Nie mogę połączyć się z siecią zabezpieczoną wpa2:
Kod: Zaznacz cały
wpa_supplicant -B -c /etc/wpa_supplicant.conf -iwlan0
Kod: Zaznacz cały
ioctl[SIOCSIWENCODEEXT]: Invalid argument
ioctl[SIOCSIWENCODEEXT]: Invalid argument
Kod: Zaznacz cały
wpa_supplicant -B -c /etc/wpa_supplicant.conf -iwlan0 -d
Kod: Zaznacz cały
random: Trying to read entropy from /dev/random
Initializing interface 'wlan0' conf '/etc/wpa_supplicant.conf' driver 'default' ctrl_interface 'N/A' bridge 'N/A'
Configuration file '/etc/wpa_supplicant.conf' -> '/etc/wpa_supplicant.conf'
Reading configuration file '/etc/wpa_supplicant.conf'
ctrl_interface='/var/run/wpa_supplicant'
Priority group 0
id=0 ssid='moja siec'
WEXT: cfg80211-based driver detected
wext: interface wlan0 phy: phy0
rfkill: initial event: idx=0 type=1 op=0 soft=0 hard=0
rfkill: initial event: idx=1 type=1 op=0 soft=0 hard=0
SIOCGIWRANGE: WE(compiled)=22 WE(source)=21 enc_capa=0xf
capabilities: key_mgmt 0xf enc 0xf flags 0x0
netlink: Operstate: linkmode=1, operstate=5
wlan0: Own MAC address: 00:26:82:a0:22:2d
wpa_driver_wext_set_key: alg=0 key_idx=0 set_tx=0 seq_len=0 key_len=0
wpa_driver_wext_set_key: alg=0 key_idx=1 set_tx=0 seq_len=0 key_len=0
wpa_driver_wext_set_key: alg=0 key_idx=2 set_tx=0 seq_len=0 key_len=0
wpa_driver_wext_set_key: alg=0 key_idx=3 set_tx=0 seq_len=0 key_len=0
wpa_driver_wext_set_key: alg=0 key_idx=4 set_tx=0 seq_len=0 key_len=0
ioctl[SIOCSIWENCODEEXT]: Invalid argument
Driver did not support SIOCSIWENCODEEXT
wpa_driver_wext_set_key: alg=0 key_idx=5 set_tx=0 seq_len=0 key_len=0
ioctl[SIOCSIWENCODEEXT]: Invalid argument
[B]Driver did not support SIOCSIWENCODEEXT[/B]
wpa_driver_wext_set_countermeasures
wlan0: RSN: flushing PMKID list in the driver
wlan0: Setting scan request: 0 sec 100000 usec
WPS: Set UUID for interface wlan0
WPS: UUID based on MAC address - hexdump(len=16): 6d 42 ef 2d 83 5a 5b f5 9e 61 c7 85 d2 a2 de f0
EAPOL: SUPP_PAE entering state DISCONNECTED
EAPOL: Supplicant port status: Unauthorized
EAPOL: KEY_RX entering state NO_KEY_RECEIVE
EAPOL: SUPP_BE entering state INITIALIZE
EAP: EAP entering state DISABLED
EAPOL: Supplicant port status: Unauthorized
EAPOL: Supplicant port status: Unauthorized
Using existing control interface directory.
wlan0: Added interface wlan0
Daemonize..
Kod: Zaznacz cały
cat /etc/wpa_supplicant.conf
ctrl_interface=/var/run/wpa_supplicant
network={
ssid="moja siec"
key_mgmt=WPA-PSK
psk="moje haslo"
}
Kod: Zaznacz cały
lspsci -k
03:00.0 Network controller: Broadcom Corporation BCM4313 802.11b/g/n Wireless LAN Controller (rev 01)
Subsystem: Hewlett-Packard Company Device 145c
Kernel driver in use: brcmsmac
Kod: Zaznacz cały
cat /etc/network/interfaces
auto wlan0
iface wlan0 inet dhcp
Kod: Zaznacz cały
iwconfig
lo no wireless extensions.
wlan0 IEEE 802.11bgn ESSID :o ff/any
Mode:Managed Access Point: Not-Associated Tx-Power=off
Retry long limit:7 RTS thr :o ff Fragment thr :o ff
Encryption key :o ff
Power Management :o ff
eth0 no wireless extensions.
Kod: Zaznacz cały
dpkg --print-architecture
amd64
Kod: Zaznacz cały
uname -r
3.2.0-2-amd64
Kod: Zaznacz cały
cat /etc/debian_version
wheezy/sid
Przy wyłączonym WPA2 w ruterze, łączy się bez problemu. Sprawdzałem również na Windowsie i tam przy włączonych zabezpieczeniach działa, a więc to raczej nie wina sprzętu a sterownika jak mniemam.
Tylko (panie Premierze) - co robić?