [mem 0xfeb00000-0xfebfffff]
[    0.202963] pci_bus 0000:02: resource 4 [io  0x0000-0x0cf7]
[    0.202965] pci_bus 0000:02: resource 5 [io  0x0d00-0xffff]
[    0.202966] pci_bus 0000:02: resource 6 [mem 0x000a0000-0x000bffff]
[    0.202968] pci_bus 0000:02: resource 7 [mem 0x000d0000-0x000dffff]
[    0.202970] pci_bus 0000:02: resource 8 [mem 0xdde00000-0xefffffff]
[    0.202972] pci_bus 0000:02: resource 9 [mem 0xf4000000-0xffffffff]
[    0.203003] NET: Registered protocol family 2
[    0.203047] IP route cache hash table entries: 32768 (order: 5, 131072 bytes)
[    0.203191] TCP established hash table entries: 131072 (order: 8, 1048576 bytes)
[    0.203434] TCP bind hash table entries: 65536 (order: 7, 524288 bytes)
[    0.203548] TCP: Hash tables configured (established 131072 bind 65536)
[    0.203549] TCP reno registered
[    0.203551] UDP hash table entries: 512 (order: 2, 16384 bytes)
[    0.203556] UDP-Lite hash table entries: 512 (order: 2, 16384 bytes)
[    0.203607] NET: Registered protocol family 1
[    0.203615] pci 0000:00:02.0: Boot video device
[    0.203714] PCI: CLS 32 bytes, default 64
[    0.203742] Unpacking initramfs...
[    0.392046] Freeing initrd memory: 9648k freed
[    0.395418] audit: initializing netlink socket (disabled)
[    0.395429] type=2000 audit(1390399645.388:1): initialized
[    0.409275] highmem bounce pool size: 64 pages
[    0.409279] HugeTLB registered 2 MB page size, pre-allocated 0 pages
[    0.409883] VFS: Disk quotas dquot_6.5.2
[    0.409909] Dquot-cache hash table entries: 1024 (order 0, 4096 bytes)
[    0.409963] msgmni has been set to 1694
[    0.410077] alg: No test for stdrng (krng)
[    0.410098] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 253)
[    0.410101] io scheduler noop registered
[    0.410102] io scheduler deadline registered
[    0.410111] io scheduler cfq registered (default)
[    0.410166] pcieport 0000:00:1c.0: setting latency timer to 64
[    0.410201] pcieport 0000:00:1c.0: irq 40 for MSI/MSI-X
[    0.410266] pci_hotplug: PCI Hot Plug PCI Core version: 0.5
[    0.410281] pciehp: PCI Express Hot Plug Controller Driver version: 0.4
[    0.410283] acpiphp: ACPI Hot Plug PCI Controller Driver version: 0.5
[    0.410504] intel_idle: does not run on family 6 model 23
[    0.410523] ERST: Table is not found!
[    0.410524] GHES: HEST is not enabled!
[    0.410533] isapnp: Scanning for PnP cards...
[    0.763299] isapnp: No Plug & Play device found
[    0.763350] Serial: 8250/16550 driver, 4 ports, IRQ sharing enabled
[    0.783659] serial8250: ttyS0 at I/O 0x3f8 (irq = 4) is a 16550A
[    0.808512] 00:0d: ttyS0 at I/O 0x3f8 (irq = 4) is a 16550A
[    0.808703] Linux agpgart interface v0.103
[    0.808786] agpgart-intel 0000:00:00.0: Intel G41 Chipset
[    0.808843] agpgart-intel 0000:00:00.0: detected gtt size: 2097152K total, 262144K mappable
[    0.810343] agpgart-intel 0000:00:00.0: detected 32768K stolen memory
[    0.810441] agpgart-intel 0000:00:00.0: AGP aperture is 256M @ 0xe0000000
[    0.810562] i8042: PNP: PS/2 Controller [PNP0303:PS2K] at 0x60,0x64 irq 1
[    0.810564] i8042: PNP: PS/2 appears to have AUX port disabled, if this is incorrect please boot with i8042.nopnp
[    0.811077] serio: i8042 KBD port at 0x60,0x64 irq 1
[    0.811158] mousedev: PS/2 mouse device common for all mice
[    0.811198] rtc_cmos 00:03: RTC can wake from S4
[    0.811281] rtc_cmos 00:03: rtc core: registered rtc_cmos as rtc0
[    0.811302] rtc0: alarms up to one month, y3k, 114 bytes nvram, hpet irqs
[    0.811311] cpuidle: using governor ladder
[    0.811313] cpuidle: using governor menu
[    0.811461] TCP cubic registered
[    0.811488] NET: Registered protocol family 10
[    0.811834] Mobile IPv6
[    0.811836] NET: Registered protocol family 17
[    0.811839] Registering the dns_resolver key type
[    0.811857] Using IPI No-Shortcut mode
[    0.811933] PM: Hibernation image not present or could not be loaded.
[    0.811941] registered taskstats version 1
[    0.812351] rtc_cmos 00:03: setting system clock to 2014-01-22 14:07:26 UTC (1390399646)
[    0.812380] Initializing network drop monitor service
[    0.812441] Freeing unused kernel memory: 416k freed
[    0.812556] Write protecting the kernel text: 2856k
[    0.812581] Write protecting the kernel read-only data: 1084k
[    0.812582] NX-protecting the kernel data: 3288k
[    0.820296] udevd[49]: starting version 175
[    0.828194] input: AT Translated Set 2 keyboard as /devices/platform/i8042/serio0/input/input0
[    0.833795] usbcore: registered new interface driver usbfs
[    0.833814] usbcore: registered new interface driver hub
[    0.846994] SCSI subsystem initialized
[    0.851205] usbcore: registered new device driver usb
[    0.851841] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
[    0.851884] ehci_hcd 0000:00:1d.7: setting latency timer to 64
[    0.851887] ehci_hcd 0000:00:1d.7: EHCI Host Controller
[    0.851907] ehci_hcd 0000:00:1d.7: new USB bus registered, assigned bus number 1
[    0.851924] ehci_hcd 0000:00:1d.7: using broken periodic workaround
[    0.851933] ehci_hcd 0000:00:1d.7: debug port 1
[    0.855803] ehci_hcd 0000:00:1d.7: cache line size of 32 is not supported
[    0.862176] ehci_hcd 0000:00:1d.7: irq 23, io mem 0xfeafbc00
[    0.863652] libata version 3.00 loaded.
[    0.868227] e1000: Intel(R) PRO/1000 Network Driver - version 7.3.21-k8-NAPI
[    0.868229] e1000: Copyright (c) 1999-2006 Intel Corporation.
[    0.876022] ehci_hcd 0000:00:1d.7: USB 2.0 started, EHCI 1.00
[    0.876045] usb usb1: New USB device found, idVendor=1d6b, idProduct=0002
[    0.876047] usb usb1: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[    0.876049] usb usb1: Product: EHCI Host Controller
[    0.876051] usb usb1: Manufacturer: Linux 3.2.0-4-686-pae ehci_hcd
[    0.876052] usb usb1: SerialNumber: 0000:00:1d.7
[    0.876145] hub 1-0:1.0: USB hub found
[    0.876148] hub 1-0:1.0: 8 ports detected
[    0.876446] uhci_hcd: USB Universal Host Controller Interface driver
[    0.876477] uhci_hcd 0000:00:1d.0: setting latency timer to 64
[    0.876480] uhci_hcd 0000:00:1d.0: UHCI Host Controller
[    0.876486] uhci_hcd 0000:00:1d.0: new USB bus registered, assigned bus number 2
[    0.876508] uhci_hcd 0000:00:1d.0: irq 23, io base 0x0000d400
[    0.876531] usb usb2: New USB device found, idVendor=1d6b, idProduct=0001
[    0.876533] usb usb2: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[    0.876535] usb usb2: Product: UHCI Host Controller
[    0.876536] usb usb2: Manufacturer: Linux 3.2.0-4-686-pae uhci_hcd
[    0.876538] usb usb2: SerialNumber: 0000:00:1d.0
[    0.876841] hub 2-0:1.0: USB hub found
[    0.876844] hub 2-0:1.0: 2 ports detected
[    0.876896] uhci_hcd 0000:00:1d.1: setting latency timer to 64
[    0.876899] uhci_hcd 0000:00:1d.1: UHCI Host Controller
[    0.876904] uhci_hcd 0000:00:1d.1: new USB bus registered, assigned bus number 3
[    0.876935] uhci_hcd 0000:00:1d.1: irq 19, io base 0x0000d480
[    0.876957] usb usb3: New USB device found, idVendor=1d6b, idProduct=0001
[    0.876959] usb usb3: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[    0.876961] usb usb3: Product: UHCI Host Controller
[    0.876962] usb usb3: Manufacturer: Linux 3.2.0-4-686-pae uhci_hcd
[    0.876964] usb usb3: SerialNumber: 0000:00:1d.1
[    0.877041] hub 3-0:1.0: USB hub found
[    0.877044] hub 3-0:1.0: 2 ports detected
[    0.877096] uhci_hcd 0000:00:1d.2: setting latency timer to 64
[    0.877098] uhci_hcd 0000:00:1d.2: UHCI Host Controller
[    0.877104] uhci_hcd 0000:00:1d.2: new USB bus registered, assigned bus number 4
[    0.877129] uhci_hcd 0000:00:1d.2: irq 18, io base 0x0000d800
[    0.877151] usb usb4: New USB device found, idVendor=1d6b, idProduct=0001
[    0.877153] usb usb4: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[    0.877155] usb usb4: Product: UHCI Host Controller
[    0.877157] usb usb4: Manufacturer: Linux 3.2.0-4-686-pae uhci_hcd
[    0.877158] usb usb4: SerialNumber: 0000:00:1d.2
[    0.877234] hub 4-0:1.0: USB hub found
[    0.877237] hub 4-0:1.0: 2 ports detected
[    0.877287] uhci_hcd 0000:00:1d.3: setting latency timer to 64
[    0.877290] uhci_hcd 0000:00:1d.3: UHCI Host Controller
[    0.877295] uhci_hcd 0000:00:1d.3: new USB bus registered, assigned bus number 5
[    0.877322] uhci_hcd 0000:00:1d.3: irq 16, io base 0x0000d880
[    0.877344] usb usb5: New USB device found, idVendor=1d6b, idProduct=0001
[    0.877346] usb usb5: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[    0.877347] usb usb5: Product: UHCI Host Controller
[    0.877349] usb usb5: Manufacturer: Linux 3.2.0-4-686-pae uhci_hcd
[    0.877350] usb usb5: SerialNumber: 0000:00:1d.3
[    0.877426] hub 5-0:1.0: USB hub found
[    0.877429] hub 5-0:1.0: 2 ports detected
[    0.878346] ata_piix 0000:00:1f.1: version 2.13
[    0.878379] ata_piix 0000:00:1f.1: setting latency timer to 64
[    0.883385] scsi0 : ata_piix
[    0.884909] scsi1 : ata_piix
[    0.885781] ata1: PATA max UDMA/100 cmd 0x1f0 ctl 0x3f6 bmdma 0xffa0 irq 14
[    0.885783] ata2: PATA max UDMA/100 cmd 0x170 ctl 0x376 bmdma 0xffa8 irq 15
[    0.885839] ata_piix 0000:00:1f.2: MAP [ P0 P2 P1 P3 ]
[    0.885865] ata_piix 0000:00:1f.2: setting latency timer to 64
[    0.886091] scsi2 : ata_piix
[    0.886200] scsi3 : ata_piix
[    0.887305] ata3: SATA max UDMA/133 cmd 0xd080 ctl 0xd000 bmdma 0xc800 irq 22
[    0.887308] ata4: SATA max UDMA/133 cmd 0xcc00 ctl 0xc880 bmdma 0xc808 irq 22
[    1.068263] ata4.01: ATAPI: HL-DT-ST DVDRAM GH24NS95, RN00, max UDMA/133
[    1.076397] ata3.00: ATA-8: ST3500418AS, CC49, max UDMA/133
[    1.076399] ata3.00: 976773168 sectors, multi 16: LBA48 NCQ (depth 0/32)
[    1.076630] ata3.01: HPA detected: current 3907027055, native 3907029168
[    1.076633] ata3.01: ATA-8: ST2000DL003-9VT166, CC3C, max UDMA/133
[    1.076634] ata3.01: 3907027055 sectors, multi 16: LBA48 NCQ (depth 0/32)
[    1.084190] ata4.01: configured for UDMA/133
[    1.092304] ata3.00: configured for UDMA/133
[    1.108313] ata3.01: configured for UDMA/133
[    1.108386] scsi 2:0:0:0: Direct-Access     ATA      ST3500418AS      CC49 PQ: 0 ANSI: 5
[    1.108512] scsi 2:0:1:0: Direct-Access     ATA      ST2000DL003-9VT1 CC3C PQ: 0 ANSI: 5
[    1.111375] scsi 3:0:1:0: CD-ROM            HL-DT-ST DVDRAM GH24NS95  RN00 PQ: 0 ANSI: 5
[    1.117124] sd 2:0:0:0: [sda] 976773168 512-byte logical blocks: (500 GB/465 GiB)
[    1.117159] sd 2:0:0:0: [sda] Write Protect is off
[    1.117161] sd 2:0:0:0: [sda] Mode Sense: 00 3a 00 00
[    1.117177] sd 2:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
[    1.119608] sd 2:0:0:0: Attached scsi generic sg0 type 0
[    1.119657] sd 2:0:1:0: Attached scsi generic sg1 type 0
[    1.119703] sr 3:0:1:0: Attached scsi generic sg2 type 5
[    1.121724] sr0: scsi3-mmc drive: 48x/12x writer dvd-ram cd/rw xa/form2 cdda tray
[    1.121726] cdrom: Uniform CD-ROM driver Revision: 3.20
[    1.121796] sr 3:0:1:0: Attached scsi CD-ROM sr0
[    1.161203] sd 2:0:1:0: [sdb] 3907027055 512-byte logical blocks: (2.00 TB/1.81 TiB)
[    1.161206]  sda: sda1 sda2 < sda5 >
[    1.161210] sd 2:0:1:0: [sdb] 4096-byte physical blocks
[    1.161266] sd 2:0:1:0: [sdb] Write Protect is off
[    1.161269] sd 2:0:1:0: [sdb] Mode Sense: 00 3a 00 00
[    1.161292] sd 2:0:1:0: [sdb] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
[    1.161463] sd 2:0:0:0: [sda] Attached SCSI disk
[    1.212380]  sdb: sdb1 sdb2
[    1.212608] sd 2:0:1:0: [sdb] Attached SCSI disk
[    1.314477] e1000 0000:02:01.0: eth0: (PCI:33MHz:32-bit) 00:1b:21:82:74:b3
[    1.314480] e1000 0000:02:01.0: eth0: Intel(R) PRO/1000 Network Connection
[    1.392038] Refined TSC clocksource calibration: 3000.851 MHz.
[    1.392043] Switching to clocksource tsc
[    1.775635] PM: Starting manual resume from disk
[    1.775638] PM: Hibernation image partition 8:5 present
[    1.775639] PM: Looking for hibernation image.
[    1.775886] PM: Image not found (code -22)
[    1.775889] PM: Hibernation image not present or could not be loaded.
[    1.817240] EXT4-fs (sda1): mounted filesystem with ordered data mode. Opts: (null)
[    3.567995] udevd[343]: starting version 175
[    4.078753] intel_rng: FWH not detected
[    4.148500] input: Power Button as /devices/LNXSYSTM:00/LNXSYBUS:00/PNP0C0C:00/input/input1
[    4.148506] ACPI: Power Button [PWRB]
[    4.148556] input: Power Button as /devices/LNXSYSTM:00/LNXPWRBN:00/input/input2
[    4.148559] ACPI: Power Button [PWRF]
[    4.169159] input: PC Speaker as /devices/platform/pcspkr/input/input3
[    4.171462] iTCO_vendor_support: vendor-support=0
[    4.181376] iTCO_wdt: Intel TCO WatchDog Timer Driver v1.07
[    4.181430] iTCO_wdt: Found a ICH7 or ICH7R TCO device (Version=2, TCOBASE=0x0860)
[    4.181467] iTCO_wdt: initialized. heartbeat=30 sec (nowayout=0)
[    4.208944] leds_ss4200: no LED devices found
[    4.312322] [drm] Initialized drm 1.1.0 20060810
[    4.449114] Error: Driver 'pcspkr' is already registered, aborting...
[    4.456488] i915 0000:00:02.0: setting latency timer to 64
[    4.467627] mtrr: type mismatch for e0000000,10000000 old: write-back new: write-combining
[    4.467628] [drm] MTRR allocation failed.  Graphics performance may suffer.
[    4.467778] i915 0000:00:02.0: irq 41 for MSI/MSI-X
[    4.467782] [drm] Supports vblank timestamp caching Rev 1 (10.10.2010).
[    4.467784] [drm] Driver supports precise vblank timestamp query.
[    4.467805] vgaarb: device changed decodes: PCI:0000:00:02.0,olddecodes=io+mem,decodes=io+mem :o wns=io+mem
[    4.536324] fbcon: inteldrmfb (fb0) is primary device
[    4.579627] Console: switching to colour frame buffer device 170x48
[    4.582697] fb0: inteldrmfb frame buffer device
[    4.582699] drm: registered panic notifier
[    4.582707] No ACPI video bus found
[    4.582734] [drm] Initialized i915 1.6.0 20080730 for 0000:00:02.0 on minor 0
[    5.476006] Adding 5066748k swap on /dev/sda5.  Priority:-1 extents:1 across:5066748k
[    5.484483] EXT4-fs (sda1): re-mounted. Opts: (null)
[    5.704017] EXT4-fs (sda1): re-mounted. Opts: errors=remount-ro
[    5.891840] loop: module loaded
[    6.391724] EXT4-fs (sdb1): mounted filesystem with ordered data mode. Opts: errors=remount-ro
[    7.057402] RPC: Registered named UNIX socket transport module.
[    7.057404] RPC: Registered udp transport module.
[    7.057405] RPC: Registered tcp transport module.
[    7.057407] RPC: Registered tcp NFSv4.1 backchannel transport module.
[    7.123497] FS-Cache: Loaded
[    7.166741] FS-Cache: Netfs 'nfs' registered for caching
[    7.176262] Installing knfsd (copyright (C) 1996 [EMAIL="okir@monad.swb.de"]okir@monad.swb.de[/EMAIL]).

ODPOWIEDZ